/* Interrupt routine for example_uart */
static void App_Interrupt_Test(void)
{
uint8_t isExit = 0, userInput;
int len;
App_Interrupt_Init();
/* Print out uart interrupt menu */
Print_Menu_Interrupt(LPC_UART);
while (!isExit) {
len = 0;
while (len == 0) {
len = Chip_UART_ReadRB(LPC_UART, &rxring, &userInput, 1);
}
if (userInput == '1') {
Chip_UART_SendRB(LPC_UART, &txring, (uint8_t *) &uart_interrupt_menu1[0], sizeof(uart_interrupt_menu1));
}
else if (userInput == '2') {
Chip_UART_SendRB(LPC_UART, &txring, (uint8_t *) &uart_interrupt_menu2[0], sizeof(uart_interrupt_menu2));
}
else if (userInput == '3') {
Chip_UART_SendRB(LPC_UART, &txring, (uint8_t *) &uart_interrupt_menu3[0], sizeof(uart_interrupt_menu3));
}
else if (userInput == '4') {
Chip_UART_SendRB(LPC_UART, &txring, (uint8_t *) &uart_interrupt_menu4[0], sizeof(uart_interrupt_menu4));
}
else if (( userInput == 'x') || ( userInput == 'X') ) {
isExit = 1;
}
}
App_Interrupt_DeInit();
}
/**
* @brief Main UART program body
* @return Always returns 1
*/
int main(void)
{
uint8_t key;
int bytes;
SystemCoreClockUpdate();
Board_Init();
Board_UART_Init(LPC_UARTX);
Board_LED_Set(0, false);
/* Setup UART for 115.2K8N1 */
Chip_UART_Init(LPC_UARTX);
Chip_UART_SetBaud(LPC_UARTX, 115200);
Chip_UART_ConfigData(LPC_UARTX, (UART_LCR_WLEN8 | UART_LCR_SBS_1BIT));
Chip_UART_SetupFIFOS(LPC_UARTX, (UART_FCR_FIFO_EN | UART_FCR_TRG_LEV2));
Chip_UART_TXEnable(LPC_UARTX);
/* Before using the ring buffers, initialize them using the ring
buffer init function */
RingBuffer_Init(&rxring, rxbuff, 1, UART_RRB_SIZE);
RingBuffer_Init(&txring, txbuff, 1, UART_SRB_SIZE);
/* Reset and enable FIFOs, FIFO trigger level 3 (14 chars) */
Chip_UART_SetupFIFOS(LPC_UARTX, (UART_FCR_FIFO_EN | UART_FCR_RX_RS |
UART_FCR_TX_RS | UART_FCR_TRG_LEV3));
/* Enable receive data and line status interrupt */
Chip_UART_IntEnable(LPC_UARTX, (UART_IER_RBRINT | UART_IER_RLSINT));
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(UARTx_IRQn, 1);
NVIC_EnableIRQ(UARTx_IRQn);
/* Send initial messages */
Chip_UART_SendRB(LPC_UARTX, &txring, inst1, sizeof(inst1) - 1);
Chip_UART_SendRB(LPC_UARTX, &txring, inst2, sizeof(inst2) - 1);
/* Poll the receive ring buffer for the ESC (ASCII 27) key */
key = 0;
while (key != 27) {
bytes = Chip_UART_ReadRB(LPC_UARTX, &rxring, &key, 1);
if (bytes > 0) {
/* Wrap value back around */
if (Chip_UART_SendRB(LPC_UARTX, &txring, (const uint8_t *) &key, 1) != 1) {
Board_LED_Toggle(0);/* Toggle LED if the TX FIFO is full */
}
}
}
/* DeInitialize UART0 peripheral */
NVIC_DisableIRQ(UARTx_IRQn);
Chip_UART_DeInit(LPC_UARTX);
return 1;
}
/* Print Welcome Screen Menu subroutine by Interrupt mode */
static void Print_Menu_Interrupt(LPC_USART_T *UARTx)
{
uint32_t tmp;
uint8_t *pDat;
tmp = sizeof(uart_interrupt_menu);
pDat = (uint8_t *) &uart_interrupt_menu[0];
Chip_UART_SendRB(UARTx, &txring, pDat, tmp);
}
/* Send data to uart */
uint32_t uart_write(uint8_t *pbuf, uint32_t len)
{
uint32_t ret = 0;
if (pbuf)
ret = Chip_UART_SendRB(LPC_USART, &uart_txrb, pbuf, len);
return ret;
}
/* Send data to uart */
uint32_t UART_Write(uint8_t *pBuf, uint32_t len)
{
uint32_t ret = 0;
if(pBuf)
{
ret = Chip_UART_SendRB(LPC_USART, &uart_txrb, pBuf, len);
}
return ret;
}
static void ether_to_uart(uint8_t sock)
{
uint8_t sock_state;
uint8_t dstip[4];
uint16_t dstport, len = 0;
getsockopt(sock, SO_STATUS, &sock_state);
switch (sock_state) {
case SOCK_UDP:
getsockopt(sock, SO_RECVBUF, &len);
if(len > UART_SRB_SIZE)
len = UART_SRB_SIZE;
if((len > 0) && len <= RingBuffer_GetFree(&txring)) {
len = recvfrom(sock, g_recv_buf, sizeof(g_recv_buf), dstip, &dstport);
if(len < 0) {
//printf("recvfrom error\r\n");
return;
}
ether_recv_cnt += len;
} else
len = 0;
break;
case SOCK_ESTABLISHED:
getsockopt(sock, SO_RECVBUF, &len);
if(len > UART_SRB_SIZE)
len = UART_SRB_SIZE;
if((len > 0) && len <= RingBuffer_GetFree(&txring)) {
len = recv(sock, g_recv_buf, sizeof(g_recv_buf));
if(len < 0) {
//printf("recv error\r\n");
return;
}
ether_recv_cnt += len;
} else
len = 0;
break;
default:
break;
}
if(len) {
Chip_UART_SendRB(UART_DATA, &txring, g_recv_buf, len);
uart_send_cnt += len;
}
}
static void trigger_state3_process(uint8_t sock)
{
if(trigger_flag == 2) {
trigger_state = TRIG_STATE_NONE;
#ifdef __TRIG_DEBUG__
printf("[%s] TRIG_STATE_NONE #1\r\n", __func__);
#endif
trigger_flag = uart_size_prev = 0;
pattern_offset = 0;
disconnect(sock);
UART_buffer_flush(&rxring);
UART_buffer_flush(&txring);
Chip_UART_SendRB(UART_DATA, &txring, "\r\n\r\n\r\n[W,0]\r\n", 13);
Chip_UART_SendRB(UART_DATA, &txring, "[S,0]\r\n", 7);
op_mode = OP_COMMAND;
close(sock);
return;
}
if(pattern_cnt < RingBuffer_GetCount(&rxring)) {
trigger_state = TRIG_STATE_NONE;
#ifdef __TRIG_DEBUG__
printf("[%s] TRIG_STATE_NONE #2\r\n", __func__);
#endif
trigger_flag = trigger_time = uart_size_prev = 0;
}
if(uart_size_prev != RingBuffer_GetCount(&rxring)) {
trigger_state = TRIG_STATE_NONE;
#ifdef __TRIG_DEBUG__
printf("[%s] TRIG_STATE_NONE #3\r\n", __func__);
#endif
trigger_flag = trigger_time = uart_size_prev = 0;
}
}
int uartSend(ciaaUART_e nUART, void * data, int datalen)
{
uartData_t * u = &(uarts[nUART]);
return Chip_UART_SendRB(u->uart, u->trb, data, datalen);
}
uint32_t UART_write(void *data, int bytes)
{
return Chip_UART_SendRB(LPC_USART, &txring, data, bytes);
}
void skynetbase_gps_config(char msg[]) {
Chip_UART_SendRB(GPS_UART, &txring, (void*)msg, strlen(msg));
}
void skynetbase_gps_query(void) {
char tmp[] = "$PUBX,00*33\r\n";
Chip_UART_SendRB(GPS_UART, &txring, (void*)tmp, sizeof(tmp) - 1);
}
/**
* @brief Main UART program body
* @return Always returns 1
*/
int main(void)
{
uint8_t key;
int bytes;
SystemCoreClockUpdate();
Board_Init();
Init_UART_PinMux();
Board_LED_Set(0, false);
/* Before setting up the UART, the global UART clock for USARTS 1-4
must first be setup. This requires setting the UART divider and
the UART base clock rate to 16x the maximum UART rate for all
UARTs. */
#if defined(USE_INTEGER_CLOCK)
/* Use main clock rate as base for UART baud rate divider */
Chip_Clock_SetUARTBaseClockRate(Chip_Clock_GetMainClockRate(), false);
#else
/* Use 128x expected UART baud rate for fractional baud mode. */
Chip_Clock_SetUARTBaseClockRate((115200 * 128), true);
#endif
/* Setup UART */
Chip_UART_Init(LPC_USART);
Chip_UART_ConfigData(LPC_USART, UART_CFG_DATALEN_8 | UART_CFG_PARITY_NONE | UART_CFG_STOPLEN_1);
Chip_UART_SetBaud(LPC_USART, UART_TEST_DEFAULT_BAUDRATE);
/* Optional for low clock rates only: Chip_UART_SetBaudWithRTC32K(LPC_USART, 300); */
Chip_UART_Enable(LPC_USART);
Chip_UART_TXEnable(LPC_USART);
/* Before using the ring buffers, initialize them using the ring
buffer init function */
RingBuffer_Init(&rxring, rxbuff, 1, UART_RB_SIZE);
RingBuffer_Init(&txring, txbuff, 1, UART_RB_SIZE);
/* Enable receive data and line status interrupt */
Chip_UART_IntEnable(LPC_USART, UART_INTEN_RXRDY);
Chip_UART_IntDisable(LPC_USART, UART_INTEN_TXRDY); /* May not be needed */
/* Enable UART interrupt */
NVIC_EnableIRQ(LPC_IRQNUM);
/* Initial message sent using blocking method to prevent ring
buffer overflow */
Chip_UART_SendBlocking(LPC_USART, inst1, sizeof(inst1) - 1);
Chip_UART_SendRB(LPC_USART, &txring, inst2, sizeof(inst2) - 1);
/* Poll the receive ring buffer for the ESC (ASCII 27) key */
key = 0;
while (key != 27) {
bytes = Chip_UART_ReadRB(LPC_USART, &rxring, &key, 1);
if (bytes > 0) {
/* Wrap value back around */
if (Chip_UART_SendRB(LPC_USART, &txring, (const uint8_t *) &key, 1) != 1) {
Board_LED_Toggle(0);/* Toggle LED if the TX FIFO is full */
}
}
}
/* DeInitialize UART peripheral */
NVIC_DisableIRQ(LPC_IRQNUM);
Chip_UART_DeInit(LPC_USART);
return 1;
}
