void Plane::init_ardupilot()
{
// initialise serial port
serial_manager.init_console();
cliSerial->printf_P(PSTR("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n"),
hal.util->available_memory());
//
// Check the EEPROM format version before loading any parameters from EEPROM
//
load_parameters();
if (g.hil_mode == 1) {
// set sensors to HIL mode
ins.set_hil_mode();
compass.set_hil_mode();
barometer.set_hil_mode();
}
#if CONFIG_HAL_BOARD == HAL_BOARD_PX4
// this must be before BoardConfig.init() so if
// BRD_SAFETYENABLE==0 then we don't have safety off yet
for (uint8_t tries=0; tries<10; tries++) {
if (setup_failsafe_mixing()) {
break;
}
hal.scheduler->delay(10);
}
#endif
BoardConfig.init();
// initialise serial ports
serial_manager.init();
// allow servo set on all channels except first 4
ServoRelayEvents.set_channel_mask(0xFFF0);
set_control_channels();
// keep a record of how many resets have happened. This can be
// used to detect in-flight resets
g.num_resets.set_and_save(g.num_resets+1);
// init baro before we start the GCS, so that the CLI baro test works
barometer.init();
// initialise rangefinder
init_rangefinder();
// initialise battery monitoring
battery.init();
// init the GCS
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_Console, 0);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
usb_connected = true;
check_usb_mux();
// setup serial port for telem1
gcs[1].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
#if MAVLINK_COMM_NUM_BUFFERS > 2
// setup serial port for telem2
gcs[2].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 1);
#endif
#if MAVLINK_COMM_NUM_BUFFERS > 3
// setup serial port for fourth telemetry port (not used by default)
gcs[3].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 2);
#endif
// setup frsky
#if FRSKY_TELEM_ENABLED == ENABLED
frsky_telemetry.init(serial_manager);
#endif
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
#if CONFIG_HAL_BOARD == HAL_BOARD_APM1
apm1_adc.Init(); // APM ADC library initialization
#endif
// initialise airspeed sensor
airspeed.init();
if (g.compass_enabled==true) {
if (!compass.init() || !compass.read()) {
cliSerial->println_P(PSTR("Compass initialisation failed!"));
g.compass_enabled = false;
} else {
ahrs.set_compass(&compass);
}
}
#if OPTFLOW == ENABLED
// make optflow available to libraries
ahrs.set_optflow(&optflow);
#endif
// Register mavlink_delay_cb, which will run anytime you have
// more than 5ms remaining in your call to hal.scheduler->delay
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
// give AHRS the airspeed sensor
ahrs.set_airspeed(&airspeed);
// GPS Initialization
gps.init(&DataFlash, serial_manager);
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up the timer libs
relay.init();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(serial_manager);
#endif
#if FENCE_TRIGGERED_PIN > 0
hal.gpio->pinMode(FENCE_TRIGGERED_PIN, HAL_GPIO_OUTPUT);
hal.gpio->write(FENCE_TRIGGERED_PIN, 0);
#endif
/*
* setup the 'main loop is dead' check. Note that this relies on
* the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
#if CLI_ENABLED == ENABLED
if (g.cli_enabled == 1) {
const prog_char_t *msg = PSTR("\nPress ENTER 3 times to start interactive setup\n");
cliSerial->println_P(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println_P(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println_P(msg);
}
}
#endif // CLI_ENABLED
startup_ground();
Log_Write_Startup(TYPE_GROUNDSTART_MSG);
// choose the nav controller
set_nav_controller();
set_mode((FlightMode)g.initial_mode.get());
// set the correct flight mode
// ---------------------------
reset_control_switch();
// initialise sensor
#if OPTFLOW == ENABLED
optflow.init();
#endif
}
void Copter::init_ardupilot()
{
if (!hal.gpio->usb_connected()) {
// USB is not connected, this means UART0 may be a Xbee, with
// its darned bricking problem. We can't write to it for at
// least one second after powering up. Simplest solution for
// now is to delay for 1 second. Something more elegant may be
// added later
delay(1000);
}
// initialise serial port
serial_manager.init_console();
// init vehicle capabilties
init_capabilities();
cliSerial->printf("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n",
(unsigned)hal.util->available_memory());
//
// Report firmware version code expect on console (check of actual EEPROM format version is done in load_parameters function)
//
report_version();
// load parameters from EEPROM
load_parameters();
BoardConfig.init();
// initialise serial port
serial_manager.init();
// init EPM cargo gripper
#if EPM_ENABLED == ENABLED
epm.init();
#endif
// initialise notify system
// disable external leds if epm is enabled because of pin conflict on the APM
notify.init(true);
// initialise battery monitor
battery.init();
// Init RSSI
rssi.init();
barometer.init();
// Register the mavlink service callback. This will run
// anytime there are more than 5ms remaining in a call to
// hal.scheduler->delay.
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
ap.usb_connected = true;
check_usb_mux();
// init the GCS connected to the console
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_Console, 0);
// init telemetry port
gcs[1].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
// setup serial port for telem2
gcs[2].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 1);
// setup serial port for fourth telemetry port (not used by default)
gcs[3].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 2);
#if FRSKY_TELEM_ENABLED == ENABLED
// setup frsky
frsky_telemetry.init(serial_manager);
#endif
// identify ourselves correctly with the ground station
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
GCS_MAVLINK::set_dataflash(&DataFlash);
// update motor interlock state
update_using_interlock();
#if FRAME_CONFIG == HELI_FRAME
// trad heli specific initialisation
heli_init();
#endif
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up motors and output to escs
// initialise which outputs Servo and Relay events can use
ServoRelayEvents.set_channel_mask(~motors.get_motor_mask());
relay.init();
/*
* setup the 'main loop is dead' check. Note that this relies on
* the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
// Do GPS init
gps.init(&DataFlash, serial_manager);
if(g.compass_enabled)
init_compass();
#if OPTFLOW == ENABLED
// make optflow available to AHRS
ahrs.set_optflow(&optflow);
#endif
// init Location class
Location_Class::set_ahrs(&ahrs);
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
Location_Class::set_terrain(&terrain);
wp_nav.set_terrain(&terrain);
#endif
pos_control.set_dt(MAIN_LOOP_SECONDS);
// init the optical flow sensor
init_optflow();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(&DataFlash, serial_manager);
#endif
#if PRECISION_LANDING == ENABLED
// initialise precision landing
init_precland();
#endif
#ifdef USERHOOK_INIT
USERHOOK_INIT
#endif
#if CLI_ENABLED == ENABLED
if (g.cli_enabled) {
const char *msg = "\nPress ENTER 3 times to start interactive setup\n";
cliSerial->println(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println(msg);
}
}
#endif // CLI_ENABLED
#if HIL_MODE != HIL_MODE_DISABLED
while (barometer.get_last_update() == 0) {
// the barometer begins updating when we get the first
// HIL_STATE message
gcs_send_text(MAV_SEVERITY_WARNING, "Waiting for first HIL_STATE message");
delay(1000);
}
// set INS to HIL mode
ins.set_hil_mode();
#endif
// read Baro pressure at ground
//-----------------------------
init_barometer(true);
// initialise sonar
#if CONFIG_SONAR == ENABLED
init_sonar();
#endif
// initialise AP_RPM library
rpm_sensor.init();
// initialise mission library
mission.init();
// initialise the flight mode and aux switch
// ---------------------------
reset_control_switch();
init_aux_switches();
startup_INS_ground();
// set landed flags
set_land_complete(true);
set_land_complete_maybe(true);
// we don't want writes to the serial port to cause us to pause
// mid-flight, so set the serial ports non-blocking once we are
// ready to fly
serial_manager.set_blocking_writes_all(false);
// enable CPU failsafe
failsafe_enable();
ins.set_raw_logging(should_log(MASK_LOG_IMU_RAW));
ins.set_dataflash(&DataFlash);
cliSerial->print("\nReady to FLY ");
// flag that initialisation has completed
ap.initialised = true;
}
void Rover::init_ardupilot()
{
// initialise console serial port
serial_manager.init_console();
cliSerial->printf("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n",
hal.util->available_memory());
//
// Check the EEPROM format version before loading any parameters from EEPROM.
//
load_parameters();
BoardConfig.init();
// initialise serial ports
serial_manager.init();
ServoRelayEvents.set_channel_mask(0xFFF0);
set_control_channels();
battery.init();
// keep a record of how many resets have happened. This can be
// used to detect in-flight resets
g.num_resets.set_and_save(g.num_resets+1);
// init baro before we start the GCS, so that the CLI baro test works
barometer.init();
// init the GCS
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_Console, 0);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
usb_connected = true;
check_usb_mux();
// setup serial port for telem1
gcs[1].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
// setup serial port for telem2
gcs[2].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 1);
// setup serial port for fourth telemetry port (not used by default)
gcs[3].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 2);
// setup frsky telemetry
#if FRSKY_TELEM_ENABLED == ENABLED
frsky_telemetry.init(serial_manager);
#endif
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
// Register mavlink_delay_cb, which will run anytime you have
// more than 5ms remaining in your call to hal.scheduler->delay
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
if (g.compass_enabled==true) {
if (!compass.init()|| !compass.read()) {
cliSerial->println("Compass initialisation failed!");
g.compass_enabled = false;
} else {
ahrs.set_compass(&compass);
//compass.get_offsets(); // load offsets to account for airframe magnetic interference
}
}
// initialise sonar
init_sonar();
// and baro for EKF
init_barometer();
// Do GPS init
gps.init(&DataFlash, serial_manager);
rc_override_active = hal.rcin->set_overrides(rc_override, 8);
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up the timer libs
relay.init();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(serial_manager);
#endif
/*
setup the 'main loop is dead' check. Note that this relies on
the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
#if CLI_ENABLED == ENABLED
// If the switch is in 'menu' mode, run the main menu.
//
// Since we can't be sure that the setup or test mode won't leave
// the system in an odd state, we don't let the user exit the top
// menu; they must reset in order to fly.
//
if (g.cli_enabled == 1) {
const char *msg = "\nPress ENTER 3 times to start interactive setup\n";
cliSerial->println(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println(msg);
}
}
#endif
init_capabilities();
startup_ground();
set_mode((enum mode)g.initial_mode.get());
// set the correct flight mode
// ---------------------------
reset_control_switch();
}
// do_aux_switch_function - implement the function invoked by the ch7 or ch8 switch
void Copter::do_aux_switch_function(int8_t ch_function, uint8_t ch_flag)
{
switch(ch_function) {
case AUXSW_FLIP:
// flip if switch is on, positive throttle and we're actually flying
if (ch_flag == AUX_SWITCH_HIGH) {
set_mode(FLIP, MODE_REASON_TX_COMMAND);
}
break;
case AUXSW_SIMPLE_MODE:
// low = simple mode off, middle or high position turns simple mode on
set_simple_mode(ch_flag == AUX_SWITCH_HIGH || ch_flag == AUX_SWITCH_MIDDLE);
break;
case AUXSW_SUPERSIMPLE_MODE:
// low = simple mode off, middle = simple mode, high = super simple mode
set_simple_mode(ch_flag);
break;
case AUXSW_RTL:
if (ch_flag == AUX_SWITCH_HIGH) {
// engage RTL (if not possible we remain in current flight mode)
set_mode(RTL, MODE_REASON_TX_COMMAND);
} else {
// return to flight mode switch's flight mode if we are currently in RTL
if (control_mode == RTL) {
reset_control_switch();
}
}
break;
case AUXSW_SAVE_TRIM:
if ((ch_flag == AUX_SWITCH_HIGH) && (control_mode <= ACRO) && (channel_throttle->get_control_in() == 0)) {
save_trim();
}
break;
case AUXSW_SAVE_WP:
// save waypoint when switch is brought high
if (ch_flag == AUX_SWITCH_HIGH) {
// do not allow saving new waypoints while we're in auto or disarmed
if (control_mode == AUTO || !motors.armed()) {
return;
}
// do not allow saving the first waypoint with zero throttle
if ((mission.num_commands() == 0) && (channel_throttle->get_control_in() == 0)) {
return;
}
// create new mission command
AP_Mission::Mission_Command cmd = {};
// if the mission is empty save a takeoff command
if (mission.num_commands() == 0) {
// set our location ID to 16, MAV_CMD_NAV_WAYPOINT
cmd.id = MAV_CMD_NAV_TAKEOFF;
cmd.content.location.options = 0;
cmd.p1 = 0;
cmd.content.location.lat = 0;
cmd.content.location.lng = 0;
cmd.content.location.alt = MAX(current_loc.alt,100);
// use the current altitude for the target alt for takeoff.
// only altitude will matter to the AP mission script for takeoff.
if (mission.add_cmd(cmd)) {
// log event
Log_Write_Event(DATA_SAVEWP_ADD_WP);
}
}
// set new waypoint to current location
cmd.content.location = current_loc;
// if throttle is above zero, create waypoint command
if (channel_throttle->get_control_in() > 0) {
cmd.id = MAV_CMD_NAV_WAYPOINT;
} else {
// with zero throttle, create LAND command
cmd.id = MAV_CMD_NAV_LAND;
}
// save command
if (mission.add_cmd(cmd)) {
// log event
Log_Write_Event(DATA_SAVEWP_ADD_WP);
}
}
break;
case AUXSW_CAMERA_TRIGGER:
#if CAMERA == ENABLED
if (ch_flag == AUX_SWITCH_HIGH) {
do_take_picture();
}
#endif
break;
case AUXSW_RANGEFINDER:
// enable or disable the rangefinder
#if RANGEFINDER_ENABLED == ENABLED
if ((ch_flag == AUX_SWITCH_HIGH) && (rangefinder.num_sensors() >= 1)) {
rangefinder_state.enabled = true;
} else {
rangefinder_state.enabled = false;
}
#endif
break;
case AUXSW_FENCE:
#if AC_FENCE == ENABLED
// enable or disable the fence
if (ch_flag == AUX_SWITCH_HIGH) {
fence.enable(true);
Log_Write_Event(DATA_FENCE_ENABLE);
} else {
fence.enable(false);
Log_Write_Event(DATA_FENCE_DISABLE);
}
#endif
break;
case AUXSW_ACRO_TRAINER:
switch(ch_flag) {
case AUX_SWITCH_LOW:
g.acro_trainer = ACRO_TRAINER_DISABLED;
Log_Write_Event(DATA_ACRO_TRAINER_DISABLED);
break;
case AUX_SWITCH_MIDDLE:
g.acro_trainer = ACRO_TRAINER_LEVELING;
Log_Write_Event(DATA_ACRO_TRAINER_LEVELING);
break;
case AUX_SWITCH_HIGH:
g.acro_trainer = ACRO_TRAINER_LIMITED;
Log_Write_Event(DATA_ACRO_TRAINER_LIMITED);
break;
}
break;
case AUXSW_GRIPPER:
#if GRIPPER_ENABLED == ENABLED
switch(ch_flag) {
case AUX_SWITCH_LOW:
g2.gripper.release();
Log_Write_Event(DATA_GRIPPER_RELEASE);
break;
case AUX_SWITCH_HIGH:
g2.gripper.grab();
Log_Write_Event(DATA_GRIPPER_GRAB);
break;
}
#endif
break;
case AUXSW_SPRAYER:
#if SPRAYER == ENABLED
sprayer.run(ch_flag == AUX_SWITCH_HIGH);
// if we are disarmed the pilot must want to test the pump
sprayer.test_pump((ch_flag == AUX_SWITCH_HIGH) && !motors.armed());
#endif
break;
case AUXSW_AUTO:
if (ch_flag == AUX_SWITCH_HIGH) {
set_mode(AUTO, MODE_REASON_TX_COMMAND);
} else {
// return to flight mode switch's flight mode if we are currently in AUTO
if (control_mode == AUTO) {
reset_control_switch();
}
}
break;
case AUXSW_AUTOTUNE:
#if AUTOTUNE_ENABLED == ENABLED
// turn on auto tuner
switch(ch_flag) {
case AUX_SWITCH_LOW:
case AUX_SWITCH_MIDDLE:
// restore flight mode based on flight mode switch position
if (control_mode == AUTOTUNE) {
reset_control_switch();
}
break;
case AUX_SWITCH_HIGH:
// start an autotuning session
set_mode(AUTOTUNE, MODE_REASON_TX_COMMAND);
break;
}
#endif
break;
case AUXSW_LAND:
if (ch_flag == AUX_SWITCH_HIGH) {
set_mode(LAND, MODE_REASON_TX_COMMAND);
} else {
// return to flight mode switch's flight mode if we are currently in LAND
if (control_mode == LAND) {
reset_control_switch();
}
}
break;
case AUXSW_PARACHUTE_ENABLE:
#if PARACHUTE == ENABLED
// Parachute enable/disable
parachute.enabled(ch_flag == AUX_SWITCH_HIGH);
#endif
break;
case AUXSW_PARACHUTE_RELEASE:
#if PARACHUTE == ENABLED
if (ch_flag == AUX_SWITCH_HIGH) {
parachute_manual_release();
}
#endif
break;
case AUXSW_PARACHUTE_3POS:
#if PARACHUTE == ENABLED
// Parachute disable, enable, release with 3 position switch
switch (ch_flag) {
case AUX_SWITCH_LOW:
parachute.enabled(false);
Log_Write_Event(DATA_PARACHUTE_DISABLED);
break;
case AUX_SWITCH_MIDDLE:
parachute.enabled(true);
Log_Write_Event(DATA_PARACHUTE_ENABLED);
break;
case AUX_SWITCH_HIGH:
parachute.enabled(true);
parachute_manual_release();
break;
}
#endif
break;
case AUXSW_MISSION_RESET:
if (ch_flag == AUX_SWITCH_HIGH) {
mission.reset();
}
break;
case AUXSW_ATTCON_FEEDFWD:
// enable or disable feed forward
attitude_control.bf_feedforward(ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_ATTCON_ACCEL_LIM:
// enable or disable accel limiting by restoring defaults
attitude_control.accel_limiting(ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_RETRACT_MOUNT:
#if MOUNT == ENABLE
switch (ch_flag) {
case AUX_SWITCH_HIGH:
camera_mount.set_mode(MAV_MOUNT_MODE_RETRACT);
break;
case AUX_SWITCH_LOW:
camera_mount.set_mode_to_default();
break;
}
#endif
break;
case AUXSW_RELAY:
ServoRelayEvents.do_set_relay(0, ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_RELAY2:
ServoRelayEvents.do_set_relay(1, ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_RELAY3:
ServoRelayEvents.do_set_relay(2, ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_RELAY4:
ServoRelayEvents.do_set_relay(3, ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_LANDING_GEAR:
switch (ch_flag) {
case AUX_SWITCH_LOW:
landinggear.set_cmd_mode(LandingGear_Deploy);
break;
case AUX_SWITCH_MIDDLE:
landinggear.set_cmd_mode(LandingGear_Auto);
break;
case AUX_SWITCH_HIGH:
landinggear.set_cmd_mode(LandingGear_Retract);
break;
}
break;
case AUXSW_LOST_COPTER_SOUND:
switch (ch_flag) {
case AUX_SWITCH_HIGH:
AP_Notify::flags.vehicle_lost = true;
break;
case AUX_SWITCH_LOW:
AP_Notify::flags.vehicle_lost = false;
break;
}
break;
case AUXSW_MOTOR_ESTOP:
// Turn on Emergency Stop logic when channel is high
set_motor_emergency_stop(ch_flag == AUX_SWITCH_HIGH);
break;
case AUXSW_MOTOR_INTERLOCK:
// Turn on when above LOW, because channel will also be used for speed
// control signal in tradheli
ap.motor_interlock_switch = (ch_flag == AUX_SWITCH_HIGH || ch_flag == AUX_SWITCH_MIDDLE);
break;
case AUXSW_BRAKE:
// brake flight mode
if (ch_flag == AUX_SWITCH_HIGH) {
set_mode(BRAKE, MODE_REASON_TX_COMMAND);
} else {
// return to flight mode switch's flight mode if we are currently in BRAKE
if (control_mode == BRAKE) {
reset_control_switch();
}
}
break;
case AUXSW_THROW:
// throw flight mode
if (ch_flag == AUX_SWITCH_HIGH) {
set_mode(THROW, MODE_REASON_TX_COMMAND);
} else {
// return to flight mode switch's flight mode if we are currently in throw mode
if (control_mode == THROW) {
reset_control_switch();
}
}
break;
case AUXSW_AVOID_ADSB:
// enable or disable AP_Avoidance
if (ch_flag == AUX_SWITCH_HIGH) {
avoidance_adsb.enable();
Log_Write_Event(DATA_AVOIDANCE_ADSB_ENABLE);
} else {
avoidance_adsb.disable();
Log_Write_Event(DATA_AVOIDANCE_ADSB_DISABLE);
}
break;
case AUXSW_PRECISION_LOITER:
#if PRECISION_LANDING == ENABLED
switch (ch_flag) {
case AUX_SWITCH_HIGH:
set_precision_loiter_enabled(true);
break;
case AUX_SWITCH_LOW:
set_precision_loiter_enabled(false);
break;
}
#endif
break;
case AUXSW_AVOID_PROXIMITY:
#if PROXIMITY_ENABLED == ENABLED
switch (ch_flag) {
case AUX_SWITCH_HIGH:
avoid.proximity_avoidance_enable(true);
Log_Write_Event(DATA_AVOIDANCE_PROXIMITY_ENABLE);
break;
case AUX_SWITCH_LOW:
avoid.proximity_avoidance_enable(false);
Log_Write_Event(DATA_AVOIDANCE_PROXIMITY_DISABLE);
break;
}
#endif
break;
}
}
void Plane::init_ardupilot()
{
// initialise serial port
serial_manager.init_console();
cliSerial->printf("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n",
(unsigned)hal.util->available_memory());
//
// Check the EEPROM format version before loading any parameters from EEPROM
//
load_parameters();
#if HIL_SUPPORT
if (g.hil_mode == 1) {
// set sensors to HIL mode
ins.set_hil_mode();
compass.set_hil_mode();
barometer.set_hil_mode();
}
#endif
set_control_channels();
init_rc_out_main();
#if HAVE_PX4_MIXER
if (!quadplane.enable) {
// this must be before BoardConfig.init() so if
// BRD_SAFETYENABLE==0 then we don't have safety off yet. For
// quadplanes we wait till AP_Motors is initialised
for (uint8_t tries=0; tries<10; tries++) {
if (setup_failsafe_mixing()) {
break;
}
hal.scheduler->delay(10);
}
}
#endif
GCS_MAVLINK::set_dataflash(&DataFlash);
// initialise serial ports
serial_manager.init();
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
// Register mavlink_delay_cb, which will run anytime you have
// more than 5ms remaining in your call to hal.scheduler->delay
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
// setup any board specific drivers
BoardConfig.init();
// allow servo set on all channels except first 4
ServoRelayEvents.set_channel_mask(0xFFF0);
// keep a record of how many resets have happened. This can be
// used to detect in-flight resets
g.num_resets.set_and_save(g.num_resets+1);
// init baro before we start the GCS, so that the CLI baro test works
barometer.init();
// initialise rangefinder
init_rangefinder();
// initialise battery monitoring
battery.init();
rpm_sensor.init();
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
usb_connected = true;
check_usb_mux();
// setup telem slots with serial ports
for (uint8_t i = 1; i < MAVLINK_COMM_NUM_BUFFERS; i++) {
gcs[i].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, i);
}
// setup frsky
#if FRSKY_TELEM_ENABLED == ENABLED
// setup frsky, and pass a number of parameters to the library
frsky_telemetry.init(serial_manager, FIRMWARE_STRING,
MAV_TYPE_FIXED_WING,
&g.fs_batt_voltage, &g.fs_batt_mah);
#endif
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
// initialise airspeed sensor
airspeed.init();
if (g.compass_enabled==true) {
bool compass_ok = compass.init() && compass.read();
#if HIL_SUPPORT
if (g.hil_mode != 0) {
compass_ok = true;
}
#endif
if (!compass_ok) {
cliSerial->println("Compass initialisation failed!");
g.compass_enabled = false;
} else {
ahrs.set_compass(&compass);
}
}
#if OPTFLOW == ENABLED
// make optflow available to libraries
if (optflow.enabled()) {
ahrs.set_optflow(&optflow);
}
#endif
// give AHRS the airspeed sensor
ahrs.set_airspeed(&airspeed);
// GPS Initialization
gps.init(&DataFlash, serial_manager);
init_rc_in(); // sets up rc channels from radio
relay.init();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(&DataFlash, serial_manager);
#endif
#if FENCE_TRIGGERED_PIN > 0
hal.gpio->pinMode(FENCE_TRIGGERED_PIN, HAL_GPIO_OUTPUT);
hal.gpio->write(FENCE_TRIGGERED_PIN, 0);
#endif
/*
* setup the 'main loop is dead' check. Note that this relies on
* the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
#if CLI_ENABLED == ENABLED
if (g.cli_enabled == 1) {
const char *msg = "\nPress ENTER 3 times to start interactive setup\n";
cliSerial->println(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println(msg);
}
}
#endif // CLI_ENABLED
init_capabilities();
quadplane.setup();
startup_ground();
// don't initialise aux rc output until after quadplane is setup as
// that can change initial values of channels
init_rc_out_aux();
// choose the nav controller
set_nav_controller();
set_mode((FlightMode)g.initial_mode.get(), MODE_REASON_UNKNOWN);
// set the correct flight mode
// ---------------------------
reset_control_switch();
// initialise sensor
#if OPTFLOW == ENABLED
if (optflow.enabled()) {
optflow.init();
}
#endif
}
