C++ (Cpp) rate_control_rate_dec 예제들

예제 #1

파일: rc80211_simple.c 프로젝트: acassis/emlinux-ssd1935

static void rate_control_simple_tx_status(void *priv, struct net_device *dev,
					  struct sk_buff *skb,
					  struct ieee80211_tx_status *status)
{
	struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
	struct sta_info *sta;
	struct sta_rate_control *srctrl;

	sta = sta_info_get(local, hdr->addr1);

	if (!sta)
	    return;

	srctrl = sta->rate_ctrl_priv;
	srctrl->tx_num_xmit++;
	if (status->excessive_retries) {
		srctrl->tx_num_failures++;
		sta->tx_retry_failed++;
		sta->tx_num_consecutive_failures++;
		sta->tx_num_mpdu_fail++;
	} else {
		sta->last_ack_rssi[0] = sta->last_ack_rssi[1];
		sta->last_ack_rssi[1] = sta->last_ack_rssi[2];
		sta->last_ack_rssi[2] = status->ack_signal;
		sta->tx_num_consecutive_failures = 0;
		sta->tx_num_mpdu_ok++;
	}
	sta->tx_retry_count += status->retry_count;
	sta->tx_num_mpdu_fail += status->retry_count;

	if (time_after(jiffies,
		       srctrl->last_rate_change + RATE_CONTROL_INTERVAL) &&
		srctrl->tx_num_xmit > RATE_CONTROL_MIN_TX) {
		u32 per_failed;
		srctrl->last_rate_change = jiffies;

		per_failed = (100 * sta->tx_num_mpdu_fail) /
			(sta->tx_num_mpdu_fail + sta->tx_num_mpdu_ok);
		/* TODO: calculate average per_failed to make adjusting
		 * parameters easier */
#if 0
		if (net_ratelimit()) {
			printk(KERN_DEBUG "MPDU fail=%d ok=%d per_failed=%d\n",
			       sta->tx_num_mpdu_fail, sta->tx_num_mpdu_ok,
			       per_failed);
		}
#endif

		/*
		 * XXX: Make these configurable once we have an
		 * interface to the rate control algorithms
		 */
		if (per_failed > RATE_CONTROL_NUM_DOWN) {
			rate_control_rate_dec(local, sta);
		} else if (per_failed < RATE_CONTROL_NUM_UP) {
			rate_control_rate_inc(local, sta);
		}
		srctrl->tx_avg_rate_sum += status->control.rate->rate;
		srctrl->tx_avg_rate_num++;
		srctrl->tx_num_failures = 0;
		srctrl->tx_num_xmit = 0;
	} else if (sta->tx_num_consecutive_failures >=
		   RATE_CONTROL_EMERG_DEC) {
		rate_control_rate_dec(local, sta);
	}

	if (srctrl->avg_rate_update + 60 * HZ < jiffies) {
		srctrl->avg_rate_update = jiffies;
		if (srctrl->tx_avg_rate_num > 0) {
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
			DECLARE_MAC_BUF(mac);
			printk(KERN_DEBUG "%s: STA %s Average rate: "
			       "%d (%d/%d)\n",
			       dev->name, print_mac(mac, sta->addr),
			       srctrl->tx_avg_rate_sum /
			       srctrl->tx_avg_rate_num,
			       srctrl->tx_avg_rate_sum,
			       srctrl->tx_avg_rate_num);
#endif /* CONFIG_MAC80211_VERBOSE_DEBUG */
			srctrl->tx_avg_rate_sum = 0;
			srctrl->tx_avg_rate_num = 0;
		}
	}

	sta_info_put(sta);
}

예제 #2

파일: rc80211_simple.c 프로젝트: 3sOx/asuswrt-merlin

static void rate_control_simple_tx_status(void *priv, struct net_device *dev,
					  struct sk_buff *skb,
					  struct ieee80211_tx_status *status)
{
	struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
	struct sta_info *sta;
	struct sta_rate_control *srctrl;

	sta = sta_info_get(local, hdr->addr1);

	if (!sta)
	    return;

	srctrl = sta->rate_ctrl_priv;
	srctrl->tx_num_xmit++;
	if (status->excessive_retries) {
		sta->antenna_sel_tx = sta->antenna_sel_tx == 1 ? 2 : 1;
		sta->antenna_sel_rx = sta->antenna_sel_rx == 1 ? 2 : 1;
		if (local->sta_antenna_sel == STA_ANTENNA_SEL_SW_CTRL_DEBUG) {
			printk(KERN_DEBUG "%s: " MAC_FMT " TX antenna --> %d "
			       "RX antenna --> %d (@%lu)\n",
			       dev->name, MAC_ARG(hdr->addr1),
			       sta->antenna_sel_tx, sta->antenna_sel_rx, jiffies);
		}
		srctrl->tx_num_failures++;
		sta->tx_retry_failed++;
		sta->tx_num_consecutive_failures++;
		sta->tx_num_mpdu_fail++;
	} else {
		sta->last_ack_rssi[0] = sta->last_ack_rssi[1];
		sta->last_ack_rssi[1] = sta->last_ack_rssi[2];
		sta->last_ack_rssi[2] = status->ack_signal;
		sta->tx_num_consecutive_failures = 0;
		sta->tx_num_mpdu_ok++;
	}
	sta->tx_retry_count += status->retry_count;
	sta->tx_num_mpdu_fail += status->retry_count;

	if (time_after(jiffies,
		       srctrl->last_rate_change + RATE_CONTROL_INTERVAL) &&
		srctrl->tx_num_xmit > RATE_CONTROL_MIN_TX) {
		u32 per_failed;
		srctrl->last_rate_change = jiffies;

		per_failed = (100 * sta->tx_num_mpdu_fail) /
			(sta->tx_num_mpdu_fail + sta->tx_num_mpdu_ok);
		/* TODO: calculate average per_failed to make adjusting
		 * parameters easier */
#if 0
		if (net_ratelimit()) {
			printk(KERN_DEBUG "MPDU fail=%d ok=%d per_failed=%d\n",
			       sta->tx_num_mpdu_fail, sta->tx_num_mpdu_ok,
			       per_failed);
		}
#endif

		if (per_failed > local->rate_ctrl_num_down) {
			rate_control_rate_dec(local, sta);
		} else if (per_failed < local->rate_ctrl_num_up) {
			rate_control_rate_inc(local, sta);
		}
		srctrl->tx_avg_rate_sum += status->control.rate->rate;
		srctrl->tx_avg_rate_num++;
		srctrl->tx_num_failures = 0;
		srctrl->tx_num_xmit = 0;
	} else if (sta->tx_num_consecutive_failures >=
		   RATE_CONTROL_EMERG_DEC) {
		rate_control_rate_dec(local, sta);
	}

	if (srctrl->avg_rate_update + 60 * HZ < jiffies) {
		srctrl->avg_rate_update = jiffies;
		if (srctrl->tx_avg_rate_num > 0) {
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
			printk(KERN_DEBUG "%s: STA " MAC_FMT " Average rate: "
			       "%d (%d/%d)\n",
			       dev->name, MAC_ARG(sta->addr),
			       srctrl->tx_avg_rate_sum /
			       srctrl->tx_avg_rate_num,
			       srctrl->tx_avg_rate_sum,
			       srctrl->tx_avg_rate_num);
#endif /* CONFIG_MAC80211_VERBOSE_DEBUG */
			srctrl->tx_avg_rate_sum = 0;
			srctrl->tx_avg_rate_num = 0;
		}
	}

	sta_info_put(sta);
}