C++ (Cpp) set_hw_reason 예제들

예제 #1

파일: gpio_input.c 프로젝트: boa19861105/BOA_Butterfly2_M6.0_kernel

static void power_key_led_off_work_func(struct work_struct *dummy)
{
	if (power_key_led_requested) {
		if (cancel_delayed_work_sync(&power_key_led_on_work)) {
			KEY_LOGI("[PWR] cancel power key led work successfully(%x)\n", power_key_led_requested);
		} else
			KEY_LOGI("[PWR] cancel power key led work unsuccessfully (%x)\n", power_key_led_requested);

		power_key_led_requested = 0;
	}
	if (pre_power_key_led_status == 1) {
#ifdef CONFIG_POWER_KEY_CLR_RESET
		cancel_delayed_work_sync(&power_key_restart_work);
#endif
		KEY_LOGI("[PWR] change power key led off\n");
#ifdef CONFIG_QPNP_PWM
#ifdef CONFIG_VK_LED
		qpnp_led_set_for_key(0);
#endif
#else
		pm8xxx_led_current_set_for_key(0);
#endif
		pre_power_key_led_status = 0;
#ifdef CONFIG_POWER_KEY_CLR_RESET
		if(!is_rrm1_mode())
#endif
			set_hw_reason(0);
	}
}

예제 #2

static void power_key_led_on_work_func(struct work_struct *dummy)
{
	KEY_LOGI("[PWR] %s in (%x)\n", __func__, power_key_led_requested);
	if (power_key_led_requested == 1) {
		pre_power_key_led_status = 1;
		KEY_LOGI("[PWR] change power key led on\n");
		pm8xxx_led_current_set_for_key(1);
		set_hw_reason(HW_RESET_REASON);
	}
}

예제 #3

파일: gpio_input.c 프로젝트: boyan3010/Villec2_ShooterU_Kernel_3.0.X

static void power_key_led_on_work_func(struct work_struct *dummy)
{
	KEY_LOGI("[PWR] %s in (%x)\n", __func__, power_key_led_requested);
	if (power_key_led_requested == 1) {
		pre_power_key_led_status = 1;
		KEY_LOGI("[PWR] change power key led on\n");
		button_backlight_flash(1);
		set_hw_reason(HW_RESET_REASON);
	}
}

예제 #4

static void power_key_led_on_work_func(struct work_struct *dummy)
{
	KEY_LOGI("[PWR] %s in (%x)\n", __func__, power_key_led_requested);
	if (power_key_led_requested == 1) {
		pre_power_key_led_status = 1;
		KEY_LOGI("[PWR] change power key led on\n");
		pm8xxx_led_current_set_for_key(1);
		set_hw_reason(HW_RESET_REASON);
		KEY_LOGI("[PWR] Show Blocked State -- long press power key\n");
		show_state_filter(TASK_UNINTERRUPTIBLE);
	}
}

예제 #5

static void power_key_led_off_work_func(struct work_struct *dummy)
{
	if (power_key_led_requested) {
		if (cancel_delayed_work_sync(&power_key_led_on_work)) {
			KEY_LOGI("[PWR] cancel power key led work successfully(%x)\n", power_key_led_requested);
		} else
			KEY_LOGI("[PWR] cancel power key led work unsuccessfully (%x)\n", power_key_led_requested);

		power_key_led_requested = 0;
	}
	if (pre_power_key_led_status == 1) {
		KEY_LOGI("[PWR] change power key led off\n");
		pm8xxx_led_current_set_for_key(0);
		pre_power_key_led_status = 0;
		set_hw_reason(0);
	}
}

예제 #6

파일: gpio_input.c 프로젝트: boa19861105/BOA_Butterfly2_M6.0_kernel

static void power_key_restart_work_func(struct work_struct *dummy)
{
#ifndef CONFIG_POWER_VOLUP_RESET
	int pocket_mode = (board_mfg_mode() == MFG_MODE_NORMAL) ? power_key_check_in_pocket() : 0;
	KEY_LOGI( "%s: power_key_check_in_pocket = %d\n", __func__, pocket_mode);

	if (!pocket_mode && pre_power_key_led_status == 1 && !is_rrm1_mode()) {
#else
	uint8_t gpio_val = 0, i, idx_pwr = 9, idx_vup = 9;
	struct gpio_event_input_info *local = gis;
	for (i = 0; i < local->keymap_size; i++) {
		if (local->keymap[i].code == KEY_POWER) {
			idx_pwr = i;
			continue;
		}
		if (local->keymap[i].code == KEY_VOLUMEUP)
			idx_vup = i;
	}
	gpio_val = !(gpio_get_value(local->keymap[idx_pwr].gpio) |
		     gpio_get_value(local->keymap[idx_vup].gpio));

	if (gpio_val && pre_power_key_led_status == 1 && !is_rrm1_mode()) {
		KEY_LOGI("%s, (PWR+VOL_UP) reset", __func__);
#endif
		
		set_hw_reason(0);
#if defined(CONFIG_PM8921_BMS) && (CONFIG_HTC_BATT_8960)
		pm8921_store_hw_reset_reason(1);
#endif
		clear_hw_reset();
		set_restart_to_ramdump("Powerkey Hard Reset - SW");
		msm_restart(0, NULL);
	}
}

static DECLARE_DELAYED_WORK(power_key_restart_work, power_key_restart_work_func);
#endif

static void power_key_led_on_work_func(struct work_struct *dummy)
{
	KEY_LOGI("[PWR] %s in (%x)\n", __func__, power_key_led_requested);
	if (power_key_led_requested == 1) {
		pre_power_key_led_status = 1;
#ifdef CONFIG_POWER_KEY_CLR_RESET
		schedule_delayed_work(&power_key_restart_work, PWRKEYKP_DELAY);
#endif
		KEY_LOGI("[PWR] change power key led on\n");
#ifdef CONFIG_QPNP_PWM
#ifdef CONFIG_VK_LED
		qpnp_led_set_for_key(1);
#endif
#else
		pm8xxx_led_current_set_for_key(1);
#endif
#ifdef CONFIG_POWER_KEY_CLR_RESET
		if(!is_rrm1_mode())
#endif
			set_hw_reason(HW_RESET_REASON);
		KEY_LOGI("[PWR] Show Blocked State -- long press power key\n");
		show_state_filter(TASK_UNINTERRUPTIBLE);
	}
}