/* setup board specific PMIC */
int power_init_board(void)
{
struct pmic *p;
u32 reg;
int ret;
power_pfuze100_init(1);
p = pmic_get("PFUZE100");
if (!p)
return -EINVAL;
ret = pmic_probe(p);
if (ret)
return ret;
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
/* Set SWBST to 5.0V and enable (for USB) */
pmic_reg_read(p, PFUZE100_SWBSTCON1, ®);
reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK);
reg |= (SWBST_5_00V | SWBST_MODE_AUTO);
pmic_reg_write(p, PFUZE100_SWBSTCON1, reg);
return 0;
}
int power_init_board(void)
{
struct pmic *p;
int ret;
unsigned int reg;
ret = power_pfuze100_init(I2C_PMIC);
if (ret)
return ret;
p = pmic_get("PFUZE100");
ret = pmic_probe(p);
if (ret)
return ret;
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
/* Increase VGEN3 from 2.5 to 2.8V */
pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
reg &= ~LDO_VOL_MASK;
reg |= LDOB_2_80V;
pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
/* Increase VGEN5 from 2.8 to 3V */
pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
reg &= ~LDO_VOL_MASK;
reg |= LDOB_3_00V;
pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
/* Set SW1AB stanby volage to 0.975V */
pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®);
reg &= ~SW1x_STBY_MASK;
reg |= SW1x_0_975V;
pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
pmic_reg_read(p, PFUZE100_SW1ABCONF, ®);
reg &= ~SW1xCONF_DVSSPEED_MASK;
reg |= SW1xCONF_DVSSPEED_4US;
pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
/* Set SW1C standby voltage to 0.975V */
pmic_reg_read(p, PFUZE100_SW1CSTBY, ®);
reg &= ~SW1x_STBY_MASK;
reg |= SW1x_0_975V;
pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
pmic_reg_read(p, PFUZE100_SW1CCONF, ®);
reg &= ~SW1xCONF_DVSSPEED_MASK;
reg |= SW1xCONF_DVSSPEED_4US;
pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
return 0;
}
static int pfuze_init(void)
{
struct pmic *p;
int ret;
unsigned int reg;
ret = power_pfuze100_init(I2C_PMIC);
if (ret)
return ret;
p = pmic_get("PFUZE100");
ret = pmic_probe(p);
if (ret)
return ret;
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
/* Set SW1AB standby voltage to 0.975V */
pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®);
reg &= ~0x3f;
reg |= 0x1b;
pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
pmic_reg_read(p, PUZE_100_SW1ABCONF, ®);
reg &= ~0xc0;
reg |= 0x40;
pmic_reg_write(p, PUZE_100_SW1ABCONF, reg);
/* Set SW1C standby voltage to 0.975V */
pmic_reg_read(p, PFUZE100_SW1CSTBY, ®);
reg &= ~0x3f;
reg |= 0x1b;
pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
pmic_reg_read(p, PFUZE100_SW1CCONF, ®);
reg &= ~0xc0;
reg |= 0x40;
pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
/* Enable power of VGEN5 3V3, needed for SD3 */
pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
reg &= ~0x1F;
reg |= 0x1F;
pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
return 0;
}
/* setup board specific PMIC */
int power_init_board(void)
{
struct pmic *p;
u32 id1, id2, i;
int ret;
char const *lv_mipi;
/* configure I2C multiplexer */
gpio_direction_output(MX6Q_QMX6_PFUZE_MUX, 1);
power_pfuze100_init(I2C_PMIC);
p = pmic_get("PFUZE100");
if (!p)
return -EINVAL;
ret = pmic_probe(p);
if (ret)
return ret;
pmic_reg_read(p, PFUZE100_DEVICEID, &id1);
pmic_reg_read(p, PFUZE100_REVID, &id2);
printf("PFUZE100 Rev. [%02x/%02x] detected\n", id1, id2);
if (id2 >= 0x20)
return 0;
/* set level of MIPI if specified */
lv_mipi = getenv("lv_mipi");
if (lv_mipi)
return 0;
for (i = 0; i < ARRAY_SIZE(mipi_levels); i++) {
if (!strcmp(mipi_levels[i].name, lv_mipi)) {
printf("set MIPI level %s\n",
mipi_levels[i].name);
ret = pmic_reg_write(p, PFUZE100_VGEN4VOL,
mipi_levels[i].value);
if (ret)
return ret;
}
}
return 0;
}
struct pmic *pfuze_common_init(unsigned char i2cbus)
{
struct pmic *p;
int ret;
unsigned int reg;
ret = power_pfuze100_init(i2cbus);
if (ret)
return NULL;
p = pmic_get("PFUZE100");
ret = pmic_probe(p);
if (ret)
return NULL;
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
/* Set SW1AB stanby volage to 0.975V */
pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®);
reg &= ~SW1x_STBY_MASK;
reg |= SW1x_0_975V;
pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
pmic_reg_read(p, PFUZE100_SW1ABCONF, ®);
reg &= ~SW1xCONF_DVSSPEED_MASK;
reg |= SW1xCONF_DVSSPEED_4US;
pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
/* Set SW1C standby voltage to 0.975V */
pmic_reg_read(p, PFUZE100_SW1CSTBY, ®);
reg &= ~SW1x_STBY_MASK;
reg |= SW1x_0_975V;
pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
pmic_reg_read(p, PFUZE100_SW1CCONF, ®);
reg &= ~SW1xCONF_DVSSPEED_MASK;
reg |= SW1xCONF_DVSSPEED_4US;
pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
return p;
}
int board_late_init(void)
{
struct pmic *p;
u32 reg;
setenv("board_name", tqma6_get_boardname());
/*
* configure PFUZE100 PMIC:
* TODO: should go to power_init_board if bus switching is
* fixed in generic power code
*/
power_pfuze100_init(TQMA6_PFUZE100_I2C_BUS);
p = pmic_get("PFUZE100");
if (p && !pmic_probe(p)) {
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
}
tqma6_bb_board_late_init();
return 0;
}
int power_init_board(void)
{
struct pmic *p;
int ret;
unsigned int reg;
ret = power_pfuze100_init(I2C_PMIC);
if (ret)
return -ENODEV;
p = pmic_get("PFUZE100");
ret = pmic_probe(p);
if (ret)
return -ENODEV;
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
pmic_reg_read(p, PFUZE100_SW3AVOL, ®);
if ((reg & 0x3f) != 0x18) {
reg &= ~0x3f;
reg |= 0x18;
pmic_reg_write(p, PFUZE100_SW3AVOL, reg);
}
ret = pfuze_mode_init(p, APS_PFM);
if (ret < 0)
return ret;
/* set SW3A standby mode to off */
pmic_reg_read(p, PFUZE100_SW3AMODE, ®);
reg &= ~0xf;
reg |= APS_OFF;
pmic_reg_write(p, PFUZE100_SW3AMODE, reg);
return 0;
}
/* setup board specific PMIC */
void setup_pmic(void)
{
struct pmic *p;
u32 reg;
i2c_set_bus_num(CONFIG_I2C_PMIC);
/* configure PFUZE100 PMIC */
if (!i2c_probe(CONFIG_POWER_PFUZE100_I2C_ADDR)) {
debug("probed PFUZE100@0x%x\n", CONFIG_POWER_PFUZE100_I2C_ADDR);
power_pfuze100_init(CONFIG_I2C_PMIC);
p = pmic_get("PFUZE100");
if (p && !pmic_probe(p)) {
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
/* Set VGEN1 to 1.5V and enable */
pmic_reg_read(p, PFUZE100_VGEN1VOL, ®);
reg &= ~(LDO_VOL_MASK);
reg |= (LDOA_1_50V | LDO_EN);
pmic_reg_write(p, PFUZE100_VGEN1VOL, reg);
/* Set SWBST to 5.0V and enable */
pmic_reg_read(p, PFUZE100_SWBSTCON1, ®);
reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK);
reg |= (SWBST_5_00V | (SWBST_MODE_AUTO << SWBST_MODE_SHIFT));
pmic_reg_write(p, PFUZE100_SWBSTCON1, reg);
}
}
/* configure LTC3676 PMIC */
else if (!i2c_probe(CONFIG_POWER_LTC3676_I2C_ADDR)) {
debug("probed LTC3676@0x%x\n", CONFIG_POWER_LTC3676_I2C_ADDR);
power_ltc3676_init(CONFIG_I2C_PMIC);
p = pmic_get("LTC3676_PMIC");
if (p && !pmic_probe(p)) {
puts("PMIC: LTC3676\n");
/*
* set board-specific scalar for max CPU frequency
* per CPU based on the LDO enabled Operating Ranges
* defined in the respective IMX6DQ and IMX6SDL
* datasheets. The voltage resulting from the R1/R2
* feedback inputs on Ventana is 1308mV. Note that this
* is a bit shy of the Vmin of 1350mV in the datasheet
* for LDO enabled mode but is as high as we can go.
*
* We will rely on an OS kernel driver to properly
* regulate these per CPU operating point and use LDO
* bypass mode when using the higher frequency
* operating points to compensate as LDO bypass mode
* allows the rails be 125mV lower.
*/
/* mask PGOOD during SW1 transition */
pmic_reg_write(p, LTC3676_DVB1B,
0x1f | LTC3676_PGOOD_MASK);
/* set SW1 (VDD_SOC) */
pmic_reg_write(p, LTC3676_DVB1A, 0x1f);
/* mask PGOOD during SW3 transition */
pmic_reg_write(p, LTC3676_DVB3B,
0x1f | LTC3676_PGOOD_MASK);
/* set SW3 (VDD_ARM) */
pmic_reg_write(p, LTC3676_DVB3A, 0x1f);
}
}
}
int power_init_board(void)
{
int ret;
u32 rev_id, value;
ret = power_pfuze100_init(I2C_PMIC);
if (ret)
return ret;
pfuze = pmic_get("PFUZE100");
if (!pfuze)
return -ENODEV;
ret = pmic_probe(pfuze);
if (ret)
return ret;
ret = pfuze_mode_init(pfuze, APS_PFM);
if (ret < 0)
return ret;
pmic_reg_read(pfuze, PFUZE100_DEVICEID, &value);
pmic_reg_read(pfuze, PFUZE100_REVID, &rev_id);
printf("PMIC: PFUZE200! DEV_ID=0x%x REV_ID=0x%x\n", value, rev_id);
/*
* Our PFUZE0200 is PMPF0200X0AEP, the Pre-programmed OTP
* Configuration is F0.
* Default VOLT:
* VSNVS_VOLT | 3.0V
* SW1AB | 1.375V
* SW2 | 3.3V
* SW3A | 1.5V
* SW3B | 1.5V
* VGEN1 | 1.5V
* VGEN2 | 1.5V
* VGEN3 | 2.5V
* VGEN4 | 1.8V
* VGEN5 | 2.8V
* VGEN6 | 3.3V
*
* According to schematic, we need SW3A 1.35V, SW3B 3.3V,
* VGEN1 1.2V, VGEN2 1.5V, VGEN3 2.8V, VGEN4 1.8V,
* VGEN5 3.3V, VGEN6 3.0V.
*
* Here we just use the default VOLT, but not configure
* them, when needed, configure them to our requested voltage.
*/
/* set SW1AB standby volatage 1.3V */
pmic_reg_read(pfuze, PFUZE100_SW1ABSTBY, &value);
value &= ~0x3f;
value |= PFUZE100_SW1ABC_SETP(13000);
pmic_reg_write(pfuze, PFUZE100_SW1ABSTBY, value);
/* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
pmic_reg_read(pfuze, PFUZE100_SW1ABCONF, &value);
value &= ~0xc0;
value |= 0x40;
pmic_reg_write(pfuze, PFUZE100_SW1ABCONF, value);
/* Enable power of VGEN5 3V3 */
pmic_reg_read(pfuze, PFUZE100_VGEN5VOL, &value);
value &= ~0x1F;
value |= 0x1F;
pmic_reg_write(pfuze, PFUZE100_VGEN5VOL, value);
return 0;
}