static netdev_tx_t elp_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
unsigned long flags;
elp_device *adapter = netdev_priv(dev);
spin_lock_irqsave(&adapter->lock, flags);
check_3c505_dma(dev);
if (elp_debug >= 3)
pr_debug("%s: request to send packet of length %d\n", dev->name, (int) skb->len);
netif_stop_queue(dev);
/*
* send the packet at skb->data for skb->len
*/
if (!send_packet(dev, skb)) {
if (elp_debug >= 2) {
pr_debug("%s: failed to transmit packet\n", dev->name);
}
spin_unlock_irqrestore(&adapter->lock, flags);
return NETDEV_TX_BUSY;
}
if (elp_debug >= 3)
pr_debug("%s: packet of length %d sent\n", dev->name, (int) skb->len);
prime_rx(dev);
spin_unlock_irqrestore(&adapter->lock, flags);
netif_start_queue(dev);
return NETDEV_TX_OK;
}
static int elp_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
unsigned long flags;
elp_device *adapter = dev->priv;
spin_lock_irqsave(&adapter->lock, flags);
check_3c505_dma(dev);
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: request to send packet of length %d\n", dev->name, (int) skb->len);
netif_stop_queue(dev);
/*
* send the packet at skb->data for skb->len
*/
if (!send_packet(dev, skb)) {
if (elp_debug >= 2) {
printk(KERN_DEBUG "%s: failed to transmit packet\n", dev->name);
}
spin_unlock_irqrestore(&adapter->lock, flags);
return 1;
}
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: packet of length %d sent\n", dev->name, (int) skb->len);
/*
* start the transmit timeout
*/
dev->trans_start = jiffies;
prime_rx(dev);
spin_unlock_irqrestore(&adapter->lock, flags);
netif_start_queue(dev);
return 0;
}
static int elp_open(struct net_device *dev)
{
elp_device *adapter;
int retval;
adapter = dev->priv;
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: request to open device\n", dev->name);
/*
* make sure we actually found the device
*/
if (adapter == NULL) {
printk(KERN_ERR "%s: Opening a non-existent physical device\n", dev->name);
return -EAGAIN;
}
/*
* disable interrupts on the board
*/
outb_control(0, dev);
/*
* clear any pending interrupts
*/
inb_command(dev->base_addr);
adapter_reset(dev);
/*
* no receive PCBs active
*/
adapter->rx_active = 0;
adapter->busy = 0;
adapter->send_pcb_semaphore = 0;
adapter->rx_backlog.in = 0;
adapter->rx_backlog.out = 0;
spin_lock_init(&adapter->lock);
/*
* install our interrupt service routine
*/
if ((retval = request_irq(dev->irq, &elp_interrupt, 0, dev->name, dev))) {
printk(KERN_ERR "%s: could not allocate IRQ%d\n", dev->name, dev->irq);
return retval;
}
if ((retval = request_dma(dev->dma, dev->name))) {
free_irq(dev->irq, dev);
printk(KERN_ERR "%s: could not allocate DMA%d channel\n", dev->name, dev->dma);
return retval;
}
adapter->dma_buffer = (void *) dma_mem_alloc(DMA_BUFFER_SIZE);
if (!adapter->dma_buffer) {
printk(KERN_ERR "%s: could not allocate DMA buffer\n", dev->name);
free_dma(dev->dma);
free_irq(dev->irq, dev);
return -ENOMEM;
}
adapter->dmaing = 0;
/*
* enable interrupts on the board
*/
outb_control(CMDE, dev);
/*
* configure adapter memory: we need 10 multicast addresses, default==0
*/
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: sending 3c505 memory configuration command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_ADAPTER_MEMORY;
adapter->tx_pcb.data.memconf.cmd_q = 10;
adapter->tx_pcb.data.memconf.rcv_q = 20;
adapter->tx_pcb.data.memconf.mcast = 10;
adapter->tx_pcb.data.memconf.frame = 20;
adapter->tx_pcb.data.memconf.rcv_b = 20;
adapter->tx_pcb.data.memconf.progs = 0;
adapter->tx_pcb.length = sizeof(struct Memconf);
adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
printk(KERN_ERR "%s: couldn't send memory configuration command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
/*
* configure adapter to receive broadcast messages and wait for response
*/
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: sending 82586 configure command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_82586;
adapter->tx_pcb.data.configure = NO_LOOPBACK | RECV_BROAD;
adapter->tx_pcb.length = 2;
adapter->got[CMD_CONFIGURE_82586] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
printk(KERN_ERR "%s: couldn't send 82586 configure command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_CONFIGURE_82586] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
/* enable burst-mode DMA */
/* outb(0x1, dev->base_addr + PORT_AUXDMA); */
/*
* queue receive commands to provide buffering
*/
prime_rx(dev);
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: %d receive PCBs active\n", dev->name, adapter->rx_active);
/*
* device is now officially open!
*/
netif_start_queue(dev);
return 0;
}
static irqreturn_t elp_interrupt(int irq, void *dev_id)
{
int len;
int dlen;
int icount = 0;
struct net_device *dev;
elp_device *adapter;
unsigned long timeout;
dev = dev_id;
adapter = (elp_device *) dev->priv;
spin_lock(&adapter->lock);
do {
/*
* has a DMA transfer finished?
*/
if (inb_status(dev->base_addr) & DONE) {
if (!adapter->dmaing) {
printk(KERN_WARNING "%s: phantom DMA completed\n", dev->name);
}
if (elp_debug >= 3) {
printk(KERN_DEBUG "%s: %s DMA complete, status %02x\n", dev->name, adapter->current_dma.direction ? "tx" : "rx", inb_status(dev->base_addr));
}
outb_control(adapter->hcr_val & ~(DMAE | TCEN | DIR), dev);
if (adapter->current_dma.direction) {
dev_kfree_skb_irq(adapter->current_dma.skb);
} else {
struct sk_buff *skb = adapter->current_dma.skb;
if (skb) {
if (adapter->current_dma.target) {
/* have already done the skb_put() */
memcpy(adapter->current_dma.target, adapter->dma_buffer, adapter->current_dma.length);
}
skb->protocol = eth_type_trans(skb,dev);
adapter->stats.rx_bytes += skb->len;
netif_rx(skb);
dev->last_rx = jiffies;
}
}
adapter->dmaing = 0;
if (adapter->rx_backlog.in != adapter->rx_backlog.out) {
int t = adapter->rx_backlog.length[adapter->rx_backlog.out];
adapter->rx_backlog.out = backlog_next(adapter->rx_backlog.out);
if (elp_debug >= 2)
printk(KERN_DEBUG "%s: receiving backlogged packet (%d)\n", dev->name, t);
receive_packet(dev, t);
} else {
adapter->busy = 0;
}
} else {
/* has one timed out? */
check_3c505_dma(dev);
}
/*
* receive a PCB from the adapter
*/
timeout = jiffies + 3*HZ/100;
while ((inb_status(dev->base_addr) & ACRF) != 0 && time_before(jiffies, timeout)) {
if (receive_pcb(dev, &adapter->irx_pcb)) {
switch (adapter->irx_pcb.command)
{
case 0:
break;
/*
* received a packet - this must be handled fast
*/
case 0xff:
case CMD_RECEIVE_PACKET_COMPLETE:
/* if the device isn't open, don't pass packets up the stack */
if (!netif_running(dev))
break;
len = adapter->irx_pcb.data.rcv_resp.pkt_len;
dlen = adapter->irx_pcb.data.rcv_resp.buf_len;
if (adapter->irx_pcb.data.rcv_resp.timeout != 0) {
printk(KERN_ERR "%s: interrupt - packet not received correctly\n", dev->name);
} else {
if (elp_debug >= 3) {
printk(KERN_DEBUG "%s: interrupt - packet received of length %i (%i)\n", dev->name, len, dlen);
}
if (adapter->irx_pcb.command == 0xff) {
if (elp_debug >= 2)
printk(KERN_DEBUG "%s: adding packet to backlog (len = %d)\n", dev->name, dlen);
adapter->rx_backlog.length[adapter->rx_backlog.in] = dlen;
adapter->rx_backlog.in = backlog_next(adapter->rx_backlog.in);
} else {
receive_packet(dev, dlen);
}
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: packet received\n", dev->name);
}
break;
/*
* 82586 configured correctly
*/
case CMD_CONFIGURE_82586_RESPONSE:
adapter->got[CMD_CONFIGURE_82586] = 1;
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: interrupt - configure response received\n", dev->name);
break;
/*
* Adapter memory configuration
*/
case CMD_CONFIGURE_ADAPTER_RESPONSE:
adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] = 1;
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: Adapter memory configuration %s.\n", dev->name,
adapter->irx_pcb.data.failed ? "failed" : "succeeded");
break;
/*
* Multicast list loading
*/
case CMD_LOAD_MULTICAST_RESPONSE:
adapter->got[CMD_LOAD_MULTICAST_LIST] = 1;
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: Multicast address list loading %s.\n", dev->name,
adapter->irx_pcb.data.failed ? "failed" : "succeeded");
break;
/*
* Station address setting
*/
case CMD_SET_ADDRESS_RESPONSE:
adapter->got[CMD_SET_STATION_ADDRESS] = 1;
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: Ethernet address setting %s.\n", dev->name,
adapter->irx_pcb.data.failed ? "failed" : "succeeded");
break;
/*
* received board statistics
*/
case CMD_NETWORK_STATISTICS_RESPONSE:
adapter->stats.rx_packets += adapter->irx_pcb.data.netstat.tot_recv;
adapter->stats.tx_packets += adapter->irx_pcb.data.netstat.tot_xmit;
adapter->stats.rx_crc_errors += adapter->irx_pcb.data.netstat.err_CRC;
adapter->stats.rx_frame_errors += adapter->irx_pcb.data.netstat.err_align;
adapter->stats.rx_fifo_errors += adapter->irx_pcb.data.netstat.err_ovrrun;
adapter->stats.rx_over_errors += adapter->irx_pcb.data.netstat.err_res;
adapter->got[CMD_NETWORK_STATISTICS] = 1;
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: interrupt - statistics response received\n", dev->name);
break;
/*
* sent a packet
*/
case CMD_TRANSMIT_PACKET_COMPLETE:
if (elp_debug >= 3)
printk(KERN_DEBUG "%s: interrupt - packet sent\n", dev->name);
if (!netif_running(dev))
break;
switch (adapter->irx_pcb.data.xmit_resp.c_stat) {
case 0xffff:
adapter->stats.tx_aborted_errors++;
printk(KERN_INFO "%s: transmit timed out, network cable problem?\n", dev->name);
break;
case 0xfffe:
adapter->stats.tx_fifo_errors++;
printk(KERN_INFO "%s: transmit timed out, FIFO underrun\n", dev->name);
break;
}
netif_wake_queue(dev);
break;
/*
* some unknown PCB
*/
default:
printk(KERN_DEBUG "%s: unknown PCB received - %2.2x\n", dev->name, adapter->irx_pcb.command);
break;
}
} else {
printk(KERN_WARNING "%s: failed to read PCB on interrupt\n", dev->name);
adapter_reset(dev);
}
}
} while (icount++ < 5 && (inb_status(dev->base_addr) & (ACRF | DONE)));
prime_rx(dev);
/*
* indicate no longer in interrupt routine
*/
spin_unlock(&adapter->lock);
return IRQ_HANDLED;
}
static int elp_open(struct net_device *dev)
{
elp_device *adapter = netdev_priv(dev);
int retval;
if (elp_debug >= 3)
pr_debug("%s: request to open device\n", dev->name);
if (adapter == NULL) {
pr_err("%s: Opening a non-existent physical device\n", dev->name);
return -EAGAIN;
}
outb_control(0, dev);
inb_command(dev->base_addr);
adapter_reset(dev);
adapter->rx_active = 0;
adapter->busy = 0;
adapter->send_pcb_semaphore = 0;
adapter->rx_backlog.in = 0;
adapter->rx_backlog.out = 0;
spin_lock_init(&adapter->lock);
if ((retval = request_irq(dev->irq, elp_interrupt, 0, dev->name, dev))) {
pr_err("%s: could not allocate IRQ%d\n", dev->name, dev->irq);
return retval;
}
if ((retval = request_dma(dev->dma, dev->name))) {
free_irq(dev->irq, dev);
pr_err("%s: could not allocate DMA%d channel\n", dev->name, dev->dma);
return retval;
}
adapter->dma_buffer = (void *) dma_mem_alloc(DMA_BUFFER_SIZE);
if (!adapter->dma_buffer) {
pr_err("%s: could not allocate DMA buffer\n", dev->name);
free_dma(dev->dma);
free_irq(dev->irq, dev);
return -ENOMEM;
}
adapter->dmaing = 0;
outb_control(CMDE, dev);
if (elp_debug >= 3)
pr_debug("%s: sending 3c505 memory configuration command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_ADAPTER_MEMORY;
adapter->tx_pcb.data.memconf.cmd_q = 10;
adapter->tx_pcb.data.memconf.rcv_q = 20;
adapter->tx_pcb.data.memconf.mcast = 10;
adapter->tx_pcb.data.memconf.frame = 20;
adapter->tx_pcb.data.memconf.rcv_b = 20;
adapter->tx_pcb.data.memconf.progs = 0;
adapter->tx_pcb.length = sizeof(struct Memconf);
adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
pr_err("%s: couldn't send memory configuration command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_CONFIGURE_ADAPTER_MEMORY] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
if (elp_debug >= 3)
pr_debug("%s: sending 82586 configure command\n", dev->name);
adapter->tx_pcb.command = CMD_CONFIGURE_82586;
adapter->tx_pcb.data.configure = NO_LOOPBACK | RECV_BROAD;
adapter->tx_pcb.length = 2;
adapter->got[CMD_CONFIGURE_82586] = 0;
if (!send_pcb(dev, &adapter->tx_pcb))
pr_err("%s: couldn't send 82586 configure command\n", dev->name);
else {
unsigned long timeout = jiffies + TIMEOUT;
while (adapter->got[CMD_CONFIGURE_82586] == 0 && time_before(jiffies, timeout));
if (time_after_eq(jiffies, timeout))
TIMEOUT_MSG(__LINE__);
}
prime_rx(dev);
if (elp_debug >= 3)
pr_debug("%s: %d receive PCBs active\n", dev->name, adapter->rx_active);
netif_start_queue(dev);
return 0;
}