ACPI_STATUS
AcpiInitializeObjects (
UINT32 Flags)
{
ACPI_STATUS Status = AE_OK;
ACPI_FUNCTION_TRACE (AcpiInitializeObjects);
/*
* Run all _REG methods
*
* Note: Any objects accessed by the _REG methods will be automatically
* initialized, even if they contain executable AML (see the call to
* AcpiNsInitializeObjects below).
*/
if (!(Flags & ACPI_NO_ADDRESS_SPACE_INIT))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC,
"[Init] Executing _REG OpRegion methods\n"));
Status = AcpiEvInitializeOpRegions ();
if (ACPI_FAILURE (Status))
{
return_ACPI_STATUS (Status);
}
}
/*
* Execute any module-level code that was detected during the table load
* phase. Although illegal since ACPI 2.0, there are many machines that
* contain this type of code. Each block of detected executable AML code
* outside of any control method is wrapped with a temporary control
* method object and placed on a global list. The methods on this list
* are executed below.
*/
AcpiNsExecModuleCodeList ();
/*
* Initialize the objects that remain uninitialized. This runs the
* executable AML that may be part of the declaration of these objects:
* OperationRegions, BufferFields, Buffers, and Packages.
*/
if (!(Flags & ACPI_NO_OBJECT_INIT))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC,
"[Init] Completing Initialization of ACPI Objects\n"));
Status = AcpiNsInitializeObjects ();
if (ACPI_FAILURE (Status))
{
return_ACPI_STATUS (Status);
}
}
/*
* Initialize all device objects in the namespace. This runs the device
* _STA and _INI methods.
*/
if (!(Flags & ACPI_NO_DEVICE_INIT))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC,
"[Init] Initializing ACPI Devices\n"));
Status = AcpiNsInitializeDevices ();
if (ACPI_FAILURE (Status))
{
return_ACPI_STATUS (Status);
}
}
/*
* Initialize the GPE blocks defined in the FADT (GPE block 0 and 1).
* The runtime GPEs are enabled here.
*
* This is where the _PRW methods are executed for the GPEs. These
* methods can only be executed after the SCI and Global Lock handlers are
* installed and initialized.
*
* GPEs can only be enabled after the _REG, _STA, and _INI methods have
* been run. This ensures that all Operation Regions and all Devices have
* been initialized and are ready.
*/
if (!(Flags & ACPI_NO_EVENT_INIT))
{
Status = AcpiEvInstallFadtGpes ();
if (ACPI_FAILURE (Status))
{
return (Status);
}
}
/*
* Empty the caches (delete the cached objects) on the assumption that
* the table load filled them up more than they will be at runtime --
* thus wasting non-paged memory.
*/
Status = AcpiPurgeCachedObjects ();
AcpiGbl_StartupFlags |= ACPI_INITIALIZED_OK;
return_ACPI_STATUS (Status);
}
ACPI_STATUS
AcpiEnableSubsystem (
UINT32 Flags)
{
ACPI_STATUS Status = AE_OK;
ACPI_FUNCTION_TRACE (AcpiEnableSubsystem);
/* Enable ACPI mode */
if (!(Flags & ACPI_NO_ACPI_ENABLE))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC, "[Init] Going into ACPI mode\n"));
AcpiGbl_OriginalMode = AcpiHwGetMode();
Status = AcpiEnable ();
if (ACPI_FAILURE (Status))
{
ACPI_WARNING ((AE_INFO, "AcpiEnable failed"));
return_ACPI_STATUS (Status);
}
}
/*
* Install the default OpRegion handlers. These are installed unless
* other handlers have already been installed via the
* InstallAddressSpaceHandler interface.
*/
if (!(Flags & ACPI_NO_ADDRESS_SPACE_INIT))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC,
"[Init] Installing default address space handlers\n"));
Status = AcpiEvInstallRegionHandlers ();
if (ACPI_FAILURE (Status))
{
return_ACPI_STATUS (Status);
}
}
/*
* Initialize ACPI Event handling (Fixed and General Purpose)
*
* Note1: We must have the hardware and events initialized before we can
* execute any control methods safely. Any control method can require
* ACPI hardware support, so the hardware must be fully initialized before
* any method execution!
*
* Note2: Fixed events are initialized and enabled here. GPEs are
* initialized, but cannot be enabled until after the hardware is
* completely initialized (SCI and GlobalLock activated)
*/
if (!(Flags & ACPI_NO_EVENT_INIT))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC,
"[Init] Initializing ACPI events\n"));
Status = AcpiEvInitializeEvents ();
if (ACPI_FAILURE (Status))
{
return_ACPI_STATUS (Status);
}
}
/*
* Install the SCI handler and Global Lock handler. This completes the
* hardware initialization.
*/
if (!(Flags & ACPI_NO_HANDLER_INIT))
{
ACPI_DEBUG_PRINT ((ACPI_DB_EXEC,
"[Init] Installing SCI/GL handlers\n"));
Status = AcpiEvInstallXruptHandlers ();
if (ACPI_FAILURE (Status))
{
return_ACPI_STATUS (Status);
}
}
/*
* Complete the GPE initialization for the GPE blocks defined in the FADT
* (GPE block 0 and 1).
*
* Note1: This is where the _PRW methods are executed for the GPEs. These
* methods can only be executed after the SCI and Global Lock handlers are
* installed and initialized.
*
* Note2: Currently, there seems to be no need to run the _REG methods
* before execution of the _PRW methods and enabling of the GPEs.
*/
if (!(Flags & ACPI_NO_EVENT_INIT))
{
Status = AcpiEvInstallFadtGpes ();
if (ACPI_FAILURE (Status))
{
return (Status);
}
}
return_ACPI_STATUS (Status);
}