/**
* ar9003_hw_set_channel - set channel on single-chip device
* @ah: atheros hardware structure
* @chan:
*
* This is the function to change channel on single-chip devices, that is
* all devices after ar9280.
*
* This function takes the channel value in MHz and sets
* hardware channel value. Assumes writes have been enabled to analog bus.
*
* Actual Expression,
*
* For 2GHz channel,
* Channel Frequency = (3/4) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*
* For 5GHz channel,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^10)
* (freq_ref = 40MHz/(24>>amodeRefSel))
*
* For 5GHz channels which are 5MHz spaced,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*/
static int ar9003_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan)
{
u16 bMode, fracMode = 0, aModeRefSel = 0;
u32 freq, channelSel = 0, reg32 = 0;
struct chan_centers centers;
int loadSynthChannel;
ath9k_hw_get_channel_centers(ah, chan, ¢ers);
freq = centers.synth_center;
if (freq < 4800) { /* 2 GHz, fractional mode */
channelSel = CHANSEL_2G(freq);
/* Set to 2G mode */
bMode = 1;
} else {
channelSel = CHANSEL_5G(freq);
/* Doubler is ON, so, divide channelSel by 2. */
channelSel >>= 1;
/* Set to 5G mode */
bMode = 0;
}
/* Enable fractional mode for all channels */
fracMode = 1;
aModeRefSel = 0;
loadSynthChannel = 0;
reg32 = (bMode << 29);
REG_WRITE(ah, AR_PHY_SYNTH_CONTROL, reg32);
/* Enable Long shift Select for Synthesizer */
REG_RMW_FIELD(ah, AR_PHY_65NM_CH0_SYNTH4,
AR_PHY_SYNTH4_LONG_SHIFT_SELECT, 1);
/* Program Synth. setting */
reg32 = (channelSel << 2) | (fracMode << 30) |
(aModeRefSel << 28) | (loadSynthChannel << 31);
REG_WRITE(ah, AR_PHY_65NM_CH0_SYNTH7, reg32);
/* Toggle Load Synth channel bit */
loadSynthChannel = 1;
reg32 = (channelSel << 2) | (fracMode << 30) |
(aModeRefSel << 28) | (loadSynthChannel << 31);
REG_WRITE(ah, AR_PHY_65NM_CH0_SYNTH7, reg32);
ah->curchan = chan;
ah->curchan_rad_index = -1;
return 0;
}
/**
* ar9002_hw_set_channel - set channel on single-chip device
* @ah: atheros hardware structure
* @chan:
*
* This is the function to change channel on single-chip devices, that is
* all devices after ar9280.
*
* This function takes the channel value in MHz and sets
* hardware channel value. Assumes writes have been enabled to analog bus.
*
* Actual Expression,
*
* For 2GHz channel,
* Channel Frequency = (3/4) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*
* For 5GHz channel,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^10)
* (freq_ref = 40MHz/(24>>amodeRefSel))
*/
static int ar9002_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan)
{
u16 bMode, fracMode, aModeRefSel = 0;
u32 freq, ndiv, channelSel = 0, channelFrac = 0, reg32 = 0;
struct chan_centers centers;
u32 refDivA = 24;
ath9k_hw_get_channel_centers(ah, chan, ¢ers);
freq = centers.synth_center;
reg32 = REG_READ(ah, AR_PHY_SYNTH_CONTROL);
reg32 &= 0xc0000000;
if (freq < 4800) { /* 2 GHz, fractional mode */
u32 txctl;
int regWrites = 0;
bMode = 1;
fracMode = 1;
aModeRefSel = 0;
channelSel = CHANSEL_2G(freq);
if (AR_SREV_9287_11_OR_LATER(ah)) {
if (freq == 2484) {
/* Enable channel spreading for channel 14 */
REG_WRITE_ARRAY(&ah->iniCckfirJapan2484,
1, regWrites);
} else {
REG_WRITE_ARRAY(&ah->iniCckfirNormal,
1, regWrites);
}
} else {
txctl = REG_READ(ah, AR_PHY_CCK_TX_CTRL);
if (freq == 2484) {
/* Enable channel spreading for channel 14 */
REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
txctl | AR_PHY_CCK_TX_CTRL_JAPAN);
} else {
REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
txctl & ~AR_PHY_CCK_TX_CTRL_JAPAN);
}
}
} else {
bMode = 0;
fracMode = 0;
switch (ah->eep_ops->get_eeprom(ah, EEP_FRAC_N_5G)) {
case 0:
if (IS_CHAN_HALF_RATE(chan) || IS_CHAN_QUARTER_RATE(chan))
aModeRefSel = 0;
else if ((freq % 20) == 0)
aModeRefSel = 3;
else if ((freq % 10) == 0)
aModeRefSel = 2;
if (aModeRefSel)
break;
case 1:
default:
aModeRefSel = 0;
/*
* Enable 2G (fractional) mode for channels
* which are 5MHz spaced.
*/
fracMode = 1;
refDivA = 1;
channelSel = CHANSEL_5G(freq);
/* RefDivA setting */
ath9k_hw_analog_shift_rmw(ah, AR_AN_SYNTH9,
AR_AN_SYNTH9_REFDIVA,
AR_AN_SYNTH9_REFDIVA_S, refDivA);
}
if (!fracMode) {
ndiv = (freq * (refDivA >> aModeRefSel)) / 60;
channelSel = ndiv & 0x1ff;
channelFrac = (ndiv & 0xfffffe00) * 2;
channelSel = (channelSel << 17) | channelFrac;
}
}
/*
* Take the MHz channel value and set the Channel value
*
* ASSUMES: Writes enabled to analog bus
*
* Actual Expression,
*
* For 2GHz channel,
* Channel Frequency = (3/4) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*
* For 5GHz channel,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^10)
* (freq_ref = 40MHz/(24>>amode_ref_sel))
*
* For 5GHz channels which are 5MHz spaced,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*/
static HAL_BOOL
ar9300_set_channel(struct ath_hal *ah, struct ieee80211_channel *chan)
{
u_int16_t b_mode, frac_mode = 0, a_mode_ref_sel = 0;
u_int32_t freq, channel_sel, reg32;
u_int8_t clk_25mhz = AH9300(ah)->clk_25mhz;
CHAN_CENTERS centers;
int load_synth_channel;
#ifdef AH_DEBUG_ALQ
HAL_CHANNEL_INTERNAL *ichan = ath_hal_checkchannel(ah, chan);
#endif
/*
* Put this behind AH_DEBUG_ALQ for now until the Hornet
* channel_sel code below is made to work.
*/
#ifdef AH_DEBUG_ALQ
OS_MARK(ah, AH_MARK_SETCHANNEL, ichan->channel);
#endif
ar9300_get_channel_centers(ah, chan, ¢ers);
freq = centers.synth_center;
if (freq < 4800) { /* 2 GHz, fractional mode */
b_mode = 1; /* 2 GHz */
if (AR_SREV_HORNET(ah)) {
#if 0
u_int32_t ichan =
ieee80211_mhz2ieee(ah, chan->ic_freq, chan->ic_flags);
HALASSERT(ichan > 0 && ichan <= 14);
if (clk_25mhz) {
channel_sel = ar9300_chansel_xtal_25M[ichan - 1];
} else {
channel_sel = ar9300_chansel_xtal_40M[ichan - 1];
}
#endif
uint32_t i;
/*
* Pay close attention to this bit!
*
* We need to map the actual desired synth frequency to
* one of the channel select array entries.
*
* For HT20, it'll align with the channel we select.
*
* For HT40 though it won't - the centre frequency
* will not be the frequency of chan->ic_freq or ichan->freq;
* it needs to be whatever frequency maps to 'freq'.
*/
i = ath_hal_mhz2ieee_2ghz(ah, freq);
HALASSERT(i > 0 && i <= 14);
if (clk_25mhz) {
channel_sel = ar9300_chansel_xtal_25M[i - 1];
} else {
channel_sel = ar9300_chansel_xtal_40M[i - 1];
}
} else if (AR_SREV_POSEIDON(ah) || AR_SREV_APHRODITE(ah)) {
u_int32_t channel_frac;
/*
* freq_ref = (40 / (refdiva >> a_mode_ref_sel));
* (where refdiva = 1 and amoderefsel = 0)
* ndiv = ((chan_mhz * 4) / 3) / freq_ref;
* chansel = int(ndiv), chanfrac = (ndiv - chansel) * 0x20000
*/
channel_sel = (freq * 4) / 120;
channel_frac = (((freq * 4) % 120) * 0x20000) / 120;
channel_sel = (channel_sel << 17) | (channel_frac);
} else if (AR_SREV_WASP(ah) || AR_SREV_SCORPION(ah) || AR_SREV_HONEYBEE(ah)) {
u_int32_t channel_frac;
if (clk_25mhz) {
/*
* freq_ref = (50 / (refdiva >> a_mode_ref_sel));
* (where refdiva = 1 and amoderefsel = 0)
* ndiv = ((chan_mhz * 4) / 3) / freq_ref;
* chansel = int(ndiv), chanfrac = (ndiv - chansel) * 0x20000
*/
if (AR_SREV_SCORPION(ah) || AR_SREV_HONEYBEE(ah)) {
/* Doubler is off for Scorpion */
channel_sel = (freq * 4) / 75;
channel_frac = (((freq * 4) % 75) * 0x20000) / 75;
} else {
channel_sel = (freq * 2) / 75;
channel_frac = (((freq * 2) % 75) * 0x20000) / 75;
}
} else {
/*
* freq_ref = (50 / (refdiva >> a_mode_ref_sel));
* (where refdiva = 1 and amoderefsel = 0)
* ndiv = ((chan_mhz * 4) / 3) / freq_ref;
* chansel = int(ndiv), chanfrac = (ndiv - chansel) * 0x20000
*/
if (AR_SREV_SCORPION(ah)) {
/* Doubler is off for Scorpion */
channel_sel = (freq * 4) / 120;
channel_frac = (((freq * 4) % 120) * 0x20000) / 120;
} else {
channel_sel = (freq * 2) / 120;
channel_frac = (((freq * 2) % 120) * 0x20000) / 120;
}
}
channel_sel = (channel_sel << 17) | (channel_frac);
} else {
channel_sel = CHANSEL_2G(freq);
}
} else {
b_mode = 0; /* 5 GHz */
if ((AR_SREV_WASP(ah) || AR_SREV_SCORPION(ah)) && clk_25mhz){
u_int32_t channel_frac;
/*
* freq_ref = (50 / (refdiva >> amoderefsel));
* (refdiva = 1, amoderefsel = 0)
* ndiv = ((chan_mhz * 2) / 3) / freq_ref;
* chansel = int(ndiv), chanfrac = (ndiv - chansel) * 0x20000
*/
channel_sel = freq / 75 ;
channel_frac = ((freq % 75) * 0x20000) / 75;
channel_sel = (channel_sel << 17) | (channel_frac);
} else {
channel_sel = CHANSEL_5G(freq);
/* Doubler is ON, so, divide channel_sel by 2. */
channel_sel >>= 1;
}
}
/* Enable fractional mode for all channels */
frac_mode = 1;
a_mode_ref_sel = 0;
load_synth_channel = 0;
reg32 = (b_mode << 29);
OS_REG_WRITE(ah, AR_PHY_SYNTH_CONTROL, reg32);
/* Enable Long shift Select for Synthesizer */
OS_REG_RMW_FIELD(ah,
AR_PHY_65NM_CH0_SYNTH4, AR_PHY_SYNTH4_LONG_SHIFT_SELECT, 1);
/* program synth. setting */
reg32 =
(channel_sel << 2) |
(a_mode_ref_sel << 28) |
(frac_mode << 30) |
(load_synth_channel << 31);
if (IEEE80211_IS_CHAN_QUARTER(chan)) {
reg32 += CHANSEL_5G_DOT5MHZ;
}
OS_REG_WRITE(ah, AR_PHY_65NM_CH0_SYNTH7, reg32);
/* Toggle Load Synth channel bit */
load_synth_channel = 1;
reg32 |= load_synth_channel << 31;
OS_REG_WRITE(ah, AR_PHY_65NM_CH0_SYNTH7, reg32);
AH_PRIVATE(ah)->ah_curchan = chan;
return AH_TRUE;
}
