VOID APMakeAllBssBeacon(RTMP_ADAPTER *pAd)
{
INT i;
UCHAR NumOfBcns;
/* choose the Beacon number */
NumOfBcns = GetBcnNum(pAd);
#if defined(RTMP_MAC) || defined(RLT_MAC)
if ((pAd->chipCap.hif_type == HIF_RTMP) || (pAd->chipCap.hif_type == HIF_RLT)) {
INT j;
/*
before MakeBssBeacon, clear all beacon TxD's valid bit
Note: can not use MAX_MBSSID_NUM here, or
1. when MBSS_SUPPORT is enabled;
2. MAX_MBSSID_NUM will be 8;
3. if HW_BEACON_OFFSET is 0x0200,
we will overwrite other shared memory of chip.
use pAd->ApCfg.BssidNum to avoid the case is best
*/
UINT8 TXWISize = pAd->chipCap.TXWISize;
for (i=0; i<HW_BEACON_MAX_COUNT(pAd); i++)
{
for (j=0; j < TXWISize; j+=4)
{
RTMP_CHIP_UPDATE_BEACON(pAd, pAd->BeaconOffset[i] + j, 0, 4);
}
}
}
#endif /* defined(RTMP_MAC) || defined(RLT_MAC) */
for(i=0; i<pAd->ApCfg.BssidNum; i++)
APMakeBssBeacon(pAd, i);
AsicSetMbssMode(pAd, NumOfBcns);
}
VOID APMakeAllBssBeacon(
IN PRTMP_ADAPTER pAd)
{
INT i, j;
UINT32 regValue;
UCHAR NumOfMacs;
UCHAR NumOfBcns;
UINT8 TXWISize = pAd->chipCap.TXWISize;
/* before MakeBssBeacon, clear all beacon TxD's valid bit */
/* Note: can not use MAX_MBSSID_NUM here, or
1. when MBSS_SUPPORT is enabled;
2. MAX_MBSSID_NUM will be 8;
3. if HW_BEACON_OFFSET is 0x0200,
we will overwrite other shared memory SRAM of chip */
/* use pAd->ApCfg.BssidNum to avoid the case is best */
/* choose the Beacon number */
NumOfBcns = GetBcnNum(pAd);
for (i=0; i<HW_BEACON_MAX_COUNT(pAd); i++)
{
for (j=0; j < TXWISize; j+=4)
{
RTMP_CHIP_UPDATE_BEACON(pAd, pAd->BeaconOffset[i] + j, 0, 4);
}
}
for(i=0; i<pAd->ApCfg.BssidNum; i++)
{
APMakeBssBeacon(pAd, i);
}
RTMP_IO_READ32(pAd, MAC_BSSID_DW1, ®Value);
regValue &= 0x0000FFFF;
/*
Note:
1.The MAC address of Mesh and AP-Client link are different from Main BSSID.
2.If the Mesh link is included, its MAC address shall follow the last MBSSID's MAC by increasing 1.
3.If the AP-Client link is included, its MAC address shall follow the Mesh interface MAC by increasing 1.
*/
NumOfMacs = pAd->ApCfg.BssidNum + MAX_MESH_NUM + MAX_APCLI_NUM;
/* set Multiple BSSID mode */
if (NumOfMacs <= 1)
{
pAd->ApCfg.MacMask = ~(1-1);
/*regValue |= 0x0; */
}
else if (NumOfMacs <= 2)
{
if ((pAd->CurrentAddress[5] % 2 != 0)
)
DBGPRINT(RT_DEBUG_ERROR, ("The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2\n"));
regValue |= (1<<16);
pAd->ApCfg.MacMask = ~(2-1);
}
else if (NumOfMacs <= 4)
{
if (pAd->CurrentAddress[5] % 4 != 0)
DBGPRINT(RT_DEBUG_ERROR, ("The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4\n"));
regValue |= (2<<16);
pAd->ApCfg.MacMask = ~(4-1);
}
else if (NumOfMacs <= 8)
{
if (pAd->CurrentAddress[5] % 8 != 0)
DBGPRINT(RT_DEBUG_ERROR, ("The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8\n"));
regValue |= (3<<16);
pAd->ApCfg.MacMask = ~(8-1);
}
else if (NumOfMacs <= 16)
{
/* Set MULTI_BSSID_MODE_BIT4 in MAC register 0x1014 */
regValue |= (1<<22);
pAd->ApCfg.MacMask = ~(16-1);
}
/* set Multiple BSSID Beacon number */
if (NumOfBcns > 1)
{
if (NumOfBcns > 8)
regValue |= (((NumOfBcns - 1) >> 3) << 23);
regValue |= (((NumOfBcns - 1) & 0x7) << 18);
}
/* set as 0/1 bit-21 of MAC_BSSID_DW1(offset: 0x1014)
to disable/enable the new MAC address assignment. */
if (pAd->chipCap.MBSSIDMode >= MBSSID_MODE1)
{
regValue |= (1 << 21);
#ifdef ENHANCE_NEW_MBSSID_MODE
if (pAd->chipCap.MBSSIDMode == MBSSID_MODE2)
regValue |= (1 << 24);
else if (pAd->chipCap.MBSSIDMode == MBSSID_MODE3)
regValue |= (2 << 24);
else if (pAd->chipCap.MBSSIDMode == MBSSID_MODE4)
regValue |= (3 << 24);
else if (pAd->chipCap.MBSSIDMode == MBSSID_MODE5)
regValue |= (4 << 24);
else if (pAd->chipCap.MBSSIDMode == MBSSID_MODE6)
regValue |= (5 << 24);
#endif /* ENHANCE_NEW_MBSSID_MODE */
}
RTMP_IO_WRITE32(pAd, MAC_BSSID_DW1, regValue);
#ifdef HDR_TRANS_SUPPORT
/*
point WCID MAC table to 0x1800
This is for debug.
But HDR_TRANS doesn't work if you remove it.
Check after IC formal release.
*/
regValue |= 0x18000000;
RTMP_IO_WRITE32(pAd, HT_MAC_BSSID_DW1, regValue);
#endif /* HDR_TRANS_SUPPORT */
}
