static void check_hw_revision(void) { int modelrev = 0; int i; gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); /* * GPM1[1:0]: MODEL_REV[1:0] * Don't set as pull-none for these N/C pin. * TRM say that it may cause unexcepted state and leakage current. * and pull-none is only for output function. */ for (i = 0; i < 2; i++) s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT); /* GPM1[5:2]: HW_REV[3:0] */ for (i = 2; i < 6; i++) { s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT); s5p_gpio_set_pull(&gpio2->m1, i, GPIO_PULL_NONE); } /* GPM1[1:0]: MODEL_REV[1:0] */ for (i = 0; i < 2; i++) modelrev |= (s5p_gpio_get_value(&gpio2->m1, i) << i); /* board_rev[15:8] = model */ board_rev = modelrev << 8; }
static void board_uart_init(void) { struct exynos4_gpio_part1 *gpio1 = (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1(); struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); int i; /* * UART2 GPIOs * GPA1CON[0] = UART_2_RXD(2) * GPA1CON[1] = UART_2_TXD(2) * GPA1CON[2] = I2C_3_SDA (3) * GPA1CON[3] = I2C_3_SCL (3) */ for (i = 0; i < 4; i++) { s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC((i > 1) ? 0x3 : 0x2)); } /* UART_SEL GPY4[7] (part2) at EXYNOS4 */ s5p_gpio_set_pull(&gpio2->y4, 7, GPIO_PULL_UP); s5p_gpio_direction_output(&gpio2->y4, 7, 1); }
static void pmic_reset(void) { struct exynos4_gpio_part2 *gpio = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); s5p_gpio_direction_output(&gpio->x0, 7, 1); s5p_gpio_set_pull(&gpio->x2, 7, GPIO_PULL_NONE); }
void exynos_reset_lcd(void) { struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); s5p_gpio_direction_output(&gpio2->y4, 5, 1); udelay(10000); s5p_gpio_direction_output(&gpio2->y4, 5, 0); udelay(10000); s5p_gpio_direction_output(&gpio2->y4, 5, 1); }
static int exynos4_mmc_config(int peripheral, int flags) { struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *) samsung_get_base_gpio_part2(); struct s5p_gpio_bank *bank, *bank_ext; int i, start = 0, gpio_func = 0; switch (peripheral) { case PERIPH_ID_SDMMC0: bank = &gpio2->k0; bank_ext = &gpio2->k1; start = 3; gpio_func = GPIO_FUNC(0x2); break; case PERIPH_ID_SDMMC1: bank = &gpio2->k1; bank_ext = NULL; break; case PERIPH_ID_SDMMC2: bank = &gpio2->k2; bank_ext = &gpio2->k3; start = 3; gpio_func = GPIO_FUNC(0x3); break; case PERIPH_ID_SDMMC3: bank = &gpio2->k3; bank_ext = NULL; break; } if ((flags & PINMUX_FLAG_8BIT_MODE) && !bank_ext) { debug("SDMMC device %d does not support 8bit mode", peripheral); return -1; } if (flags & PINMUX_FLAG_8BIT_MODE) { for (i = start; i <= (start + 3); i++) { s5p_gpio_cfg_pin(bank_ext, i, gpio_func); s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_UP); s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X); } } for (i = 0; i < 2; i++) { s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); } for (i = 3; i <= 6; i++) { s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); s5p_gpio_set_pull(bank, i, GPIO_PULL_UP); s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); } return 0; }
void i2c_init_board(void) { struct exynos4_gpio_part1 *gpio1 = (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1(); struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); /* I2C_5 -> PMIC -> Adapter 0 */ s5p_gpio_direction_output(&gpio1->b, 7, 1); s5p_gpio_direction_output(&gpio1->b, 6, 1); /* I2C_9 -> FG -> Adapter 1 */ s5p_gpio_direction_output(&gpio2->y4, 0, 1); s5p_gpio_direction_output(&gpio2->y4, 1, 1); }
void i2c_init_board(void) { int err; struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); /* I2C_5 -> PMIC */ err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE); if (err) { debug("I2C%d not configured\n", (I2C_5)); return; } /* I2C_8 -> FG */ s5p_gpio_direction_output(&gpio2->y4, 0, 1); s5p_gpio_direction_output(&gpio2->y4, 1, 1); }
void exynos5_spi_config(int peripheral) { int cfg = 0, pin = 0, i; struct s5p_gpio_bank *bank = NULL; struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); struct exynos5_gpio_part2 *gpio2 = (struct exynos5_gpio_part2 *) samsung_get_base_gpio_part2(); switch (peripheral) { case PERIPH_ID_SPI0: bank = &gpio1->a2; cfg = GPIO_FUNC(0x2); pin = 0; break; case PERIPH_ID_SPI1: bank = &gpio1->a2; cfg = GPIO_FUNC(0x2); pin = 4; break; case PERIPH_ID_SPI2: bank = &gpio1->b1; cfg = GPIO_FUNC(0x5); pin = 1; break; case PERIPH_ID_SPI3: bank = &gpio2->f1; cfg = GPIO_FUNC(0x2); pin = 0; break; case PERIPH_ID_SPI4: for (i = 0; i < 2; i++) { s5p_gpio_cfg_pin(&gpio2->f0, i + 2, GPIO_FUNC(0x4)); s5p_gpio_cfg_pin(&gpio2->e0, i + 4, GPIO_FUNC(0x4)); } break; } if (peripheral != PERIPH_ID_SPI4) { for (i = pin; i < pin + 4; i++) s5p_gpio_cfg_pin(bank, i, cfg); } }
int board_mmc_init(bd_t *bis) { struct exynos4_gpio_part2 *gpio = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); int err; /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */ s5p_gpio_direction_output(&gpio->k0, 2, 1); s5p_gpio_set_pull(&gpio->k0, 2, GPIO_PULL_NONE); /* * MMC device init * mmc0 : eMMC (8-bit buswidth) * mmc2 : SD card (4-bit buswidth) */ err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); if (err) debug("SDMMC0 not configured\n"); else err = s5p_mmc_init(0, 8); /* T-flash detect */ s5p_gpio_cfg_pin(&gpio->x3, 4, 0xf); s5p_gpio_set_pull(&gpio->x3, 4, GPIO_PULL_UP); /* * Check the T-flash detect pin * GPX3[4] T-flash detect pin */ if (!s5p_gpio_get_value(&gpio->x3, 4)) { err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); if (err) debug("SDMMC2 not configured\n"); else err = s5p_mmc_init(2, 4); } return err; }
static void board_init_i2c(void) { int err; gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1(); gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); /* I2C_7 */ err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE); if (err) { debug("I2C%d not configured\n", (I2C_7)); return; } /* I2C_8 */ s5p_gpio_direction_output(&gpio1->f1, 4, 1); s5p_gpio_direction_output(&gpio1->f1, 5, 1); /* I2C_9 */ s5p_gpio_direction_output(&gpio2->m2, 1, 1); s5p_gpio_direction_output(&gpio2->m2, 0, 1); }
static void board_external_gpio_init(void) { gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); /* * some pins which in alive block are connected with external pull-up * but it's default setting is pull-down. * if that pin set as input then that floated */ s5p_gpio_set_pull(&gpio2->x0, 2, GPIO_PULL_NONE); /* PS_ALS_INT */ s5p_gpio_set_pull(&gpio2->x0, 4, GPIO_PULL_NONE); /* TSP_nINT */ s5p_gpio_set_pull(&gpio2->x0, 7, GPIO_PULL_NONE); /* AP_PMIC_IRQ*/ s5p_gpio_set_pull(&gpio2->x1, 5, GPIO_PULL_NONE); /* IF_PMIC_IRQ*/ s5p_gpio_set_pull(&gpio2->x2, 0, GPIO_PULL_NONE); /* VOL_UP */ s5p_gpio_set_pull(&gpio2->x2, 1, GPIO_PULL_NONE); /* VOL_DOWN */ s5p_gpio_set_pull(&gpio2->x2, 3, GPIO_PULL_NONE); /* FUEL_ALERT */ s5p_gpio_set_pull(&gpio2->x2, 4, GPIO_PULL_NONE); /* ADC_INT */ s5p_gpio_set_pull(&gpio2->x2, 7, GPIO_PULL_NONE); /* nPOWER */ s5p_gpio_set_pull(&gpio2->x3, 0, GPIO_PULL_NONE); /* WPC_INT */ s5p_gpio_set_pull(&gpio2->x3, 5, GPIO_PULL_NONE); /* OK_KEY */ s5p_gpio_set_pull(&gpio2->x3, 7, GPIO_PULL_NONE); /* HDMI_HPD */ }
static void exynos4_sromc_config(int flags) { struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *) samsung_get_base_gpio_part2(); int i; /* * SROM:CS1 and EBI * * GPY0[0] SROM_CSn[0] * GPY0[1] SROM_CSn[1](2) * GPY0[2] SROM_CSn[2] * GPY0[3] SROM_CSn[3] * GPY0[4] EBI_OEn(2) * GPY0[5] EBI_EEn(2) * * GPY1[0] EBI_BEn[0](2) * GPY1[1] EBI_BEn[1](2) * GPY1[2] SROM_WAIT(2) * GPY1[3] EBI_DATA_RDn(2) */ s5p_gpio_cfg_pin(&gpio2->y0, (flags & PINMUX_FLAG_BANK), GPIO_FUNC(2)); s5p_gpio_cfg_pin(&gpio2->y0, 4, GPIO_FUNC(2)); s5p_gpio_cfg_pin(&gpio2->y0, 5, GPIO_FUNC(2)); for (i = 0; i < 4; i++) s5p_gpio_cfg_pin(&gpio2->y1, i, GPIO_FUNC(2)); /* * EBI: 8 Addrss Lines * * GPY3[0] EBI_ADDR[0](2) * GPY3[1] EBI_ADDR[1](2) * GPY3[2] EBI_ADDR[2](2) * GPY3[3] EBI_ADDR[3](2) * GPY3[4] EBI_ADDR[4](2) * GPY3[5] EBI_ADDR[5](2) * GPY3[6] EBI_ADDR[6](2) * GPY3[7] EBI_ADDR[7](2) * * EBI: 16 Data Lines * * GPY5[0] EBI_DATA[0](2) * GPY5[1] EBI_DATA[1](2) * GPY5[2] EBI_DATA[2](2) * GPY5[3] EBI_DATA[3](2) * GPY5[4] EBI_DATA[4](2) * GPY5[5] EBI_DATA[5](2) * GPY5[6] EBI_DATA[6](2) * GPY5[7] EBI_DATA[7](2) * * GPY6[0] EBI_DATA[8](2) * GPY6[1] EBI_DATA[9](2) * GPY6[2] EBI_DATA[10](2) * GPY6[3] EBI_DATA[11](2) * GPY6[4] EBI_DATA[12](2) * GPY6[5] EBI_DATA[13](2) * GPY6[6] EBI_DATA[14](2) * GPY6[7] EBI_DATA[15](2) */ for (i = 0; i < 8; i++) { s5p_gpio_cfg_pin(&gpio2->y3, i, GPIO_FUNC(2)); s5p_gpio_set_pull(&gpio2->y3, i, GPIO_PULL_UP); s5p_gpio_cfg_pin(&gpio2->y5, i, GPIO_FUNC(2)); s5p_gpio_set_pull(&gpio2->y5, i, GPIO_PULL_UP); s5p_gpio_cfg_pin(&gpio2->y6, i, GPIO_FUNC(2)); s5p_gpio_set_pull(&gpio2->y6, i, GPIO_PULL_UP); } }