static void mtk_pconf_set_ies_smt(struct mtk_pinctrl *pctl, unsigned pin,
int value, enum pin_config_param param)
{
unsigned int reg_addr, offset;
unsigned int bit;
int ret;
/*
* Due to some pins are irregular, their input enable and smt
* control register are discontinuous, but they are mapping together.
* So we need this special handle.
*/
if (pctl->devdata->spec_ies_smt_set) {
ret = pctl->devdata->spec_ies_smt_set(mtk_get_regmap(pctl, pin),
pin, pctl->devdata->port_align, value);
if (!ret)
return;
}
bit = BIT(pin & 0xf);
if (param == PIN_CONFIG_INPUT_ENABLE)
offset = pctl->devdata->ies_offset;
else
offset = pctl->devdata->smt_offset;
if (value)
reg_addr = SET_ADDR(mtk_get_port(pctl, pin) + offset, pctl);
else
reg_addr = CLR_ADDR(mtk_get_port(pctl, pin) + offset, pctl);
regmap_write(mtk_get_regmap(pctl, pin), reg_addr, bit);
}
static int mtk_pconf_set_pull_select(struct mtk_pinctrl *pctl,
unsigned int pin, bool enable, bool isup, unsigned int arg)
{
unsigned int bit;
unsigned int reg_pullen, reg_pullsel;
int ret;
/* Some pins' pull setting are very different,
* they have separate pull up/down bit, R0 and R1
* resistor bit, so we need this special handle.
*/
if (pctl->devdata->spec_pull_set) {
ret = pctl->devdata->spec_pull_set(mtk_get_regmap(pctl, pin),
pin, pctl->devdata->port_align, isup, arg);
if (!ret)
return 0;
}
/* For generic pull config, default arg value should be 0 or 1. */
if (arg != 0 && arg != 1) {
dev_err(pctl->dev, "invalid pull-up argument %d on pin %d .\n",
arg, pin);
return -EINVAL;
}
bit = BIT(pin & 0xf);
if (enable)
reg_pullen = SET_ADDR(mtk_get_port(pctl, pin) +
pctl->devdata->pullen_offset, pctl);
else
reg_pullen = CLR_ADDR(mtk_get_port(pctl, pin) +
pctl->devdata->pullen_offset, pctl);
if (isup)
reg_pullsel = SET_ADDR(mtk_get_port(pctl, pin) +
pctl->devdata->pullsel_offset, pctl);
else
reg_pullsel = CLR_ADDR(mtk_get_port(pctl, pin) +
pctl->devdata->pullsel_offset, pctl);
regmap_write(mtk_get_regmap(pctl, pin), reg_pullen, bit);
regmap_write(mtk_get_regmap(pctl, pin), reg_pullsel, bit);
return 0;
}
static void mtk_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
unsigned int reg_addr;
unsigned int bit;
struct mtk_pinctrl *pctl = dev_get_drvdata(chip->dev);
reg_addr = mtk_get_port(pctl, offset) + pctl->devdata->dout_offset;
bit = BIT(offset & 0xf);
if (value)
reg_addr = SET_ADDR(reg_addr, pctl);
else
reg_addr = CLR_ADDR(reg_addr, pctl);
regmap_write(mtk_get_regmap(pctl, offset), reg_addr, bit);
}
static int mtk_pconf_set_ies_smt(struct mtk_pinctrl *pctl, unsigned pin,
int value, enum pin_config_param arg)
{
unsigned int reg_addr, offset;
unsigned int bit;
/**
* Due to some soc are not support ies/smt config, add this special
* control to handle it.
*/
if (!pctl->devdata->spec_ies_smt_set &&
pctl->devdata->ies_offset == MTK_PINCTRL_NOT_SUPPORT &&
arg == PIN_CONFIG_INPUT_ENABLE)
return -EINVAL;
if (!pctl->devdata->spec_ies_smt_set &&
pctl->devdata->smt_offset == MTK_PINCTRL_NOT_SUPPORT &&
arg == PIN_CONFIG_INPUT_SCHMITT_ENABLE)
return -EINVAL;
/*
* Due to some pins are irregular, their input enable and smt
* control register are discontinuous, so we need this special handle.
*/
if (pctl->devdata->spec_ies_smt_set) {
return pctl->devdata->spec_ies_smt_set(mtk_get_regmap(pctl, pin),
pin, pctl->devdata->port_align, value, arg);
}
bit = BIT(pin & 0xf);
if (arg == PIN_CONFIG_INPUT_ENABLE)
offset = pctl->devdata->ies_offset;
else
offset = pctl->devdata->smt_offset;
if (value)
reg_addr = SET_ADDR(mtk_get_port(pctl, pin) + offset, pctl);
else
reg_addr = CLR_ADDR(mtk_get_port(pctl, pin) + offset, pctl);
regmap_write(mtk_get_regmap(pctl, pin), reg_addr, bit);
return 0;
}
static int mtk_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
struct pinctrl_gpio_range *range, unsigned offset,
bool input)
{
unsigned int reg_addr;
unsigned int bit;
struct mtk_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
reg_addr = mtk_get_port(pctl, offset) + pctl->devdata->dir_offset;
bit = BIT(offset & 0xf);
if (input)
/* Different SoC has different alignment offset. */
reg_addr = CLR_ADDR(reg_addr, pctl);
else
reg_addr = SET_ADDR(reg_addr, pctl);
regmap_write(mtk_get_regmap(pctl, offset), reg_addr, bit);
return 0;
}
