/** * ubi_io_write - write data to a physical eraseblock. * @ubi: UBI device description object * @buf: buffer with the data to write * @pnum: physical eraseblock number to write to * @offset: offset within the physical eraseblock where to write * @len: how many bytes to write * * This function writes @len bytes of data from buffer @buf to offset @offset * of physical eraseblock @pnum. If all the data were successfully written, * zero is returned. If an error occurred, this function returns a negative * error code. If %-EIO is returned, the physical eraseblock most probably went * bad. * * Note, in case of an error, it is possible that something was still written * to the flash media, but may be some garbage. */ int ubi_io_write(struct ubi_device *ubi, const void *buf, int pnum, int offset, int len) { int err; size_t written; loff_t addr; dbg_io("write %d bytes to PEB %d:%d", len, pnum, offset); ubi_assert(pnum >= 0 && pnum < ubi->peb_count); ubi_assert(offset >= 0 && offset + len <= ubi->peb_size); ubi_assert(offset % ubi->hdrs_min_io_size == 0); ubi_assert(len > 0 && len % ubi->hdrs_min_io_size == 0); if (ubi->ro_mode) { ubi_err(ubi, "read-only mode"); return -EROFS; } err = self_check_not_bad(ubi, pnum); if (err) return err; /* The area we are writing to has to contain all 0xFF bytes */ err = ubi_self_check_all_ff(ubi, pnum, offset, len); if (err) return err; if (offset >= ubi->leb_start) { /* * We write to the data area of the physical eraseblock. Make * sure it has valid EC and VID headers. */ err = self_check_peb_ec_hdr(ubi, pnum); if (err) return err; err = self_check_peb_vid_hdr(ubi, pnum); if (err) return err; } if (ubi_dbg_is_write_failure(ubi)) { ubi_err(ubi, "cannot write %d bytes to PEB %d:%d (emulated)", len, pnum, offset); dump_stack(); return -EIO; } addr = (loff_t)pnum * ubi->peb_size + offset; err = mtd_write(ubi->mtd, addr, len, &written, buf); if (err) { ubi_err(ubi, "error %d while writing %d bytes to PEB %d:%d, written %zd bytes", err, len, pnum, offset, written); dump_stack(); ubi_dump_flash(ubi, pnum, offset, len); } else ubi_assert(written == len); if (!err) { err = self_check_write(ubi, buf, pnum, offset, len); if (err) return err; /* * Since we always write sequentially, the rest of the PEB has * to contain only 0xFF bytes. */ offset += len; len = ubi->peb_size - offset; if (len) err = ubi_self_check_all_ff(ubi, pnum, offset, len); } return err; }
/** * ubi_io_write - write data to a physical eraseblock. * @ubi: UBI device description object * @buf: buffer with the data to write * @pnum: physical eraseblock number to write to * @offset: offset within the physical eraseblock where to write * @len: how many bytes to write * * This function writes @len bytes of data from buffer @buf to offset @offset * of physical eraseblock @pnum. If all the data were successfully written, * zero is returned. If an error occurred, this function returns a negative * error code. If %-EIO is returned, the physical eraseblock most probably went * bad. * * Note, in case of an error, it is possible that something was still written * to the flash media, but may be some garbage. */ int ubi_io_write(struct ubi_device *ubi, const void *buf, int pnum, int offset, int len) { int err; size_t written; loff_t addr; dbg_io("write %d bytes to PEB %d:%d", len, pnum, offset); ubi_assert(pnum >= 0 && pnum < ubi->peb_count); ubi_assert(offset >= 0 && offset + len <= ubi->peb_size); ubi_assert(offset % ubi->hdrs_min_io_size == 0); ubi_assert(len > 0 && len % ubi->hdrs_min_io_size == 0); if (ubi->ro_mode) { ubi_err("read-only mode"); return -EROFS; } /* The below has to be compiled out if paranoid checks are disabled */ err = paranoid_check_not_bad(ubi, pnum); if (err) return err > 0 ? -EINVAL : err; /* The area we are writing to has to contain all 0xFF bytes */ err = paranoid_check_all_ff(ubi, pnum, offset, len); if (err) return err > 0 ? -EINVAL : err; if (offset >= ubi->leb_start) { /* * We write to the data area of the physical eraseblock. Make * sure it has valid EC and VID headers. */ err = paranoid_check_peb_ec_hdr(ubi, pnum); if (err) return err > 0 ? -EINVAL : err; err = paranoid_check_peb_vid_hdr(ubi, pnum); if (err) return err > 0 ? -EINVAL : err; } if (ubi_dbg_is_write_failure()) { dbg_err("cannot write %d bytes to PEB %d:%d " "(emulated)", len, pnum, offset); ubi_dbg_dump_stack(); return -EIO; } addr = (loff_t)pnum * ubi->peb_size + offset; err = ubi->mtd->write(ubi->mtd, addr, len, &written, buf); if (err) { ubi_err("error %d while writing %d bytes to PEB %d:%d, written" " %zd bytes", err, len, pnum, offset, written); ubi_dbg_dump_stack(); } else ubi_assert(written == len); return err; }