/**
* qib_eeprom_read - receives bytes from the eeprom via I2C
* @dd: the qlogic_ib device
* @eeprom_offset: address to read from
* @buffer: where to store result
* @len: number of bytes to receive
*/
int qib_eeprom_read(struct qib_devdata *dd, u8 eeprom_offset,
void *buff, int len)
{
int ret;
ret = mutex_lock_interruptible(&dd->eep_lock);
if (!ret) {
ret = qib_twsi_reset(dd);
if (ret)
qib_dev_err(dd, "EEPROM Reset for read failed\n");
else
ret = qib_twsi_blk_rd(dd, dd->twsi_eeprom_dev,
eeprom_offset, buff, len);
mutex_unlock(&dd->eep_lock);
}
return ret;
}
static int qsfp_read(struct qib_pportdata *ppd, int addr, void *bp, int len)
{
struct qib_devdata *dd = ppd->dd;
u32 out, mask;
int ret, cnt, pass = 0;
int stuck = 0;
u8 *buff = bp;
qib_cdbg(VERBOSE, "Grabbing Mutex for QSFP in %d:%d\n", dd->unit,
ppd->port);
ret = mutex_lock_interruptible(&dd->eep_lock);
if (ret)
goto no_unlock;
if (dd->twsi_eeprom_dev == QIB_TWSI_NO_DEV) {
qib_dbg("QSFP read on board without QSFP\n");
ret = -ENXIO;
goto bail;
}
/*
* We presume, if we are called at all, that this board has
* QSFP. This is on the same i2c chain as the legacy parts,
* but only responds if the module is selected via GPIO pins.
* Further, there are very long setup and hold requirements
* on MODSEL.
*/
mask = QSFP_GPIO_MOD_SEL_N | QSFP_GPIO_MOD_RST_N | QSFP_GPIO_LP_MODE;
out = QSFP_GPIO_MOD_RST_N | QSFP_GPIO_LP_MODE;
if (ppd->hw_pidx) {
mask <<= QSFP_GPIO_PORT2_SHIFT;
out <<= QSFP_GPIO_PORT2_SHIFT;
}
dd->f_gpio_mod(dd, out, mask, mask);
/*
* Module could take up to 2 Msec to respond to MOD_SEL, and there
* is no way to tell if it is ready, so we must wait.
*/
msleep(2);
/* Make sure TWSI bus is in sane state. */
ret = qib_twsi_reset(dd);
if (ret) {
qib_dev_porterr(dd, ppd->port,
"QSFP interface Reset for read failed\n");
ret = -EIO;
stuck = 1;
goto deselect;
}
/* All QSFP modules are at A0 */
cnt = 0;
while (cnt < len) {
unsigned in_page;
int wlen = len - cnt;
in_page = addr % QSFP_PAGESIZE;
if ((in_page + wlen) > QSFP_PAGESIZE)
wlen = QSFP_PAGESIZE - in_page;
ret = qib_twsi_blk_rd(dd, QSFP_DEV, addr, buff + cnt, wlen);
/* Some QSFP's fail first try. Retry as experiment */
if (ret && cnt == 0 && ++pass < QSFP_MAX_RETRY)
continue;
if (ret) {
/* qib_twsi_blk_rd() 1 for error, else 0 */
ret = -EIO;
goto deselect;
}
addr += wlen;
cnt += wlen;
}
ret = cnt;
deselect:
/*
* Module could take up to 10 uSec after transfer before
* ready to respond to MOD_SEL negation, and there is no way
* to tell if it is ready, so we must wait.
*/
udelay(10);
/* set QSFP MODSEL, RST. LP all high */
dd->f_gpio_mod(dd, mask, mask, mask);
/*
* Module could take up to 2 Msec to respond to MOD_SEL
* going away, and there is no way to tell if it is ready.
* so we must wait.
*/
if (stuck)
qib_dev_err(dd, "QSFP interface bus stuck non-idle\n");
if (pass >= QSFP_MAX_RETRY && ret)
qib_dev_porterr(dd, ppd->port, "QSFP failed even retrying\n");
else if (pass)
qib_dev_porterr(dd, ppd->port, "QSFP retries: %d\n", pass);
msleep(2);
bail:
mutex_unlock(&dd->eep_lock);
qib_cdbg(VERBOSE, "Released Mutex for QSFP %d:%d, ret %d\n", dd->unit,
ppd->port, ret);
no_unlock:
return ret;
}
/**
* qib_update_eeprom_log - copy active-time and error counters to eeprom
* @dd: the qlogic_ib device
*
* Although the time is kept as seconds in the qib_devdata struct, it is
* rounded to hours for re-write, as we have only 16 bits in EEPROM.
* First-cut code reads whole (expected) struct qib_flash, modifies,
* re-writes. Future direction: read/write only what we need, assuming
* that the EEPROM had to have been "good enough" for driver init, and
* if not, we aren't making it worse.
*
*/
int qib_update_eeprom_log(struct qib_devdata *dd)
{
void *buf;
struct qib_flash *ifp;
int len, hi_water;
uint32_t new_time, new_hrs;
u8 csum;
int ret, idx;
unsigned long flags;
/* first, check if we actually need to do anything. */
ret = 0;
for (idx = 0; idx < QIB_EEP_LOG_CNT; ++idx) {
if (dd->eep_st_new_errs[idx]) {
ret = 1;
break;
}
}
new_time = atomic_read(&dd->active_time);
if (ret == 0 && new_time < 3600)
goto bail;
/*
* The quick-check above determined that there is something worthy
* of logging, so get current contents and do a more detailed idea.
* read full flash, not just currently used part, since it may have
* been written with a newer definition
*/
len = sizeof(struct qib_flash);
buf = vmalloc(len);
ret = 1;
if (!buf) {
qib_dev_err(dd, "Couldn't allocate memory to read %u "
"bytes from eeprom for logging\n", len);
goto bail;
}
/* Grab semaphore and read current EEPROM. If we get an
* error, let go, but if not, keep it until we finish write.
*/
ret = mutex_lock_interruptible(&dd->eep_lock);
if (ret) {
qib_dev_err(dd, "Unable to acquire EEPROM for logging\n");
goto free_bail;
}
ret = qib_twsi_blk_rd(dd, dd->twsi_eeprom_dev, 0, buf, len);
if (ret) {
mutex_unlock(&dd->eep_lock);
qib_dev_err(dd, "Unable read EEPROM for logging\n");
goto free_bail;
}
ifp = (struct qib_flash *)buf;
csum = flash_csum(ifp, 0);
if (csum != ifp->if_csum) {
mutex_unlock(&dd->eep_lock);
qib_dev_err(dd, "EEPROM cks err (0x%02X, S/B 0x%02X)\n",
csum, ifp->if_csum);
ret = 1;
goto free_bail;
}
hi_water = 0;
spin_lock_irqsave(&dd->eep_st_lock, flags);
for (idx = 0; idx < QIB_EEP_LOG_CNT; ++idx) {
int new_val = dd->eep_st_new_errs[idx];
if (new_val) {
/*
* If we have seen any errors, add to EEPROM values
* We need to saturate at 0xFF (255) and we also
* would need to adjust the checksum if we were
* trying to minimize EEPROM traffic
* Note that we add to actual current count in EEPROM,
* in case it was altered while we were running.
*/
new_val += ifp->if_errcntp[idx];
if (new_val > 0xFF)
new_val = 0xFF;
if (ifp->if_errcntp[idx] != new_val) {
ifp->if_errcntp[idx] = new_val;
hi_water = offsetof(struct qib_flash,
if_errcntp) + idx;
}
/*
* update our shadow (used to minimize EEPROM
* traffic), to match what we are about to write.
*/
dd->eep_st_errs[idx] = new_val;
dd->eep_st_new_errs[idx] = 0;
}
}
