void AddGerberX2Attribute( PLOTTER * aPlotter,
const BOARD *aBoard, LAYER_NUM aLayer, bool aUseX1CompatibilityMode )
{
AddGerberX2Header( aPlotter, aBoard, aUseX1CompatibilityMode );
wxString text;
// Add the TF.FileFunction
text = GetGerberFileFunctionAttribute( aBoard, aLayer );
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
// Add the TF.FilePolarity (for layers which support that)
text = GetGerberFilePolarityAttribute( aLayer );
if( !text.IsEmpty() )
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
}
void AddGerberX2Attribute( PLOTTER * aPlotter,
const BOARD *aBoard, LAYER_NUM aLayer, bool aUseX1CompatibilityMode )
{
wxString text;
// Creates the TF,.GenerationSoftware. Format is:
// %TF,.GenerationSoftware,<vendor>,<application name>[,<application version>]*%
text.Printf( wxT( "%%TF.GenerationSoftware,KiCad,Pcbnew,%s*%%" ), GetBuildVersion() );
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
// creates the TF.CreationDate ext:
// The attribute value must conform to the full version of the ISO 8601
// date and time format, including time and time zone. Note that this is
// the date the Gerber file was effectively created,
// not the time the project of PCB was started
wxDateTime date( wxDateTime::GetTimeNow() );
// Date format: see http://www.cplusplus.com/reference/ctime/strftime
wxString msg = date.Format( wxT( "%z" ) ); // Extract the time zone offset
// The time zone offset format is + (or -) mm or hhmm (mm = number of minutes, hh = number of hours)
// we want +(or -) hh:mm
if( msg.Len() > 3 )
msg.insert( 3, ":", 1 ),
text.Printf( wxT( "%%TF.CreationDate,%s%s*%%" ), GetChars( date.FormatISOCombined() ), GetChars( msg ) );
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
// Creates the TF,.ProjectId. Format is (from Gerber file format doc):
// %TF.ProjectId,<project id>,<project GUID>,<revision id>*%
// <project id> is the name of the project, restricted to basic ASCII symbols only,
// and comma not accepted
// All illegal chars will be replaced by underscore
// <project GUID> is a 32 hexadecimal digits string which is an unique id of a project.
// This is a random 128-bit number expressed in 32 hexadecimal digits.
// See en.wikipedia.org/wiki/GUID for more information
// However Kicad does not handle such a project GUID, so it is built from the board name
// Rem: <project id> accepts only ASCII 7 code (only basic ASCII codes are allowed in gerber files).
wxFileName fn = aBoard->GetFileName();
msg = fn.GetFullName();
wxString guid;
// Build a 32 digits GUID from the board name:
for( unsigned ii = 0; ii < msg.Len(); ii++ )
{
int cc1 = int( msg[ii] ) & 0x0F;
int cc2 = ( int( msg[ii] ) >> 4) & 0x0F;
guid << wxString::Format( wxT( "%X%X" ), cc2, cc1 );
if( guid.Len() >= 32 )
break;
}
// guid has 32 digits, so add missing digits
int cnt = 32 - guid.Len();
if( cnt > 0 )
guid.Append( '0', cnt );
// build the <project id> string: this is the board short filename (without ext)
// and all non ASCII chars and comma are replaced by '_'
msg = fn.GetName();
msg.Replace( wxT( "," ), wxT( "_" ) );
// build the <rec> string. All non ASCII chars and comma are replaced by '_'
wxString rev = ((BOARD*)aBoard)->GetTitleBlock().GetRevision();
rev.Replace( wxT( "," ), wxT( "_" ) );
if( rev.IsEmpty() )
rev = wxT( "rev?" );
text.Printf( wxT( "%%TF.ProjectId,%s,%s,%s*%%" ), msg.ToAscii(), GetChars( guid ), rev.ToAscii() );
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
// Add the TF.FileFunction
text = GetGerberFileFunctionAttribute( aBoard, aLayer );
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
// Add the TF.FilePolarity (for layers which support that)
text = GetGerberFilePolarityAttribute( aLayer );
if( !text.IsEmpty() )
aPlotter->AddLineToHeader( makeStringCompatX1( text, aUseX1CompatibilityMode ) );
}