ERROR_CODE GetSectorNumber( unsigned long ulAddr, int *pnSector )
{
int nSector = 0;
int i;
int error_code = 1;
unsigned long ulMask; //offset mask
unsigned long ulOffset; //offset
unsigned long ulStartOff;
unsigned long ulEndOff;
ulMask = 0x3fffff;
ulOffset = ulAddr & ulMask;
for(i = 0; i < gNumSectors; i++)
{
GetSectorStartEnd(&ulStartOff, &ulEndOff, i);
if ( (ulOffset >= ulStartOff)
&& (ulOffset <= ulEndOff) )
{
error_code = 0;
nSector = i;
break;
}
}
// if it is a valid sector, set it
if (error_code == 0)
*pnSector = nSector;
// else it is an invalid sector
else
return INVALID_SECTOR;
// ok
return NO_ERR;
}
ERROR_CODE EraseBlock( int nBlock, unsigned long ulAddr )
{
ERROR_CODE ErrorCode = NO_ERR; //tells us if there was an error erasing flash
unsigned long ulSectStart = 0x0; //stores the sector start offset
unsigned long ulSectEnd = 0x0; //stores the sector end offset(however we do not use it here)
unsigned long ulFlashStartAddr; //flash start address
// get flash start address from absolute address
// The ulAddr should ideally be pointing to the flash start
// address. However we just verify it here again.
ulFlashStartAddr = GetFlashStartAddress(ulAddr);
// Get the sector start offset
// we get the end offset too however we do not actually use it for Erase sector
GetSectorStartEnd( &ulSectStart, &ulSectEnd, nBlock );
// send the erase block command to the flash
WriteFlash( (ulFlashStartAddr + 0x0AAA), 0xaa );
WriteFlash( (ulFlashStartAddr + 0x0554), 0x55 );
WriteFlash( (ulFlashStartAddr + 0x0AAA), 0x80 );
WriteFlash( (ulFlashStartAddr + 0x0AAA), 0xaa );
WriteFlash( (ulFlashStartAddr + 0x0554), 0x55 );
// the last write has to be at an address in the block
WriteFlash( (ulFlashStartAddr + ulSectStart), 0x30 );
// poll until the command has completed
ErrorCode = PollToggleBit(ulFlashStartAddr + ulSectStart);
// block erase should be complete
return ErrorCode;
}
unsigned long GetFlashStartAddress( unsigned long ulAddr)
{
ERROR_CODE ErrorCode = NO_ERR; //tells us if there was an error erasing flash
unsigned long ulFlashStartAddr; //flash start address
unsigned long ulSectStartAddr; //sector start address
unsigned long ulSectEndAddr; //sector end address
unsigned long ulMask; //offset mask
// get flash start address from absolute address
GetSectorStartEnd( &ulSectStartAddr, &ulSectEndAddr, (gNumSectors-1));
ulMask = ~(ulSectEndAddr);
ulFlashStartAddr = ulAddr & ulMask;
return(ulFlashStartAddr);
}
ERROR_CODE EraseBlock( int nBlock, unsigned long ulAddr )
{
ERROR_CODE ErrorCode = NO_ERR; //tells us if there was an error erasing flash
unsigned long ulSectStart = 0x0; //stores the sector start offset
unsigned long ulSectEnd = 0x0; //stores the sector end offset(however we do not use it here)
#ifdef LOCK_MAC_ADDR_SECTOR
if ( (nBlock < 0) || (nBlock > gNumSectors) )
return INVALID_BLOCK;
// we do not allow an erase of the last sector because the
// MAC address is stored at this location
if ( nBlock == (gNumSectors - 1) )
return NO_ACCESS_SECTOR;
#else
if ( (nBlock < 0) || (nBlock > gNumSectors) )
return INVALID_BLOCK;
#endif
// Get the sector start offset
// we get the end offset too however we do not actually use it for Erase sector
GetSectorStartEnd( &ulSectStart, &ulSectEnd, nBlock );
// send the erase block command to the flash
WriteFlash( (ulAddr + 0x0AAA), 0xaa );
WriteFlash( (ulAddr + 0x0554), 0x55 );
WriteFlash( (ulAddr + 0x0AAA), 0x80 );
WriteFlash( (ulAddr + 0x0AAA), 0xaa );
WriteFlash( (ulAddr + 0x0554), 0x55 );
// the last write has to be at an address in the block
WriteFlash( (ulAddr + ulSectStart), 0x30 );
// poll until the command has completed
ErrorCode = PollToggleBit(ulAddr + ulSectStart);
// block erase should be complete
return ErrorCode;
}
u32 adi_pdd_Control( ADI_DEV_PDD_HANDLE PDDHandle,
u32 Command,
void *pArg)
{
ERROR_CODE ErrorCode = NO_ERR;
COMMAND_STRUCT *pCmdStruct = (COMMAND_STRUCT *)pArg;
// switch on the command
switch ( Command )
{
// erase all
case CNTRL_ERASE_ALL:
ErrorCode = EraseFlash(pCmdStruct->SEraseAll.ulFlashStartAddr);
break;
// erase sector
case CNTRL_ERASE_SECT:
ErrorCode = EraseBlock( pCmdStruct->SEraseSect.nSectorNum, pCmdStruct->SEraseSect.ulFlashStartAddr );
break;
// get manufacturer and device codes
case CNTRL_GET_CODES:
ErrorCode = GetCodes((int *)pCmdStruct->SGetCodes.pManCode, (int *)pCmdStruct->SGetCodes.pDevCode, (unsigned long)pCmdStruct->SGetCodes.ulFlashStartAddr);
break;
case CNTRL_GET_DESC:
//Filling the contents with data
pCmdStruct->SGetDesc.pDesc = pFlashDesc;
pCmdStruct->SGetDesc.pFlashCompany = pDeviceCompany;
break;
// get sector number based on address
case CNTRL_GET_SECTNUM:
ErrorCode = GetSectorNumber( pCmdStruct->SGetSectNum.ulOffset, (int *)pCmdStruct->SGetSectNum.pSectorNum );
break;
// get sector number start and end offset
case CNTRL_GET_SECSTARTEND:
ErrorCode = GetSectorStartEnd( pCmdStruct->SSectStartEnd.pStartOffset, pCmdStruct->SSectStartEnd.pEndOffset, pCmdStruct->SSectStartEnd.nSectorNum );
break;
// get the number of sectors
case CNTRL_GETNUM_SECTORS:
pCmdStruct->SGetNumSectors.pnNumSectors[0] = gNumSectors;
break;
// reset
case CNTRL_RESET:
ErrorCode = ResetFlash(pCmdStruct->SReset.ulFlashStartAddr);
break;
// turn on dataflow (command required of all device drivers)
case ADI_DEV_CMD_SET_DATAFLOW:
ErrorCode = NO_ERR;
break;
case ADI_DEV_CMD_SET_DATAFLOW_METHOD:
// Do nothing & simply return back for these commands
break;
// get peripheral DMA support (command required of all device drivers)
case ADI_DEV_CMD_GET_PERIPHERAL_DMA_SUPPORT:
(*(u32 *)pArg) = FALSE; // no, this device is not supported by peripheral DMA
break;
// no command or unknown command do nothing
default:
// set our error
ErrorCode = UNKNOWN_COMMAND;
break;
}
// return
return(ErrorCode);
}
u32 adi_pdd_Control( ADI_DEV_PDD_HANDLE PDDHandle,
u32 Command,
void *pArg)
{
ERROR_CODE ErrorCode = NO_ERR;
COMMAND_STRUCT *pCmdStruct = (COMMAND_STRUCT *)pArg;
// switch on the command
switch ( Command )
{
// erase all
case CNTRL_ERASE_ALL:
ErrorCode = EraseFlash(pCmdStruct->SEraseAll.ulFlashStartAddr);
break;
// erase sector
case CNTRL_ERASE_SECT:
ErrorCode = EraseBlock( pCmdStruct->SEraseSect.nSectorNum, pCmdStruct->SEraseSect.ulFlashStartAddr );
break;
// get manufacturer and device codes
case CNTRL_GET_CODES:
ErrorCode = GetCodes((int *)pCmdStruct->SGetCodes.pManCode, (int *)pCmdStruct->SGetCodes.pDevCode, (unsigned long)pCmdStruct->SGetCodes.ulFlashStartAddr);
break;
//Filling the contents with data
case CNTRL_GET_DESC:
pCmdStruct->SGetDesc.pTitle = pEzKitTitle;
pCmdStruct->SGetDesc.pDesc = pFlashDesc;
pCmdStruct->SGetDesc.pFlashCompany = pDeviceCompany;
break;
// get sector number based on address
case CNTRL_GET_SECTNUM:
ErrorCode = GetSectorNumber( pCmdStruct->SGetSectNum.ulOffset, (int *)pCmdStruct->SGetSectNum.pSectorNum );
break;
// get sector number start and end offset
case CNTRL_GET_SECSTARTEND:
ErrorCode = GetSectorStartEnd( pCmdStruct->SSectStartEnd.pStartOffset, pCmdStruct->SSectStartEnd.pEndOffset, pCmdStruct->SSectStartEnd.nSectorNum );
break;
// get the number of sectors
case CNTRL_GETNUM_SECTORS:
pCmdStruct->SGetNumSectors.pnNumSectors[0] = NUM_SECTORS;
break;
// reset
case CNTRL_RESET:
ErrorCode = ResetFlash(pCmdStruct->SReset.ulFlashStartAddr);
break;
// no command or unknown command do nothing
default:
// set our error
ErrorCode = UNKNOWN_COMMAND;
break;
}
// return
return(ErrorCode);
}
