void rtl8225_rf_init(struct net_device *dev)
{
struct r8180_priv *priv = ieee80211_priv(dev);
int i;
short channel = 1;
u16 brsr;
priv->chan = channel;
rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_ON);
if(priv->card_type == USB)
rtl8225_host_usb_init(dev);
else
rtl8225_host_pci_init(dev);
write_nic_dword(dev, RF_TIMING, 0x000a8008);
brsr = read_nic_word(dev, BRSR);
write_nic_word(dev, BRSR, 0xffff);
#if 0
if(priv->card_8185 == 1){/* version C or B */
if(priv->card_8185_Bversion) /* version B*/
write_nic_dword(dev, RF_PARA, 0x44);
else /* version C */
write_nic_dword(dev, RF_PARA, 0x100044);
}else{ /* version D */
if(priv->enable_gpio0)
write_nic_dword(dev, RF_PARA, 0x20100044);
else /* also USB */
write_nic_dword(dev, RF_PARA, 0x100044);
}
#endif
write_nic_dword(dev, RF_PARA, 0x100044);
#if 1 //0->1
rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
write_nic_byte(dev, CONFIG3, 0x44);
rtl8180_set_mode(dev, EPROM_CMD_NORMAL);
#endif
if(priv->card_type == USB){
rtl8185_rf_pins_enable(dev);
mdelay(1000);
}
write_rtl8225(dev, 0x0, 0x67); mdelay(1);
write_rtl8225(dev, 0x1, 0xfe0); mdelay(1);
write_rtl8225(dev, 0x2, 0x44d); mdelay(1);
write_rtl8225(dev, 0x3, 0x441); mdelay(1);
if(priv->card_type == USB)
write_rtl8225(dev, 0x4, 0x486);
else
write_rtl8225(dev, 0x4, 0x8be);
mdelay(1);
#if 0
}else if(priv->phy_ver == 1){
void rtl8225z2_rf_init(struct net_device *dev)
{
struct r8180_priv *priv = ieee80211_priv(dev);
int i;
short channel = 1;
u16 brsr;
u32 data,addr;
priv->chan = channel;
rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_ON);
if(priv->card_type == USB)
rtl8225_host_usb_init(dev);
else
rtl8225_host_pci_init(dev);
write_nic_dword(dev, RF_TIMING, 0x000a8008);
brsr = read_nic_word(dev, BRSR);
write_nic_word(dev, BRSR, 0xffff);
write_nic_dword(dev, RF_PARA, 0x100044);
#if 1 //0->1
rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
write_nic_byte(dev, CONFIG3, 0x44);
rtl8180_set_mode(dev, EPROM_CMD_NORMAL);
#endif
rtl8185_rf_pins_enable(dev);
// mdelay(1000);
write_rtl8225(dev, 0x0, 0x2bf); mdelay(1);
write_rtl8225(dev, 0x1, 0xee0); mdelay(1);
write_rtl8225(dev, 0x2, 0x44d); mdelay(1);
write_rtl8225(dev, 0x3, 0x441); mdelay(1);
write_rtl8225(dev, 0x4, 0x8c3);mdelay(1);
write_rtl8225(dev, 0x5, 0xc72);mdelay(1);
// }
write_rtl8225(dev, 0x6, 0xe6); mdelay(1);
write_rtl8225(dev, 0x7, ((priv->card_type == USB)? 0x82a : rtl8225_chan[channel])); mdelay(1);
write_rtl8225(dev, 0x8, 0x3f); mdelay(1);
write_rtl8225(dev, 0x9, 0x335); mdelay(1);
write_rtl8225(dev, 0xa, 0x9d4); mdelay(1);
write_rtl8225(dev, 0xb, 0x7bb); mdelay(1);
write_rtl8225(dev, 0xc, 0x850); mdelay(1);
write_rtl8225(dev, 0xd, 0xcdf); mdelay(1);
write_rtl8225(dev, 0xe, 0x2b); mdelay(1);
write_rtl8225(dev, 0xf, 0x114);
mdelay(100);
//if(priv->card_type != USB) /* maybe not needed even for 8185 */
// write_rtl8225(dev, 0x7, rtl8225_chan[channel]);
write_rtl8225(dev, 0x0, 0x1b7);
for(i=0;i<95;i++){
write_rtl8225(dev, 0x1, (u8)(i+1));
#if 0
if(priv->phy_ver == 1)
/* version A */
write_rtl8225(dev, 0x2, rtl8225a_rxgain[i]);
else
#endif
/* version B & C & D*/
write_rtl8225(dev, 0x2, rtl8225z2_rxgain[i]);
}
write_rtl8225(dev, 0x3, 0x80);
write_rtl8225(dev, 0x5, 0x4);
write_rtl8225(dev, 0x0, 0xb7);
write_rtl8225(dev, 0x2, 0xc4d);
if(priv->card_type == USB){
// force_pci_posting(dev);
mdelay(200);
write_rtl8225(dev, 0x2, 0x44d);
// force_pci_posting(dev);
mdelay(100);
}//End of if(priv->card_type == USB)
/* FIXME!! rtl8187 we have to check if calibrarion
* is successful and eventually cal. again (repeat
* the two write on reg 2)
*/
// Check for calibration status, 2005.11.17,
data = read_rtl8225(dev, 6);
if (!(data&0x00000080))
{
write_rtl8225(dev, 0x02, 0x0c4d);
force_pci_posting(dev); mdelay(200);
write_rtl8225(dev, 0x02, 0x044d);
force_pci_posting(dev); mdelay(100);
data = read_rtl8225(dev, 6);
if (!(data&0x00000080))
{
DMESGW("RF Calibration Failed!!!!\n");
}
}
//force_pci_posting(dev);
mdelay(200); //200 for 8187
// //if(priv->card_type != USB){
// write_rtl8225(dev, 0x2, 0x44d);
// write_rtl8225(dev, 0x7, rtl8225_chan[channel]);
// write_rtl8225(dev, 0x2, 0x47d);
//
// force_pci_posting(dev);
// mdelay(100);
//
// write_rtl8225(dev, 0x2, 0x44d);
// //}
write_rtl8225(dev, 0x0, 0x2bf);
if(priv->card_type != USB)
rtl8185_rf_pins_enable(dev);
//set up ZEBRA AGC table, 2005.11.17,
for(i=0;i<128;i++){
data = rtl8225_agc[i];
addr = i + 0x80; //enable writing AGC table
write_phy_ofdm(dev, 0xb, data);
mdelay(1);
write_phy_ofdm(dev, 0xa, addr);
mdelay(1);
}
#if 0
for(i=0;i<128;i++){
write_phy_ofdm(dev, 0xb, rtl8225_agc[i]);
mdelay(1);
write_phy_ofdm(dev, 0xa, (u8)i+ 0x80);
mdelay(1);
}
#endif
force_pci_posting(dev);
mdelay(1);
write_phy_ofdm(dev, 0x0, 0x1); mdelay(1);
write_phy_ofdm(dev, 0x1, 0x2); mdelay(1);
write_phy_ofdm(dev, 0x2, ((priv->card_type == USB)? 0x42 : 0x62)); mdelay(1);
write_phy_ofdm(dev, 0x3, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x4, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x5, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x6, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x7, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x8, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x9, 0xfe); mdelay(1);
write_phy_ofdm(dev, 0xa, 0x8); mdelay(1);
//write_phy_ofdm(dev, 0x18, 0xef);
// }
//}
write_phy_ofdm(dev, 0xb, 0x80); mdelay(1);
write_phy_ofdm(dev, 0xc, 0x1);mdelay(1);
//if(priv->card_type != USB)
write_phy_ofdm(dev, 0xd, 0x43);
write_phy_ofdm(dev, 0xe, 0xd3);mdelay(1);
#if 0
if(priv->card_8185 == 1){
if(priv->card_8185_Bversion)
write_phy_ofdm(dev, 0xf, 0x20);/*ver B*/
else
write_phy_ofdm(dev, 0xf, 0x28);/*ver C*/
}else{
#endif
write_phy_ofdm(dev, 0xf, 0x38);mdelay(1);
/*ver D & 8187*/
// }
// if(priv->card_8185 == 1 && priv->card_8185_Bversion)
// write_phy_ofdm(dev, 0x10, 0x04);/*ver B*/
// else
write_phy_ofdm(dev, 0x10, 0x84);mdelay(1);
/*ver C & D & 8187*/
write_phy_ofdm(dev, 0x11, 0x07);mdelay(1);
/*agc resp time 700*/
// if(priv->card_8185 == 2){
/* Ver D & 8187*/
write_phy_ofdm(dev, 0x12, 0x20);mdelay(1);
write_phy_ofdm(dev, 0x13, 0x20);mdelay(1);
#if 0
}else{
