inline void dualx_tool_change(const uint8_t tmp_extruder, bool &no_move) { if (DEBUGGING(LEVELING)) { DEBUG_ECHOPGM("Dual X Carriage Mode "); switch (dual_x_carriage_mode) { case DXC_FULL_CONTROL_MODE: DEBUG_ECHOLNPGM("FULL_CONTROL"); break; case DXC_AUTO_PARK_MODE: DEBUG_ECHOLNPGM("AUTO_PARK"); break; case DXC_DUPLICATION_MODE: DEBUG_ECHOLNPGM("DUPLICATION"); break; case DXC_MIRRORED_MODE: DEBUG_ECHOLNPGM("MIRRORED"); break; } } const float xhome = x_home_pos(active_extruder); if (dual_x_carriage_mode == DXC_AUTO_PARK_MODE && IsRunning() && (delayed_move_time || current_position[X_AXIS] != xhome) && ! no_move ) { if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("MoveX to ", xhome); // Park old head planner.buffer_line(xhome, current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); planner.synchronize(); } // Apply Y & Z extruder offset (X offset is used as home pos with Dual X) current_position[Y_AXIS] -= hotend_offset[Y_AXIS][active_extruder] - hotend_offset[Y_AXIS][tmp_extruder]; current_position[Z_AXIS] -= hotend_offset[Z_AXIS][active_extruder] - hotend_offset[Z_AXIS][tmp_extruder]; // Activate the new extruder ahead of calling set_axis_is_at_home! active_extruder = tmp_extruder; // This function resets the max/min values - the current position may be overwritten below. set_axis_is_at_home(X_AXIS); if (DEBUGGING(LEVELING)) DEBUG_POS("New Extruder", current_position); switch (dual_x_carriage_mode) { case DXC_FULL_CONTROL_MODE: // New current position is the position of the activated extruder current_position[X_AXIS] = inactive_extruder_x_pos; // Save the inactive extruder's position (from the old current_position) inactive_extruder_x_pos = destination[X_AXIS]; break; case DXC_AUTO_PARK_MODE: // record current raised toolhead position for use by unpark COPY(raised_parked_position, current_position); active_extruder_parked = true; delayed_move_time = 0; break; default: break; } if (DEBUGGING(LEVELING)) { DEBUG_ECHOLNPAIR("Active extruder parked: ", active_extruder_parked ? "yes" : "no"); DEBUG_POS("New extruder (parked)", current_position); } }
/** * G28: Home all axes according to settings * * Parameters * * None Home to all axes with no parameters. * With QUICK_HOME enabled XY will home together, then Z. * * O Home only if position is unknown * * Rn Raise by n mm/inches before homing * * Cartesian/SCARA parameters * * X Home to the X endstop * Y Home to the Y endstop * Z Home to the Z endstop * */ void GcodeSuite::G28(const bool always_home_all) { #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) { SERIAL_ECHOLNPGM(">>> G28"); log_machine_info(); } #endif #if ENABLED(DUAL_X_CARRIAGE) bool IDEX_saved_duplication_state = extruder_duplication_enabled; DualXMode IDEX_saved_mode = dual_x_carriage_mode; #endif #if ENABLED(MARLIN_DEV_MODE) if (parser.seen('S')) { LOOP_XYZ(a) set_axis_is_at_home((AxisEnum)a); sync_plan_position(); SERIAL_ECHOLNPGM("Simulated Homing"); report_current_position(); #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("<<< G28"); #endif return; } #endif if (parser.boolval('O')) { if ( #if ENABLED(HOME_AFTER_DEACTIVATE) all_axes_known() // homing needed anytime steppers deactivate #else all_axes_homed() // homing needed only if never homed #endif ) { #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) { SERIAL_ECHOLNPGM("> homing not needed, skip"); SERIAL_ECHOLNPGM("<<< G28"); } #endif return; } } // Wait for planner moves to finish! planner.synchronize(); // Disable the leveling matrix before homing #if HAS_LEVELING // Cancel the active G29 session #if ENABLED(PROBE_MANUALLY) g29_in_progress = false; #endif #if ENABLED(RESTORE_LEVELING_AFTER_G28) const bool leveling_was_active = planner.leveling_active; #endif set_bed_leveling_enabled(false); #endif #if ENABLED(CNC_WORKSPACE_PLANES) workspace_plane = PLANE_XY; #endif #if ENABLED(BLTOUCH) bltouch_init(); #endif #if ENABLED(IMPROVE_HOMING_RELIABILITY) slow_homing_t slow_homing{0}; slow_homing.acceleration.x = planner.settings.max_acceleration_mm_per_s2[X_AXIS]; slow_homing.acceleration.y = planner.settings.max_acceleration_mm_per_s2[Y_AXIS]; slow_homing.jerk.x = planner.max_jerk[X_AXIS]; slow_homing.jerk.y = planner.max_jerk[Y_AXIS]; planner.settings.max_acceleration_mm_per_s2[X_AXIS] = 100; planner.settings.max_acceleration_mm_per_s2[Y_AXIS] = 100; planner.max_jerk[X_AXIS] = 0; planner.max_jerk[Y_AXIS] = 0; // steps per sq second need to be updated to agree with the units per sq second (as they are what is used in the planner) planner.reset_acceleration_rates(); #endif // Always home with tool 0 active #if HOTENDS > 1 #if DISABLED(DELTA) || ENABLED(DELTA_HOME_TO_SAFE_ZONE) const uint8_t old_tool_index = active_extruder; #endif tool_change(0, 0, true); #endif #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE) extruder_duplication_enabled = false; #endif setup_for_endstop_or_probe_move(); #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("> endstops.enable(true)"); #endif endstops.enable(true); // Enable endstops for next homing move #if ENABLED(DELTA) home_delta(); UNUSED(always_home_all); #else // NOT DELTA const bool homeX = always_home_all || parser.seen('X'), homeY = always_home_all || parser.seen('Y'), homeZ = always_home_all || parser.seen('Z'), home_all = (!homeX && !homeY && !homeZ) || (homeX && homeY && homeZ); set_destination_from_current(); #if Z_HOME_DIR > 0 // If homing away from BED do Z first if (home_all || homeZ) homeaxis(Z_AXIS); #endif const float z_homing_height = ( #if ENABLED(UNKNOWN_Z_NO_RAISE) !TEST(axis_known_position, Z_AXIS) ? 0 : #endif (parser.seenval('R') ? parser.value_linear_units() : Z_HOMING_HEIGHT) ); if (z_homing_height && (home_all || homeX || homeY)) { // Raise Z before homing any other axes and z is not already high enough (never lower z) destination[Z_AXIS] = z_homing_height; if (destination[Z_AXIS] > current_position[Z_AXIS]) { #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPAIR("Raise Z (before homing) to ", destination[Z_AXIS]); #endif do_blocking_move_to_z(destination[Z_AXIS]); } } #if ENABLED(QUICK_HOME) if (home_all || (homeX && homeY)) quick_home_xy(); #endif // Home Y (before X) #if ENABLED(HOME_Y_BEFORE_X) if (home_all || homeY #if ENABLED(CODEPENDENT_XY_HOMING) || homeX #endif ) homeaxis(Y_AXIS); #endif // Home X if (home_all || homeX #if ENABLED(CODEPENDENT_XY_HOMING) && DISABLED(HOME_Y_BEFORE_X) || homeY #endif ) { #if ENABLED(DUAL_X_CARRIAGE) // Always home the 2nd (right) extruder first active_extruder = 1; homeaxis(X_AXIS); // Remember this extruder's position for later tool change inactive_extruder_x_pos = current_position[X_AXIS]; // Home the 1st (left) extruder active_extruder = 0; homeaxis(X_AXIS); // Consider the active extruder to be parked COPY(raised_parked_position, current_position); delayed_move_time = 0; active_extruder_parked = true; #else homeaxis(X_AXIS); #endif } // Home Y (after X) #if DISABLED(HOME_Y_BEFORE_X) if (home_all || homeY) homeaxis(Y_AXIS); #endif // Home Z last if homing towards the bed #if Z_HOME_DIR < 0 if (home_all || homeZ) { #if ENABLED(Z_SAFE_HOMING) home_z_safely(); #else homeaxis(Z_AXIS); #endif #if HOMING_Z_WITH_PROBE && defined(Z_AFTER_PROBING) move_z_after_probing(); #endif } // home_all || homeZ #endif // Z_HOME_DIR < 0 sync_plan_position(); #endif // !DELTA (G28) /** * Preserve DXC mode across a G28 for IDEX printers in DXC_DUPLICATION_MODE. * This is important because it lets a user use the LCD Panel to set an IDEX Duplication mode, and * then print a standard GCode file that contains a single print that does a G28 and has no other * IDEX specific commands in it. */ #if ENABLED(DUAL_X_CARRIAGE) if (dxc_is_duplicating()) { // Always home the 2nd (right) extruder first active_extruder = 1; homeaxis(X_AXIS); // Remember this extruder's position for later tool change inactive_extruder_x_pos = current_position[X_AXIS]; // Home the 1st (left) extruder active_extruder = 0; homeaxis(X_AXIS); // Consider the active extruder to be parked COPY(raised_parked_position, current_position); delayed_move_time = 0; active_extruder_parked = true; extruder_duplication_enabled = IDEX_saved_duplication_state; extruder_duplication_enabled = false; dual_x_carriage_mode = IDEX_saved_mode; stepper.set_directions(); } #endif // DUAL_X_CARRIAGE endstops.not_homing(); #if ENABLED(DELTA) && ENABLED(DELTA_HOME_TO_SAFE_ZONE) // move to a height where we can use the full xy-area do_blocking_move_to_z(delta_clip_start_height); #endif #if HAS_LEVELING && ENABLED(RESTORE_LEVELING_AFTER_G28) set_bed_leveling_enabled(leveling_was_active); #endif clean_up_after_endstop_or_probe_move(); // Restore the active tool after homing #if HOTENDS > 1 && (DISABLED(DELTA) || ENABLED(DELTA_HOME_TO_SAFE_ZONE)) #if ENABLED(PARKING_EXTRUDER) #define NO_FETCH false // fetch the previous toolhead #else #define NO_FETCH true #endif tool_change(old_tool_index, 0, NO_FETCH); #endif #if ENABLED(IMPROVE_HOMING_RELIABILITY) planner.settings.max_acceleration_mm_per_s2[X_AXIS] = slow_homing.acceleration.x; planner.settings.max_acceleration_mm_per_s2[Y_AXIS] = slow_homing.acceleration.y; planner.max_jerk[X_AXIS] = slow_homing.jerk.x; planner.max_jerk[Y_AXIS] = slow_homing.jerk.y; // steps per sq second need to be updated to agree with the units per sq second (as they are what is used in the planner) planner.reset_acceleration_rates(); #endif ui.refresh(); report_current_position(); #if ENABLED(NANODLP_Z_SYNC) #if ENABLED(NANODLP_ALL_AXIS) #define _HOME_SYNC true // For any axis, output sync text. #else #define _HOME_SYNC (home_all || homeZ) // Only for Z-axis #endif if (_HOME_SYNC) SERIAL_ECHOLNPGM(MSG_Z_MOVE_COMP); #endif #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("<<< G28"); #endif #if HAS_DRIVER(L6470) // Set L6470 absolute position registers to counts for (uint8_t j = 1; j <= L6470::chain[0]; j++) { const uint8_t cv = L6470::chain[j]; L6470.set_param(cv, L6470_ABS_POS, stepper.position((AxisEnum)L6470.axis_xref[cv])); } #endif }