/**
* @brief mpu6050_init
* @param void
* @retval 成功为0
* @note 初始化mpu6050 频率为100*1000HZ
*/
int16_t mpu6050_init(void)
{
I2C_QuickInit(I2C0_SCL_PB02_SDA_PB03,100*1000);
int result=0;
result=mpu_init();
if(!result)
{
PrintChar("mpu initialization complete......\n "); //mpu initialization complete
if(!mpu_set_sensors(INV_XYZ_GYRO | INV_XYZ_ACCEL)) //mpu_set_sensor
PrintChar("mpu_set_sensor complete ......\n");
else
PrintChar("mpu_set_sensor come across error ......\n");
if(!mpu_configure_fifo(INV_XYZ_GYRO | INV_XYZ_ACCEL)) //mpu_configure_fifo
PrintChar("mpu_configure_fifo complete ......\n");
else
PrintChar("mpu_configure_fifo come across error ......\n");
if(!mpu_set_sample_rate(DEFAULT_MPU_HZ)) //mpu_set_sample_rate
PrintChar("mpu_set_sample_rate complete ......\n");
else
PrintChar("mpu_set_sample_rate error ......\n");
if(!dmp_load_motion_driver_firmware()) //dmp_load_motion_driver_firmvare
PrintChar("dmp_load_motion_driver_firmware complete ......\n");
else
PrintChar("dmp_load_motion_driver_firmware come across error ......\n");
if(!dmp_set_orientation(inv_orientation_matrix_to_scalar(gyro_orientation))) //dmp_set_orientation
PrintChar("dmp_set_orientation complete ......\n");
else
PrintChar("dmp_set_orientation come across error ......\n");
if(!dmp_enable_feature(DMP_FEATURE_6X_LP_QUAT | DMP_FEATURE_TAP |
DMP_FEATURE_ANDROID_ORIENT | DMP_FEATURE_SEND_RAW_ACCEL | DMP_FEATURE_SEND_CAL_GYRO |
DMP_FEATURE_GYRO_CAL)) //dmp_enable_feature
PrintChar("dmp_enable_feature complete ......\n");
else
PrintChar("dmp_enable_feature come across error ......\n");
if(!dmp_set_fifo_rate(DEFAULT_MPU_HZ)) //dmp_set_fifo_rate
PrintChar("dmp_set_fifo_rate complete ......\n");
else
PrintChar("dmp_set_fifo_rate come across error ......\n");
run_self_test(); //自检
if(!mpu_set_dmp_state(1))
PrintChar("mpu_set_dmp_state complete ......\n");
else
PrintChar("mpu_set_dmp_state come across error ......\n");
}
return 0;
}
void SCCB_Init(void)
{
I2C_QuickInit(I2C0_SCL_PB00_SDA_PB01, 100*1000);
/* 只是复位 全部做默认设置 */
/* Yandld: 如果是默认出厂配置, 则无需配置SCCB */
OV7620_Reset();
DelayMs(10);
/* 默认配置如下 */
/* 0x12,0x64
0x06,0xA0
0x03,0x80 */
}
/**
* \brief i2c bus scan test
* @param[in] MAP I2C引脚配置缩略图,详见i2c.h
* \retval None
*/
void I2C_Scan(uint32_t MAP)
{
uint8_t i;
uint8_t ret;
uint32_t instance;
instance = I2C_QuickInit(MAP, 100*1000);
for(i = 1; i < 127; i++)
{
ret = I2C_Probe(instance , i);
if(!ret)
{
LIB_TRACE("ADDR:0x%2X(7BIT) | 0x%2X(8BIT) found!\r\n", i, i<<1);
}
}
}
int SCCB_Init(uint32_t I2C_MAP)
{
int r;
uint32_t instance;
instance = I2C_QuickInit(I2C_MAP, 50*1000);
r = ov7725_probe(instance);
if(r)
{
return 1;
}
r = ov7725_set_image_size(IMAGE_SIZE);
if(r)
{
printf("OV7725 set image error\r\n");
return 1;
}
return 0;
}
int main(void)
{
int i;
DelayInit();
GPIO_QuickInit(HW_GPIOE, 6, kGPIO_Mode_OPP);
UART_QuickInit(UART0_RX_PA01_TX_PA02, 115200);
/** print message before mode change*/
printf("i2s MAPSK64 test\r\n");
I2C_QuickInit(I2C0_SCL_PE24_SDA_PE25, 100*1000);
// I2C_Scan(I2C0_SCL_PE24_SDA_PE25);
wm8960_init(0);
wm8960_format_config(44100, 16);
// wm8960_set_volume(kWolfsonModuleHP, 0x2FFF);
I2S_InitTypeDef Init;
Init.instance = 0;
Init.isStereo = true;
Init.isMaster = true;
Init.protocol = kSaiBusI2SLeft;
Init.sampleBit = 16;
Init.sampleRate = 44100;
Init.chl = 0;
I2S_Init(&Init);
/* pinmux */
PORT_PinMuxConfig(HW_GPIOE, 6, kPinAlt4);
PORT_PinMuxConfig(HW_GPIOE, 7, kPinAlt4);
PORT_PinMuxConfig(HW_GPIOE, 12, kPinAlt4);
PORT_PinMuxConfig(HW_GPIOE, 11, kPinAlt4);
PORT_PinMuxConfig(HW_GPIOE, 10, kPinAlt4);
while(1)
{
I2S_SendData(0, 16, 0, (uint8_t*)music_44100_16_2, sizeof(music_44100_16_2));
printf("complete\r\n");
// DelayMs(500);
}
}
void MB85RC64_Init(uint32_t I2CMAP)
{
gInstance = I2C_QuickInit(BOARD_I2C_MAP, 100*1000);
}
