/* I2C1 init function */
static void MX_I2C1_Init(void)
{
hi2c1.Instance = I2C1;
hi2c1.Init.Timing = 0x2000090E;
hi2c1.Init.OwnAddress1 = 0;
hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
hi2c1.Init.OwnAddress2 = 0;
hi2c1.Init.OwnAddress2Masks = I2C_OA2_NOMASK;
hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if (HAL_I2C_Init(&hi2c1) != HAL_OK)
{
_Error_Handler(__FILE__, __LINE__);
}
/**Configure Analogue filter
*/
if (HAL_I2CEx_ConfigAnalogFilter(&hi2c1, I2C_ANALOGFILTER_ENABLE) != HAL_OK)
{
_Error_Handler(__FILE__, __LINE__);
}
/**Configure Digital filter
*/
if (HAL_I2CEx_ConfigDigitalFilter(&hi2c1, 0) != HAL_OK)
{
_Error_Handler(__FILE__, __LINE__);
}
}
/* I2C2 init function */
void MX_I2C2_Init(void)
{
hi2c2.Instance = I2C2;
hi2c2.Init.Timing = 0x20303E5D;
hi2c2.Init.OwnAddress1 = 0;
hi2c2.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
hi2c2.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
hi2c2.Init.OwnAddress2 = 0;
hi2c2.Init.OwnAddress2Masks = I2C_OA2_NOMASK;
hi2c2.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
hi2c2.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if (HAL_I2C_Init(&hi2c2) != HAL_OK)
{
Error_Handler();
}
/**Configure Analogue filter
*/
if (HAL_I2CEx_ConfigAnalogFilter(&hi2c2, I2C_ANALOGFILTER_ENABLE) != HAL_OK)
{
Error_Handler();
}
}
/**
* @brief I2C MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param[in] hi2c I2C handle pointer
* @retval None
*/
void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c)
{
GPIO_InitTypeDef GPIO_InitStruct;
if (hi2c->Instance == BSP_MISC_I2C)
{
/* I2C and GPIOs clock enable */
__BSP_MISC_I2C_CLK_ENABLE();
__BSP_MISC_I2C_SCL_GPIO_CLK_ENABLE();
__BSP_MISC_I2C_SDA_GPIO_CLK_ENABLE();
/* I2C GPIO configuration */
GPIO_InitStruct.Pin = BSP_MISC_I2C_SCL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Alternate = BSP_MISC_AFx_I2C;
HAL_GPIO_Init(BSP_MISC_I2C_SCL_PORT, &GPIO_InitStruct);
GPIO_InitStruct.Pin = BSP_MISC_I2C_SDA_PIN;
HAL_GPIO_Init(BSP_MISC_I2C_SDA_PORT, &GPIO_InitStruct);
/* I2C settings */
hi2c->Init.ClockSpeed = BSP_MISC_I2C_CLOCK_SPEED;
hi2c->Init.DutyCycle = I2C_DUTYCYCLE_2;
hi2c->Init.OwnAddress1 = 0;
hi2c->Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
hi2c->Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
hi2c->Init.OwnAddress2 = 0;
hi2c->Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
hi2c->Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
/* I2C filtering */
HAL_I2CEx_ConfigAnalogFilter(hi2c, I2C_ANALOGFILTER_ENABLE);
}
}
/* I2C1 init function */
void MX_I2C1_Init(void)
{
hi2c1.Instance = I2C1;
hi2c1.Init.Timing = 0x20303E5D;
hi2c1.Init.OwnAddress1 = 0;
hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
hi2c1.Init.OwnAddress2 = 0;
hi2c1.Init.OwnAddress2Masks = I2C_OA2_NOMASK;
hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
HAL_I2C_Init(&hi2c1);
/**Configure Analogue filter
*/
HAL_I2CEx_ConfigAnalogFilter(&hi2c1, I2C_ANALOGFILTER_ENABLE);
}
/* I2C1 init function */
static void MX_I2C1_Init(void)
{
hi2c1.Instance = I2C1;
// hi2c1.Init.Timing = 0x2000090E;
hi2c1.Init.Timing =
(1 << I2C_TIMINGR_PRESC_Pos) |
(0x13 << I2C_TIMINGR_SCLL_Pos) |
(0x0F << I2C_TIMINGR_SCLH_Pos) |
(0x2 << I2C_TIMINGR_SDADEL_Pos) |
(0x4 << I2C_TIMINGR_SCLDEL_Pos) ;
hi2c1.Init.OwnAddress1 = I2C_SLAVE_ADDR << 1;
hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
hi2c1.Init.OwnAddress2 = 0;
hi2c1.Init.OwnAddress2Masks = I2C_OA2_NOMASK;
hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if (HAL_I2C_Init(&hi2c1) != HAL_OK)
{
Error_Handler();
}
/**Configure Analogue filter
*/
if (HAL_I2CEx_ConfigAnalogFilter(&hi2c1, I2C_ANALOGFILTER_ENABLE) != HAL_OK)
{
Error_Handler();
}
uart_printf("i2c init..\r\n");
HAL_I2C_Init(&hi2c1);
uart_printf("i2c init done..\r\n");
}
void i2cInit(I2CDevice device)
{
/*## Configure the I2C clock source. The clock is derived from the SYSCLK #*/
// RCC_PeriphCLKInitTypeDef RCC_PeriphCLKInitStruct;
// RCC_PeriphCLKInitStruct.PeriphClockSelection = i2cHardwareMap[device].clk;
// RCC_PeriphCLKInitStruct.I2c1ClockSelection = i2cHardwareMap[device].clk_src;
// HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphCLKInitStruct);
switch (device) {
case I2CDEV_1:
__HAL_RCC_I2C1_CLK_ENABLE();
break;
case I2CDEV_2:
__HAL_RCC_I2C2_CLK_ENABLE();
break;
case I2CDEV_3:
__HAL_RCC_I2C3_CLK_ENABLE();
break;
case I2CDEV_4:
__HAL_RCC_I2C4_CLK_ENABLE();
break;
default:
break;
}
if (device == I2CINVALID)
return;
i2cDevice_t *i2c;
i2c = &(i2cHardwareMap[device]);
//I2C_InitTypeDef i2cInit;
IO_t scl = IOGetByTag(i2c->scl);
IO_t sda = IOGetByTag(i2c->sda);
IOInit(scl, OWNER_I2C_SCL, RESOURCE_INDEX(device));
IOInit(sda, OWNER_I2C_SDA, RESOURCE_INDEX(device));
// Enable RCC
RCC_ClockCmd(i2c->rcc, ENABLE);
i2cUnstick(scl, sda);
// Init pins
#ifdef STM32F7
IOConfigGPIOAF(scl, IOCFG_I2C, i2c->af);
IOConfigGPIOAF(sda, IOCFG_I2C, i2c->af);
#else
IOConfigGPIO(scl, IOCFG_AF_OD);
IOConfigGPIO(sda, IOCFG_AF_OD);
#endif
// Init I2C peripheral
HAL_I2C_DeInit(&i2cHandle[device].Handle);
i2cHandle[device].Handle.Instance = i2cHardwareMap[device].dev;
/// TODO: HAL check if I2C timing is correct
i2cHandle[device].Handle.Init.Timing = 0x00B01B59;
//i2cHandle[device].Handle.Init.Timing = 0x00D00E28; /* (Rise time = 120ns, Fall time = 25ns) */
i2cHandle[device].Handle.Init.OwnAddress1 = 0x0;
i2cHandle[device].Handle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
i2cHandle[device].Handle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
i2cHandle[device].Handle.Init.OwnAddress2 = 0x0;
i2cHandle[device].Handle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
i2cHandle[device].Handle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
HAL_I2C_Init(&i2cHandle[device].Handle);
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&i2cHandle[device].Handle,I2C_ANALOGFILTER_ENABLE);
HAL_NVIC_SetPriority(i2cHardwareMap[device].er_irq, NVIC_PRIORITY_BASE(NVIC_PRIO_I2C_ER), NVIC_PRIORITY_SUB(NVIC_PRIO_I2C_ER));
HAL_NVIC_EnableIRQ(i2cHardwareMap[device].er_irq);
HAL_NVIC_SetPriority(i2cHardwareMap[device].ev_irq, NVIC_PRIORITY_BASE(NVIC_PRIO_I2C_EV), NVIC_PRIORITY_SUB(NVIC_PRIO_I2C_EV));
HAL_NVIC_EnableIRQ(i2cHardwareMap[device].ev_irq);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/* Configure LED1, LED3 and LED4*/
BSP_LED_Init(LED1);
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
#ifdef MASTER_BOARD
/* Configure Tamper push-button */
BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_GPIO);
/* Wait for Tamper push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_TAMPER) != GPIO_PIN_RESET)
{
}
/* Wait for Tamper push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_TAMPER) != GPIO_PIN_SET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Wait for Tamper push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_TAMPER) != GPIO_PIN_RESET)
{
}
/* Wait for Tamper push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_TAMPER) != GPIO_PIN_SET)
{
}
/*##-4- Put I2C peripheral in reception process ###########################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
#else
/*##-2- Enable I2C peripheral in wake up from stop mode ###################*/
HAL_I2CEx_EnableWakeUp(&I2cHandle);
/*##-3- Put I2C peripheral in reception process ###########################*/
if(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* enter stop mode */
/* Turn LED4 on */
BSP_LED_On(LED4);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
/* Wake Up from Stop mode */
/* Turn LED4 off */
BSP_LED_Off(LED4);
/*##-4- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-5- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* enter stop mode */
/* Turn LED4 on */
BSP_LED_On(LED4);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
/* Wake Up from Stop mode */
/* Turn LED4 off */
BSP_LED_Off(LED4);
#endif /* MASTER_BOARD */
/*##-6- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-7- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/* Configure LED_GREEN and LED_RED */
BSP_LED_Init(LED_GREEN);
BSP_LED_Init(LED_RED);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_10BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
#ifdef MASTER_BOARD
/* Configure User Button*/
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
/* Wait for User Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for User Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
/* Timeout is set to 10S */
while(HAL_I2C_Master_Transmit(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Turn LED_GREEN on: Transfer in Transmission process is correct */
BSP_LED_On(LED_GREEN);
/* Wait for User Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for User Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/*##-3- Put I2C peripheral in reception process ############################*/
/* Timeout is set to 10S */
while(HAL_I2C_Master_Receive(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Turn LED_GREEN off: Transfer in reception process is correct */
BSP_LED_Off(LED_GREEN);
#else
/* The board receives the message and sends it back */
/*##-2- Put I2C peripheral in reception process ############################*/
/* Timeout is set to 10S */
if(HAL_I2C_Slave_Receive(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
{
/* Transfer error in reception process */
Error_Handler();
}
/* Turn LED_GREEN on: Transfer in reception process is correct */
BSP_LED_On(LED_GREEN);
/*##-3- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
/* Timeout is set to 10S */
if(HAL_I2C_Slave_Transmit(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* Turn LED_GREEN off: Transfer in transmission process is correct */
BSP_LED_Off(LED_GREEN);
#endif /* MASTER_BOARD */
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 72 MHz */
SystemClock_Config();
/* Configure LED1, LED2 and LED3 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = EEPROM_TIMING;
I2cHandle.Init.OwnAddress1 = 0x00;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0x00;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
/* The board sends the message to EEPROM then reads it back */
/*##-2- Start writing process ##############################################*/
/* Initialize Remaining Bytes Value to TX Buffer Size */
Remaining_Bytes = TXBUFFERSIZE;
/* Initialize Memory address to 0 since EEPROM write will start from address 0 */
Memory_Address = 0;
/* Since page size is 128 bytes, the write procedure will be done in a loop */
while(Remaining_Bytes > 0)
{
/* Write EEPROM_PAGESIZE */
if(HAL_I2C_Mem_Write_DMA(&I2cHandle , (uint16_t)EEPROM_ADDRESS, Memory_Address, I2C_MEMADD_SIZE_16BIT, (uint8_t*)(aTxBuffer + Memory_Address), EEPROM_PAGESIZE)!= HAL_OK)
{
/* Writing process Error */
Error_Handler();
}
/* Wait for the end of the transfer */
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check if the EEPROM is ready for a new operation */
while (HAL_I2C_IsDeviceReady(&I2cHandle, EEPROM_ADDRESS, 10, 300) == HAL_TIMEOUT);
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Update Remaining bytes and Memory Address values */
Remaining_Bytes -= EEPROM_PAGESIZE;
Memory_Address += EEPROM_PAGESIZE;
}
/*##-3- Start reading process ##############################################*/
if(HAL_I2C_Mem_Read_DMA(&I2cHandle , (uint16_t)EEPROM_ADDRESS, 0, I2C_MEMADD_SIZE_16BIT, (uint8_t*)aRxBuffer, RXBUFFERSIZE)!= HAL_OK)
{
/* Reading process Error */
Error_Handler();
}
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer, (uint8_t*)aRxBuffer, RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
#ifdef MASTER_BOARD
GPIO_InitTypeDef GPIO_InitStruct;
#endif
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 64 MHz */
SystemClock_Config();
/* Configure LED3 and LED3*/
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
#ifdef MASTER_BOARD
/* Configure PA.12 (Arduino D2) button */
GPIO_InitStruct.Pin = GPIO_PIN_12;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
/* Enable GPIOA clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Wait Until PA.12 (Arduino D2) is connected to GND */
while(HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_12) != GPIO_PIN_RESET)
{
}
/* Wait Until PA.12 (Arduino D2) is de-connected from GND */
while(HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_12) != GPIO_PIN_SET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge its address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
HAL_Delay(1000);
/* Wait Until PA.12 (Arduino D2) is connected to GND */
while(HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_12) != GPIO_PIN_RESET)
{
}
/* Wait Until PA.12 (Arduino D2) is de-connected from GND */
while(HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_12) != GPIO_PIN_SET)
{
}
/*##-4- Put I2C peripheral in reception process ###########################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
#else
/*##-2- Enable I2C peripheral in wake up from stop mode ###################*/
HAL_I2CEx_EnableWakeUp(&I2cHandle);
/*##-3- Put I2C peripheral in reception process ###########################*/
if(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Transfer error in reception process */
Error_Handler();
}
/* enter stop mode */
/* Configure the WakeUp clock source */
/* Enable Power Control clock */
__HAL_RCC_PWR_CLK_ENABLE();
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
/*##-4- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-5- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
/* Disable Power Control clock */
__HAL_RCC_PWR_CLK_DISABLE();
#endif /* MASTER_BOARD */
/*##-6- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-7- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/* Configure LED3 and LED4 */
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART configured as follows:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
/* Configure User push-button Button*/
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
do{
/* Wait for User push-button Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for User push-button Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
void ndef_test(void);
float get_adc(void);
ndef_test();
//get_adc();
}while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 72 MHz */
SystemClock_Config();
/* Configure LED1 and LED3 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
#ifdef MASTER_BOARD
/* Configure Key Button*/
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/* Wait for Key Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_RESET)
{
}
/* Wait for Key Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_SET)
{
}
while(1)
{
/* Initialize number of data variables */
hTxNumData = TXBUFFERSIZE;
hRxNumData = RXBUFFERSIZE;
/* Update bTransferRequest to send buffer write request for Slave */
bTransferRequest = MASTER_REQ_WRITE;
/*##-2- Master sends write request for slave #############################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-3- Master sends number of data to be written ########################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&hTxNumData, 2)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Master sends aTxBuffer to slave ##################################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Update bTransferRequest to send buffer read request for Slave */
bTransferRequest = MASTER_REQ_READ;
/*##-5- Master sends read request for slave ##############################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-6- Master sends number of data to be read ###########################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&hRxNumData, 2)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-7- Master receives aRxBuffer from slave #############################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aRxBuffer, RXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check correctness of received buffer ##################################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,hRxNumData))
{
/* Processing Error */
Error_Handler();
}
/* Flush Rx buffers */
Flush_Buffer((uint8_t*)aRxBuffer,RXBUFFERSIZE);
/* Toggle LED1 */
BSP_LED_Toggle(LED1);
/* This delay permit the key to see LED3 toggling */
HAL_Delay(25);
}
#else
while(1)
{
/* Initialize number of data variables */
hTxNumData = 0;
hRxNumData = 0;
/*##-2- Slave receive request from master ################################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
{
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* If master request write operation #####################################*/
if (bTransferRequest == MASTER_REQ_WRITE)
{
/*##-3- Slave receive number of data to be read ########################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)&hRxNumData, 2)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Slave receives aRxBuffer from master ###########################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)aRxBuffer, hRxNumData)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check correctness of received buffer ################################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,hRxNumData))
{
/* Processing Error */
Error_Handler();
}
/* Flush Rx buffers */
Flush_Buffer((uint8_t*)aRxBuffer,RXBUFFERSIZE);
/* Toggle LED1 */
BSP_LED_Toggle(LED1);
}
/* If master request write operation #####################################*/
else
{
/*##-3- Slave receive number of data to be written #####################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)&hTxNumData, 2)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Slave transmit aTxBuffer to master #############################*/
while(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, RXBUFFERSIZE)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
}
}
#endif /* MASTER_BOARD */
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 64 MHz */
SystemClock_Config();
/* Configure LED1 and LED3 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_10BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
#ifdef MASTER_BOARD
/* Configure User push-button button */
BSP_PB_Init(BUTTON_USER,BUTTON_MODE_GPIO);
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/* Delay to avoid that possible signal rebound is taken as button release */
HAL_Delay(50);
/* Wait for User push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge its address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/* Delay to avoid that possible signal rebound is taken as button release */
HAL_Delay(50);
/* Wait for User push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/*##-4- Put I2C peripheral in reception process ###########################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
#else
/* The board receives the message and sends it back */
/*##-2- Put I2C peripheral in reception process ###########################*/
if(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Transfer error in reception process */
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
#endif /* MASTER_BOARD */
/*##-5- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-6- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
void i2cInit(I2CDevice device)
{
if (device == I2CINVALID) {
return;
}
i2cDevice_t *pDev = &i2cDevice[device];
const i2cHardware_t *hardware = pDev->hardware;
if (!hardware) {
return;
}
IO_t scl = pDev->scl;
IO_t sda = pDev->sda;
IOInit(scl, OWNER_I2C_SCL, RESOURCE_INDEX(device));
IOInit(sda, OWNER_I2C_SDA, RESOURCE_INDEX(device));
// Enable RCC
RCC_ClockCmd(hardware->rcc, ENABLE);
i2cUnstick(scl, sda);
// Init pins
#ifdef STM32F7
IOConfigGPIOAF(scl, pDev->pullUp ? IOCFG_I2C_PU : IOCFG_I2C, GPIO_AF4_I2C);
IOConfigGPIOAF(sda, pDev->pullUp ? IOCFG_I2C_PU : IOCFG_I2C, GPIO_AF4_I2C);
#else
IOConfigGPIO(scl, IOCFG_AF_OD);
IOConfigGPIO(sda, IOCFG_AF_OD);
#endif
// Init I2C peripheral
I2C_HandleTypeDef *pHandle = &pDev->handle;
memset(pHandle, 0, sizeof(*pHandle));
pHandle->Instance = pDev->hardware->reg;
/// TODO: HAL check if I2C timing is correct
if (pDev->overClock) {
// 800khz Maximum speed tested on various boards without issues
pHandle->Init.Timing = 0x00500D1D;
} else {
pHandle->Init.Timing = 0x00500C6F;
}
pHandle->Init.OwnAddress1 = 0x0;
pHandle->Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
pHandle->Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
pHandle->Init.OwnAddress2 = 0x0;
pHandle->Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
pHandle->Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
HAL_I2C_Init(pHandle);
// Enable the Analog I2C Filter
HAL_I2CEx_ConfigAnalogFilter(pHandle, I2C_ANALOGFILTER_ENABLE);
// Setup interrupt handlers
HAL_NVIC_SetPriority(hardware->er_irq, NVIC_PRIORITY_BASE(NVIC_PRIO_I2C_ER), NVIC_PRIORITY_SUB(NVIC_PRIO_I2C_ER));
HAL_NVIC_EnableIRQ(hardware->er_irq);
HAL_NVIC_SetPriority(hardware->ev_irq, NVIC_PRIORITY_BASE(NVIC_PRIO_I2C_EV), NVIC_PRIORITY_SUB(NVIC_PRIO_I2C_EV));
HAL_NVIC_EnableIRQ(hardware->ev_irq);
}
