static void
dumpchannels(struct ath_hal *ah, int nc,
const struct ieee80211_channel *chans, int16_t *txpow)
{
int i;
for (i = 0; i < nc; i++) {
const struct ieee80211_channel *c = &chans[i];
int type;
if (showchannels)
printf("%s%3d", sep,
ath_hal_mhz2ieee(ah, c->ic_freq, c->ic_flags));
else
printf("%s%u", sep, c->ic_freq);
if (IEEE80211_IS_CHAN_HALF(c))
type = 'H';
else if (IEEE80211_IS_CHAN_QUARTER(c))
type = 'Q';
else if (IEEE80211_IS_CHAN_TURBO(c))
type = 'T';
else if (IEEE80211_IS_CHAN_HT(c))
type = 'N';
else if (IEEE80211_IS_CHAN_A(c))
type = 'A';
else if (IEEE80211_IS_CHAN_108G(c))
type = 'T';
else if (IEEE80211_IS_CHAN_G(c))
type = 'G';
else
type = 'B';
if (dopassive && IEEE80211_IS_CHAN_PASSIVE(c))
type = tolower(type);
if (isdfs && is4ms)
printf("%c%c%c %d.%d", type,
IEEE80211_IS_CHAN_DFS(c) ? '*' : ' ',
IEEE80211_IS_CHAN_4MS(c) ? '4' : ' ',
txpow[i]/2, (txpow[i]%2)*5);
else if (isdfs)
printf("%c%c %d.%d", type,
IEEE80211_IS_CHAN_DFS(c) ? '*' : ' ',
txpow[i]/2, (txpow[i]%2)*5);
else if (is4ms)
printf("%c%c %d.%d", type,
IEEE80211_IS_CHAN_4MS(c) ? '4' : ' ',
txpow[i]/2, (txpow[i]%2)*5);
else
printf("%c %d.%d", type, txpow[i]/2, (txpow[i]%2)*5);
if ((n++ % (showchannels ? 7 : 6)) == 0)
sep = "\n";
else
sep = " ";
}
}
/*
* Enable radar check
*/
void
ath_dfs_radar_enable(struct ath_softc *sc, struct ieee80211_channel *chan)
{
/* Check if the current channel is radar-enabled */
if (! IEEE80211_IS_CHAN_DFS(chan))
return;
}
/* Implement wmi_unified_vdev_start_cmd() here */
static int _ieee80211_resmgr_vap_start(ieee80211_resmgr_t resmgr,
ieee80211_vap_t vap,
struct ieee80211_channel *chan,
u_int16_t reqid,
u_int16_t max_start_time)
{
struct ieee80211com *ic = resmgr->ic;
struct ol_ath_softc_net80211 *scn = OL_ATH_SOFTC_NET80211(ic);
struct ol_ath_vap_net80211 *avn = OL_ATH_VAP_NET80211(vap);
u_int32_t freq;
bool disable_hw_ack= false;
printk("OL vap_start +\n");
freq = ieee80211_chan2freq(resmgr->ic, chan);
if (!freq) {
printk("ERROR : INVALID Freq \n");
return 0;
}
#if ATH_SUPPORT_DFS
if ( vap->iv_opmode == IEEE80211_M_HOSTAP &&
IEEE80211_IS_CHAN_DFS(chan)) {
disable_hw_ack = true;
}
#endif
/* BUG : Seen on AKronite, VDEV Start event response comes before setting
* av_ol_resmgr_wait to TRUE, this make VAP not coming up issue.
* Hence moving below assignment before sending VDEV_START_CMD_ID to target
*/
/* Interface is up, UMAC is waiting for
* target response
*/
avn->av_ol_resmgr_wait = TRUE;
spin_lock(&vap->init_lock);
if (wmi_unified_vdev_start_send(scn->wmi_handle, avn->av_if_id, chan, freq, disable_hw_ack)) {
printk("Unable to bring up the interface for ath_dev.\n");
spin_unlock(&vap->init_lock);
return -1;
}
/* The channel configured in target is not same always with the vap desired channel
due to 20/40 coexistence scenarios, so, channel is saved to configure on VDEV START RESP */
avn->av_ol_resmgr_chan = chan;
vap->init_in_progress = true;
spin_unlock(&vap->init_lock);
printk("OL vap_start -\n");
return EBUSY;
}
/*
* Enable radar check. Return 1 if the driver should
* enable radar PHY errors, or 0 if not.
*/
int
ath_dfs_radar_enable(struct ath_softc *sc, struct ieee80211_channel *chan)
{
#if 0
HAL_PHYERR_PARAM pe;
/* Check if the hardware supports radar reporting */
/* XXX TODO: migrate HAL_CAP_RADAR/HAL_CAP_AR to somewhere public! */
if (ath_hal_getcapability(sc->sc_ah,
HAL_CAP_PHYDIAG, 0, NULL) != HAL_OK)
return (0);
/* Check if the current channel is radar-enabled */
if (! IEEE80211_IS_CHAN_DFS(chan))
return (0);
/* Fetch the default parameters */
memset(&pe, '\0', sizeof(pe));
if (! ath_hal_getdfsdefaultthresh(sc->sc_ah, &pe))
return (0);
/* Enable radar PHY error reporting */
sc->sc_dodfs = 1;
/* Tell the hardware to enable radar reporting */
pe.pe_enabled = 1;
/* Flip on extension channel events only if doing HT40 */
if (IEEE80211_IS_CHAN_HT40(chan))
pe.pe_extchannel = 1;
else
pe.pe_extchannel = 0;
ath_hal_enabledfs(sc->sc_ah, &pe);
/*
* Disable strong signal fast diversity - needed for
* AR5212 and similar PHYs for reliable short pulse
* duration.
*/
(void) ath_hal_setcapability(sc->sc_ah, HAL_CAP_DIVERSITY, 2, 0, NULL);
return (1);
#else
return (0);
#endif
}
void
dfs_process_phyerr(struct ieee80211com *ic, void *buf, uint16_t datalen,
uint8_t r_rssi, uint8_t r_ext_rssi, uint32_t r_rs_tstamp,
uint64_t r_fulltsf, bool enable_log)
{
struct ath_dfs *dfs = (struct ath_dfs *)ic->ic_dfs;
struct dfs_ieee80211_channel *chan = ic->ic_curchan;
struct dfs_event *event;
struct dfs_phy_err e;
int empty;
if (dfs == NULL) {
CDF_TRACE(CDF_MODULE_ID_SAP, CDF_TRACE_LEVEL_ERROR,
"%s: sc_dfs is NULL\n", __func__);
return;
}
dfs->dfs_phyerr_count++;
dump_phyerr_contents(buf, datalen);
/*
* XXX The combined_rssi_ok support has been removed.
* This was only clear for Owl.
*
* XXX TODO: re-add this; it requires passing in the ctl/ext
* RSSI set from the RX status descriptor.
*
* XXX TODO TODO: this may be done for us from the legacy
* phy error path in ath_dev; please review that code.
*/
/*
* At this time we have a radar pulse that we need to examine and
* queue. But if dfs_process_radarevent already detected radar and set
* CHANNEL_INTERFERENCE flag then do not queue any more radar data.
* When we are in a new channel this flag will be clear and we will
* start queueing data for new channel. (EV74162)
*/
if (dfs->dfs_debug_mask & ATH_DEBUG_DFS_PHYERR_PKT)
dump_phyerr_contents(buf, datalen);
if (chan == NULL) {
CDF_TRACE(CDF_MODULE_ID_SAP, CDF_TRACE_LEVEL_ERROR,
"%s: chan is NULL\n", __func__);
return;
}
cdf_spin_lock_bh(&ic->chan_lock);
if (IEEE80211_IS_CHAN_RADAR(chan)) {
cdf_spin_unlock_bh(&ic->chan_lock);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1,
"%s: Radar already found in the channel, "
" do not queue radar data\n", __func__);
return;
}
cdf_spin_unlock_bh(&ic->chan_lock);
dfs->ath_dfs_stats.total_phy_errors++;
DFS_DPRINTK(dfs, ATH_DEBUG_DFS2,
"%s[%d] phyerr %d len %d\n",
__func__, __LINE__,
dfs->ath_dfs_stats.total_phy_errors, datalen);
/*
* hardware stores this as 8 bit signed value.
* we will cap it at 0 if it is a negative number
*/
if (r_rssi & 0x80)
r_rssi = 0;
if (r_ext_rssi & 0x80)
r_ext_rssi = 0;
OS_MEMSET(&e, 0, sizeof(e));
/*
* This is a bit evil - instead of just passing in
* the chip version, the existing code uses a set
* of HAL capability bits to determine what is
* possible.
*
* The way I'm decoding it is thus:
*
* + DFS enhancement? Merlin or later
* + DFS extension channel? Sowl or later. (Howl?)
* + otherwise, Owl (and legacy.)
*/
if (dfs->dfs_caps.ath_chip_is_bb_tlv) {
if (dfs_process_phyerr_bb_tlv(dfs, buf, datalen, r_rssi,
r_ext_rssi, r_rs_tstamp,
r_fulltsf, &e,
enable_log) == 0) {
dfs->dfs_phyerr_reject_count++;
return;
} else {
if (dfs->dfs_phyerr_freq_min > e.freq)
dfs->dfs_phyerr_freq_min = e.freq;
if (dfs->dfs_phyerr_freq_max < e.freq)
dfs->dfs_phyerr_freq_max = e.freq;
}
} else if (dfs->dfs_caps.ath_dfs_use_enhancement) {
if (dfs_process_phyerr_merlin(dfs, buf, datalen, r_rssi,
r_ext_rssi, r_rs_tstamp,
r_fulltsf, &e) == 0) {
return;
}
} else if (dfs->dfs_caps.ath_dfs_ext_chan_ok) {
if (dfs_process_phyerr_sowl(dfs, buf, datalen, r_rssi,
r_ext_rssi, r_rs_tstamp, r_fulltsf,
&e) == 0) {
return;
}
} else {
if (dfs_process_phyerr_owl(dfs, buf, datalen, r_rssi,
r_ext_rssi, r_rs_tstamp, r_fulltsf,
&e) == 0) {
return;
}
}
CDF_TRACE(CDF_MODULE_ID_SAP, CDF_TRACE_LEVEL_INFO,
"\n %s: Frequency at which the phyerror was injected = %d",
__func__, e.freq);
/*
* If the hardware supports radar reporting on the extension channel
* it will supply FFT data for longer radar pulses.
*
* TLV chips don't go through this software check - the hardware
* check should be enough. If we want to do software checking
* later on then someone will have to craft an FFT parser
* suitable for the TLV FFT data format.
*/
if ((!dfs->dfs_caps.ath_chip_is_bb_tlv) &&
dfs->dfs_caps.ath_dfs_ext_chan_ok) {
/*
* HW has a known issue with chirping pulses injected at or
* around DC in 40MHz mode. Such pulses are reported with
* much lower durations and SW then discards them because
* they do not fit the minimum bin5 pulse duration.
*
* To work around this issue, if a pulse is within a 10us
* range of the bin5 min duration, check if the pulse is
* chirping. If the pulse is chirping, bump up the duration
* to the minimum bin5 duration.
*
* This makes sure that a valid chirping pulse will not be
* discarded because of incorrect low duration.
*
* TBD - Is it possible to calculate the 'real' duration of
* the pulse using the slope of the FFT data?
*
* TBD - Use FFT data to differentiate between radar pulses
* and false PHY errors.
* This will let us reduce the number of false alarms seen.
*
* BIN 5 chirping pulses are only for FCC or Japan MMK4 domain
*/
if (((dfs->dfsdomain == DFS_FCC_DOMAIN) ||
(dfs->dfsdomain == DFS_MKK4_DOMAIN)) &&
(e.dur >= MAYBE_BIN5_DUR) && (e.dur < MAX_BIN5_DUR)) {
int add_dur;
int slope = 0, dc_found = 0;
/*
* Set the event chirping flags; as we're doing
* an actual chirp check.
*/
e.do_check_chirp = 1;
e.is_hw_chirp = 0;
e.is_sw_chirp = 0;
/*
* dfs_check_chirping() expects is_pri and is_ext
* to be '1' for true and '0' for false for now,
* as the function itself uses these values in
* constructing things rather than testing them
* for 'true' or 'false'.
*/
add_dur = dfs_check_chirping(dfs, buf, datalen,
(e.is_pri ? 1 : 0),
(e.is_ext ? 1 : 0),
&slope, &dc_found);
if (add_dur) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS_PHYERR,
"old dur %d slope =%d\n", e.dur,
slope);
e.is_sw_chirp = 1;
/* bump up to a random bin5 pulse duration */
if (e.dur < MIN_BIN5_DUR) {
e.dur = dfs_get_random_bin5_dur(dfs,
e.fulltsf);
}
DFS_DPRINTK(dfs, ATH_DEBUG_DFS_PHYERR,
"new dur %d\n", e.dur);
} else {
/* set the duration so that it is rejected */
e.is_sw_chirp = 0;
e.dur = MAX_BIN5_DUR + 100;
DFS_DPRINTK(dfs, ATH_DEBUG_DFS_PHYERR,
"is_chirping = %d dur=%d\n",
add_dur, e.dur);
}
} else {
/*
* We have a pulse that is either bigger than
* MAX_BIN5_DUR or * less than MAYBE_BIN5_DUR
*/
if ((dfs->dfsdomain == DFS_FCC_DOMAIN) ||
(dfs->dfsdomain == DFS_MKK4_DOMAIN)) {
/*
* XXX Would this result in very large pulses
* wrapping around to become short pulses?
*/
if (e.dur >= MAX_BIN5_DUR) {
/*
* set the duration so that it is
* rejected
*/
e.dur = MAX_BIN5_DUR + 50;
}
}
}
}
/*
* Add the parsed, checked and filtered entry to the radar pulse
* event list. This is then checked by dfs_radar_processevent().
*
* XXX TODO: some filtering is still done below this point - fix
* XXX this!
*/
ATH_DFSEVENTQ_LOCK(dfs);
empty = STAILQ_EMPTY(&(dfs->dfs_eventq));
ATH_DFSEVENTQ_UNLOCK(dfs);
if (empty) {
return;
}
/*
* If the channel is a turbo G channel, then the event is
* for the adaptive radio (AR) pattern matching rather than
* radar detection.
*/
cdf_spin_lock_bh(&ic->chan_lock);
if ((chan->ic_flags & CHANNEL_108G) == CHANNEL_108G) {
cdf_spin_unlock_bh(&ic->chan_lock);
if (!(dfs->dfs_proc_phyerr & DFS_AR_EN)) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS2,
"%s: DFS_AR_EN not enabled\n", __func__);
return;
}
ATH_DFSEVENTQ_LOCK(dfs);
event = STAILQ_FIRST(&(dfs->dfs_eventq));
if (event == NULL) {
ATH_DFSEVENTQ_UNLOCK(dfs);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS,
"%s: no more events space left\n",
__func__);
return;
}
STAILQ_REMOVE_HEAD(&(dfs->dfs_eventq), re_list);
ATH_DFSEVENTQ_UNLOCK(dfs);
event->re_rssi = e.rssi;
event->re_dur = e.dur;
event->re_full_ts = e.fulltsf;
event->re_ts = (e.rs_tstamp) & DFS_TSMASK;
event->re_chanindex = dfs->dfs_curchan_radindex;
event->re_flags = 0;
event->sidx = e.sidx;
/*
* Handle chirp flags.
*/
if (e.do_check_chirp) {
event->re_flags |= DFS_EVENT_CHECKCHIRP;
if (e.is_hw_chirp)
event->re_flags |= DFS_EVENT_HW_CHIRP;
if (e.is_sw_chirp)
event->re_flags |= DFS_EVENT_SW_CHIRP;
}
ATH_ARQ_LOCK(dfs);
STAILQ_INSERT_TAIL(&(dfs->dfs_arq), event, re_list);
ATH_ARQ_UNLOCK(dfs);
} else {
if (IEEE80211_IS_CHAN_DFS(chan)) {
cdf_spin_unlock_bh(&ic->chan_lock);
if (!(dfs->dfs_proc_phyerr & DFS_RADAR_EN)) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS3,
"%s: DFS_RADAR_EN not enabled\n",
__func__);
return;
}
/*
* rssi is not accurate for short pulses, so do
* not filter based on that for short duration pulses
*
* XXX do this filtering above?
*/
if (dfs->dfs_caps.ath_dfs_ext_chan_ok) {
if ((e.rssi < dfs->dfs_rinfo.rn_minrssithresh &&
(e.dur > 4)) ||
e.dur > (dfs->dfs_rinfo.rn_maxpulsedur)) {
dfs->ath_dfs_stats.rssi_discards++;
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1,
"Extension channel pulse is "
"discarded: dur=%d, "
"maxpulsedur=%d, rssi=%d, "
"minrssi=%d\n",
e.dur,
dfs->dfs_rinfo.
rn_maxpulsedur, e.rssi,
dfs->dfs_rinfo.
rn_minrssithresh);
return;
}
} else {
if (e.rssi < dfs->dfs_rinfo.rn_minrssithresh ||
e.dur > dfs->dfs_rinfo.rn_maxpulsedur) {
/* XXX TODO add a debug statement? */
dfs->ath_dfs_stats.rssi_discards++;
return;
}
}
/*
* Add the event to the list, if there's space.
*/
ATH_DFSEVENTQ_LOCK(dfs);
event = STAILQ_FIRST(&(dfs->dfs_eventq));
if (event == NULL) {
ATH_DFSEVENTQ_UNLOCK(dfs);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS,
"%s: no more events space left\n",
__func__);
return;
}
STAILQ_REMOVE_HEAD(&(dfs->dfs_eventq), re_list);
ATH_DFSEVENTQ_UNLOCK(dfs);
dfs->dfs_phyerr_queued_count++;
dfs->dfs_phyerr_w53_counter++;
event->re_dur = e.dur;
event->re_full_ts = e.fulltsf;
event->re_ts = (e.rs_tstamp) & DFS_TSMASK;
event->re_rssi = e.rssi;
event->sidx = e.sidx;
/*
* Handle chirp flags.
*/
if (e.do_check_chirp) {
event->re_flags |= DFS_EVENT_CHECKCHIRP;
if (e.is_hw_chirp)
event->re_flags |= DFS_EVENT_HW_CHIRP;
if (e.is_sw_chirp)
event->re_flags |= DFS_EVENT_SW_CHIRP;
}
/*
* Correctly set which channel is being reported on
*/
if (e.is_pri) {
event->re_chanindex = dfs->dfs_curchan_radindex;
} else {
if (dfs->dfs_extchan_radindex == -1) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS_PHYERR,
"%s - phyerr on ext channel\n",
__func__);
}
event->re_chanindex = dfs->dfs_extchan_radindex;
DFS_DPRINTK(dfs, ATH_DEBUG_DFS_PHYERR,
"%s New extension channel event is added "
"to queue\n", __func__);
}
ATH_DFSQ_LOCK(dfs);
STAILQ_INSERT_TAIL(&(dfs->dfs_radarq), event, re_list);
ATH_DFSQ_UNLOCK(dfs);
} else {
cdf_spin_unlock_bh(&ic->chan_lock);
}
}
/*
* Schedule the radar/AR task as appropriate.
*
* XXX isn't a lock needed for ath_radar_tasksched?
*/
/*
* Commenting out the dfs_process_ar_event() since the function is never
* called at run time as dfs_arq will be empty and the function
* dfs_process_ar_event is obsolete and function definition is removed
* as part of dfs_ar.c file
*
* if (!STAILQ_EMPTY(&dfs->dfs_arq))
* // XXX shouldn't this be a task/timer too?
* dfs_process_ar_event(dfs, ic->ic_curchan);
*/
if (!STAILQ_EMPTY(&dfs->dfs_radarq) && !dfs->ath_radar_tasksched) {
dfs->ath_radar_tasksched = 1;
OS_SET_TIMER(&dfs->ath_dfs_task_timer, 0);
}
#undef EXT_CH_RADAR_FOUND
#undef PRI_CH_RADAR_FOUND
#undef EXT_CH_RADAR_EARLY_FOUND
}
/*
* Places the device in and out of reset and then places sane
* values in the registers based on EEPROM config, initialization
* vectors (as determined by the mode), and station configuration
*
* bChannelChange is used to preserve DMA/PCU registers across
* a HW Reset during channel change.
*/
HAL_BOOL
ar5312Reset(struct ath_hal *ah, HAL_OPMODE opmode,
struct ieee80211_channel *chan,
HAL_BOOL bChannelChange,
HAL_RESET_TYPE resetType,
HAL_STATUS *status)
{
#define N(a) (sizeof (a) / sizeof (a[0]))
#define FAIL(_code) do { ecode = _code; goto bad; } while (0)
struct ath_hal_5212 *ahp = AH5212(ah);
HAL_CHANNEL_INTERNAL *ichan;
const HAL_EEPROM *ee;
uint32_t saveFrameSeqCount, saveDefAntenna;
uint32_t macStaId1, synthDelay, txFrm2TxDStart;
uint16_t rfXpdGain[MAX_NUM_PDGAINS_PER_CHANNEL];
int16_t cckOfdmPwrDelta = 0;
u_int modesIndex, freqIndex;
HAL_STATUS ecode;
int i, regWrites = 0;
uint32_t testReg;
uint32_t saveLedState = 0;
HALASSERT(ah->ah_magic == AR5212_MAGIC);
ee = AH_PRIVATE(ah)->ah_eeprom;
OS_MARK(ah, AH_MARK_RESET, bChannelChange);
/*
* Map public channel to private.
*/
ichan = ath_hal_checkchannel(ah, chan);
if (ichan == AH_NULL) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: invalid channel %u/0x%x; no mapping\n",
__func__, chan->ic_freq, chan->ic_flags);
FAIL(HAL_EINVAL);
}
switch (opmode) {
case HAL_M_STA:
case HAL_M_IBSS:
case HAL_M_HOSTAP:
case HAL_M_MONITOR:
break;
default:
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: invalid operating mode %u\n",
__func__, opmode);
FAIL(HAL_EINVAL);
break;
}
HALASSERT(ahp->ah_eeversion >= AR_EEPROM_VER3);
/* Preserve certain DMA hardware registers on a channel change */
if (bChannelChange) {
/*
* On Venice, the TSF is almost preserved across a reset;
* it requires the doubling writes to the RESET_TSF
* bit in the AR_BEACON register; it also has the quirk
* of the TSF going back in time on the station (station
* latches onto the last beacon's tsf during a reset 50%
* of the times); the latter is not a problem for adhoc
* stations since as long as the TSF is behind, it will
* get resynchronized on receiving the next beacon; the
* TSF going backwards in time could be a problem for the
* sleep operation (supported on infrastructure stations
* only) - the best and most general fix for this situation
* is to resynchronize the various sleep/beacon timers on
* the receipt of the next beacon i.e. when the TSF itself
* gets resynchronized to the AP's TSF - power save is
* needed to be temporarily disabled until that time
*
* Need to save the sequence number to restore it after
* the reset!
*/
saveFrameSeqCount = OS_REG_READ(ah, AR_D_SEQNUM);
} else
saveFrameSeqCount = 0; /* NB: silence compiler */
/* If the channel change is across the same mode - perform a fast channel change */
if ((IS_2413(ah) || IS_5413(ah))) {
/*
* Channel change can only be used when:
* -channel change requested - so it's not the initial reset.
* -it's not a change to the current channel - often called when switching modes
* on a channel
* -the modes of the previous and requested channel are the same - some ugly code for XR
*/
if (bChannelChange &&
AH_PRIVATE(ah)->ah_curchan != AH_NULL &&
(chan->ic_freq != AH_PRIVATE(ah)->ah_curchan->ic_freq) &&
((chan->ic_flags & IEEE80211_CHAN_ALLTURBO) ==
(AH_PRIVATE(ah)->ah_curchan->ic_flags & IEEE80211_CHAN_ALLTURBO))) {
if (ar5212ChannelChange(ah, chan))
/* If ChannelChange completed - skip the rest of reset */
return AH_TRUE;
}
}
/*
* Preserve the antenna on a channel change
*/
saveDefAntenna = OS_REG_READ(ah, AR_DEF_ANTENNA);
if (saveDefAntenna == 0) /* XXX magic constants */
saveDefAntenna = 1;
/* Save hardware flag before chip reset clears the register */
macStaId1 = OS_REG_READ(ah, AR_STA_ID1) &
(AR_STA_ID1_BASE_RATE_11B | AR_STA_ID1_USE_DEFANT);
/* Save led state from pci config register */
if (!IS_5315(ah))
saveLedState = OS_REG_READ(ah, AR5312_PCICFG) &
(AR_PCICFG_LEDCTL | AR_PCICFG_LEDMODE | AR_PCICFG_LEDBLINK |
AR_PCICFG_LEDSLOW);
ar5312RestoreClock(ah, opmode); /* move to refclk operation */
/*
* Adjust gain parameters before reset if
* there's an outstanding gain updated.
*/
(void) ar5212GetRfgain(ah);
if (!ar5312ChipReset(ah, chan)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: chip reset failed\n", __func__);
FAIL(HAL_EIO);
}
/* Setup the indices for the next set of register array writes */
if (IEEE80211_IS_CHAN_2GHZ(chan)) {
freqIndex = 2;
modesIndex = IEEE80211_IS_CHAN_108G(chan) ? 5 :
IEEE80211_IS_CHAN_G(chan) ? 4 : 3;
} else {
freqIndex = 1;
modesIndex = IEEE80211_IS_CHAN_ST(chan) ? 2 : 1;
}
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
regWrites = ath_hal_ini_write(ah, &ahp->ah_ini_modes, modesIndex, 0);
regWrites = write_common(ah, &ahp->ah_ini_common, bChannelChange,
regWrites);
ahp->ah_rfHal->writeRegs(ah, modesIndex, freqIndex, regWrites);
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
if (IEEE80211_IS_CHAN_HALF(chan) || IEEE80211_IS_CHAN_QUARTER(chan))
ar5212SetIFSTiming(ah, chan);
/* Overwrite INI values for revised chipsets */
if (AH_PRIVATE(ah)->ah_phyRev >= AR_PHY_CHIP_ID_REV_2) {
/* ADC_CTL */
OS_REG_WRITE(ah, AR_PHY_ADC_CTL,
SM(2, AR_PHY_ADC_CTL_OFF_INBUFGAIN) |
SM(2, AR_PHY_ADC_CTL_ON_INBUFGAIN) |
AR_PHY_ADC_CTL_OFF_PWDDAC |
AR_PHY_ADC_CTL_OFF_PWDADC);
/* TX_PWR_ADJ */
if (chan->channel == 2484) {
cckOfdmPwrDelta = SCALE_OC_DELTA(ee->ee_cckOfdmPwrDelta - ee->ee_scaledCh14FilterCckDelta);
} else {
cckOfdmPwrDelta = SCALE_OC_DELTA(ee->ee_cckOfdmPwrDelta);
}
if (IEEE80211_IS_CHAN_G(chan)) {
OS_REG_WRITE(ah, AR_PHY_TXPWRADJ,
SM((ee->ee_cckOfdmPwrDelta*-1), AR_PHY_TXPWRADJ_CCK_GAIN_DELTA) |
SM((cckOfdmPwrDelta*-1), AR_PHY_TXPWRADJ_CCK_PCDAC_INDEX));
} else {
OS_REG_WRITE(ah, AR_PHY_TXPWRADJ, 0);
}
/* Add barker RSSI thresh enable as disabled */
OS_REG_CLR_BIT(ah, AR_PHY_DAG_CTRLCCK,
AR_PHY_DAG_CTRLCCK_EN_RSSI_THR);
OS_REG_RMW_FIELD(ah, AR_PHY_DAG_CTRLCCK,
AR_PHY_DAG_CTRLCCK_RSSI_THR, 2);
/* Set the mute mask to the correct default */
OS_REG_WRITE(ah, AR_SEQ_MASK, 0x0000000F);
}
if (AH_PRIVATE(ah)->ah_phyRev >= AR_PHY_CHIP_ID_REV_3) {
/* Clear reg to alllow RX_CLEAR line debug */
OS_REG_WRITE(ah, AR_PHY_BLUETOOTH, 0);
}
if (AH_PRIVATE(ah)->ah_phyRev >= AR_PHY_CHIP_ID_REV_4) {
#ifdef notyet
/* Enable burst prefetch for the data queues */
OS_REG_RMW_FIELD(ah, AR_D_FPCTL, ... );
/* Enable double-buffering */
OS_REG_CLR_BIT(ah, AR_TXCFG, AR_TXCFG_DBL_BUF_DIS);
#endif
}
if (IS_5312_2_X(ah)) {
/* ADC_CTRL */
OS_REG_WRITE(ah, AR_PHY_SIGMA_DELTA,
SM(2, AR_PHY_SIGMA_DELTA_ADC_SEL) |
SM(4, AR_PHY_SIGMA_DELTA_FILT2) |
SM(0x16, AR_PHY_SIGMA_DELTA_FILT1) |
SM(0, AR_PHY_SIGMA_DELTA_ADC_CLIP));
if (IEEE80211_IS_CHAN_2GHZ(chan))
OS_REG_RMW_FIELD(ah, AR_PHY_RXGAIN, AR_PHY_RXGAIN_TXRX_RF_MAX, 0x0F);
/* CCK Short parameter adjustment in 11B mode */
if (IEEE80211_IS_CHAN_B(chan))
OS_REG_RMW_FIELD(ah, AR_PHY_CCK_RXCTRL4, AR_PHY_CCK_RXCTRL4_FREQ_EST_SHORT, 12);
/* Set ADC/DAC select values */
OS_REG_WRITE(ah, AR_PHY_SLEEP_SCAL, 0x04);
/* Increase 11A AGC Settling */
if (IEEE80211_IS_CHAN_A(chan))
OS_REG_RMW_FIELD(ah, AR_PHY_SETTLING, AR_PHY_SETTLING_AGC, 32);
} else {
/* Set ADC/DAC select values */
OS_REG_WRITE(ah, AR_PHY_SLEEP_SCAL, 0x0e);
}
/* Setup the transmit power values. */
if (!ar5212SetTransmitPower(ah, chan, rfXpdGain)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: error init'ing transmit power\n", __func__);
FAIL(HAL_EIO);
}
/* Write the analog registers */
if (!ahp->ah_rfHal->setRfRegs(ah, chan, modesIndex, rfXpdGain)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: ar5212SetRfRegs failed\n",
__func__);
FAIL(HAL_EIO);
}
/* Write delta slope for OFDM enabled modes (A, G, Turbo) */
if (IEEE80211_IS_CHAN_OFDM(chan)) {
if (IS_5413(ah) ||
AH_PRIVATE(ah)->ah_eeversion >= AR_EEPROM_VER5_3)
ar5212SetSpurMitigation(ah, chan);
ar5212SetDeltaSlope(ah, chan);
}
/* Setup board specific options for EEPROM version 3 */
if (!ar5212SetBoardValues(ah, chan)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: error setting board options\n", __func__);
FAIL(HAL_EIO);
}
/* Restore certain DMA hardware registers on a channel change */
if (bChannelChange)
OS_REG_WRITE(ah, AR_D_SEQNUM, saveFrameSeqCount);
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
OS_REG_WRITE(ah, AR_STA_ID0, LE_READ_4(ahp->ah_macaddr));
OS_REG_WRITE(ah, AR_STA_ID1, LE_READ_2(ahp->ah_macaddr + 4)
| macStaId1
| AR_STA_ID1_RTS_USE_DEF
| ahp->ah_staId1Defaults
);
ar5212SetOperatingMode(ah, opmode);
/* Set Venice BSSID mask according to current state */
OS_REG_WRITE(ah, AR_BSSMSKL, LE_READ_4(ahp->ah_bssidmask));
OS_REG_WRITE(ah, AR_BSSMSKU, LE_READ_2(ahp->ah_bssidmask + 4));
/* Restore previous led state */
if (!IS_5315(ah))
OS_REG_WRITE(ah, AR5312_PCICFG, OS_REG_READ(ah, AR_PCICFG) | saveLedState);
/* Restore previous antenna */
OS_REG_WRITE(ah, AR_DEF_ANTENNA, saveDefAntenna);
/* then our BSSID */
OS_REG_WRITE(ah, AR_BSS_ID0, LE_READ_4(ahp->ah_bssid));
OS_REG_WRITE(ah, AR_BSS_ID1, LE_READ_2(ahp->ah_bssid + 4));
/* Restore bmiss rssi & count thresholds */
OS_REG_WRITE(ah, AR_RSSI_THR, ahp->ah_rssiThr);
OS_REG_WRITE(ah, AR_ISR, ~0); /* cleared on write */
if (!ar5212SetChannel(ah, chan))
FAIL(HAL_EIO);
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
ar5212SetCoverageClass(ah, AH_PRIVATE(ah)->ah_coverageClass, 1);
ar5212SetRateDurationTable(ah, chan);
/* Set Tx frame start to tx data start delay */
if (IS_RAD5112_ANY(ah) &&
(IEEE80211_IS_CHAN_HALF(chan) || IEEE80211_IS_CHAN_QUARTER(chan))) {
txFrm2TxDStart =
IEEE80211_IS_CHAN_HALF(chan) ?
TX_FRAME_D_START_HALF_RATE:
TX_FRAME_D_START_QUARTER_RATE;
OS_REG_RMW_FIELD(ah, AR_PHY_TX_CTL,
AR_PHY_TX_FRAME_TO_TX_DATA_START, txFrm2TxDStart);
}
/*
* Setup fast diversity.
* Fast diversity can be enabled or disabled via regadd.txt.
* Default is enabled.
* For reference,
* Disable: reg val
* 0x00009860 0x00009d18 (if 11a / 11g, else no change)
* 0x00009970 0x192bb514
* 0x0000a208 0xd03e4648
*
* Enable: 0x00009860 0x00009d10 (if 11a / 11g, else no change)
* 0x00009970 0x192fb514
* 0x0000a208 0xd03e6788
*/
/* XXX Setup pre PHY ENABLE EAR additions */
/* flush SCAL reg */
if (IS_5312_2_X(ah)) {
(void) OS_REG_READ(ah, AR_PHY_SLEEP_SCAL);
}
/*
* Wait for the frequency synth to settle (synth goes on
* via AR_PHY_ACTIVE_EN). Read the phy active delay register.
* Value is in 100ns increments.
*/
synthDelay = OS_REG_READ(ah, AR_PHY_RX_DELAY) & AR_PHY_RX_DELAY_DELAY;
if (IEEE80211_IS_CHAN_B(chan)) {
synthDelay = (4 * synthDelay) / 22;
} else {
synthDelay /= 10;
}
/* Activate the PHY (includes baseband activate and synthesizer on) */
OS_REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN);
/*
* There is an issue if the AP starts the calibration before
* the base band timeout completes. This could result in the
* rx_clear false triggering. As a workaround we add delay an
* extra BASE_ACTIVATE_DELAY usecs to ensure this condition
* does not happen.
*/
if (IEEE80211_IS_CHAN_HALF(chan)) {
OS_DELAY((synthDelay << 1) + BASE_ACTIVATE_DELAY);
} else if (IEEE80211_IS_CHAN_QUARTER(chan)) {
OS_DELAY((synthDelay << 2) + BASE_ACTIVATE_DELAY);
} else {
OS_DELAY(synthDelay + BASE_ACTIVATE_DELAY);
}
/*
* The udelay method is not reliable with notebooks.
* Need to check to see if the baseband is ready
*/
testReg = OS_REG_READ(ah, AR_PHY_TESTCTRL);
/* Selects the Tx hold */
OS_REG_WRITE(ah, AR_PHY_TESTCTRL, AR_PHY_TESTCTRL_TXHOLD);
i = 0;
while ((i++ < 20) &&
(OS_REG_READ(ah, 0x9c24) & 0x10)) /* test if baseband not ready */ OS_DELAY(200);
OS_REG_WRITE(ah, AR_PHY_TESTCTRL, testReg);
/* Calibrate the AGC and start a NF calculation */
OS_REG_WRITE(ah, AR_PHY_AGC_CONTROL,
OS_REG_READ(ah, AR_PHY_AGC_CONTROL)
| AR_PHY_AGC_CONTROL_CAL
| AR_PHY_AGC_CONTROL_NF);
if (!IEEE80211_IS_CHAN_B(chan) && ahp->ah_bIQCalibration != IQ_CAL_DONE) {
/* Start IQ calibration w/ 2^(INIT_IQCAL_LOG_COUNT_MAX+1) samples */
OS_REG_RMW_FIELD(ah, AR_PHY_TIMING_CTRL4,
AR_PHY_TIMING_CTRL4_IQCAL_LOG_COUNT_MAX,
INIT_IQCAL_LOG_COUNT_MAX);
OS_REG_SET_BIT(ah, AR_PHY_TIMING_CTRL4,
AR_PHY_TIMING_CTRL4_DO_IQCAL);
ahp->ah_bIQCalibration = IQ_CAL_RUNNING;
} else
ahp->ah_bIQCalibration = IQ_CAL_INACTIVE;
/* Setup compression registers */
ar5212SetCompRegs(ah);
/* Set 1:1 QCU to DCU mapping for all queues */
for (i = 0; i < AR_NUM_DCU; i++)
OS_REG_WRITE(ah, AR_DQCUMASK(i), 1 << i);
ahp->ah_intrTxqs = 0;
for (i = 0; i < AH_PRIVATE(ah)->ah_caps.halTotalQueues; i++)
ar5212ResetTxQueue(ah, i);
/*
* Setup interrupt handling. Note that ar5212ResetTxQueue
* manipulates the secondary IMR's as queues are enabled
* and disabled. This is done with RMW ops to insure the
* settings we make here are preserved.
*/
ahp->ah_maskReg = AR_IMR_TXOK | AR_IMR_TXERR | AR_IMR_TXURN
| AR_IMR_RXOK | AR_IMR_RXERR | AR_IMR_RXORN
| AR_IMR_HIUERR
;
if (opmode == HAL_M_HOSTAP)
ahp->ah_maskReg |= AR_IMR_MIB;
OS_REG_WRITE(ah, AR_IMR, ahp->ah_maskReg);
/* Enable bus errors that are OR'd to set the HIUERR bit */
OS_REG_WRITE(ah, AR_IMR_S2,
OS_REG_READ(ah, AR_IMR_S2)
| AR_IMR_S2_MCABT | AR_IMR_S2_SSERR | AR_IMR_S2_DPERR);
if (AH_PRIVATE(ah)->ah_rfkillEnabled)
ar5212EnableRfKill(ah);
if (!ath_hal_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: offset calibration failed to complete in 1ms;"
" noisy environment?\n", __func__);
}
/*
* Set clocks back to 32kHz if they had been using refClk, then
* use an external 32kHz crystal when sleeping, if one exists.
*/
ar5312SetupClock(ah, opmode);
/*
* Writing to AR_BEACON will start timers. Hence it should
* be the last register to be written. Do not reset tsf, do
* not enable beacons at this point, but preserve other values
* like beaconInterval.
*/
OS_REG_WRITE(ah, AR_BEACON,
(OS_REG_READ(ah, AR_BEACON) &~ (AR_BEACON_EN | AR_BEACON_RESET_TSF)));
/* XXX Setup post reset EAR additions */
/* QoS support */
if (AH_PRIVATE(ah)->ah_macVersion > AR_SREV_VERSION_VENICE ||
(AH_PRIVATE(ah)->ah_macVersion == AR_SREV_VERSION_VENICE &&
AH_PRIVATE(ah)->ah_macRev >= AR_SREV_GRIFFIN_LITE)) {
OS_REG_WRITE(ah, AR_QOS_CONTROL, 0x100aa); /* XXX magic */
OS_REG_WRITE(ah, AR_QOS_SELECT, 0x3210); /* XXX magic */
}
/* Turn on NOACK Support for QoS packets */
OS_REG_WRITE(ah, AR_NOACK,
SM(2, AR_NOACK_2BIT_VALUE) |
SM(5, AR_NOACK_BIT_OFFSET) |
SM(0, AR_NOACK_BYTE_OFFSET));
/* Restore user-specified settings */
if (ahp->ah_miscMode != 0)
OS_REG_WRITE(ah, AR_MISC_MODE, ahp->ah_miscMode);
if (ahp->ah_slottime != (u_int) -1)
ar5212SetSlotTime(ah, ahp->ah_slottime);
if (ahp->ah_acktimeout != (u_int) -1)
ar5212SetAckTimeout(ah, ahp->ah_acktimeout);
if (ahp->ah_ctstimeout != (u_int) -1)
ar5212SetCTSTimeout(ah, ahp->ah_ctstimeout);
if (ahp->ah_sifstime != (u_int) -1)
ar5212SetSifsTime(ah, ahp->ah_sifstime);
if (AH_PRIVATE(ah)->ah_diagreg != 0)
OS_REG_WRITE(ah, AR_DIAG_SW, AH_PRIVATE(ah)->ah_diagreg);
AH_PRIVATE(ah)->ah_opmode = opmode; /* record operating mode */
if (bChannelChange && !IEEE80211_IS_CHAN_DFS(chan))
chan->ic_state &= ~IEEE80211_CHANSTATE_CWINT;
HALDEBUG(ah, HAL_DEBUG_RESET, "%s: done\n", __func__);
OS_MARK(ah, AH_MARK_RESET_DONE, 0);
return AH_TRUE;
bad:
OS_MARK(ah, AH_MARK_RESET_DONE, ecode);
if (status != AH_NULL)
*status = ecode;
return AH_FALSE;
#undef FAIL
#undef N
}
/*
* Process a radar event.
*
* If a radar event is found, return 1. Otherwise, return 0.
*
* There is currently no way to specify that a radar event has occured on
* a specific channel, so the current methodology is to mark both the pri
* and ext channels as being unavailable. This should be fixed for 802.11ac
* or we'll quickly run out of valid channels to use.
*/
int
dfs_process_radarevent(struct ath_dfs *dfs, struct ieee80211_channel *chan)
{
struct dfs_event re,*event;
struct dfs_state *rs=NULL;
struct dfs_filtertype *ft;
struct dfs_filter *rf;
int found, retval = 0, p, empty;
int events_processed = 0;
u_int32_t tabledepth, index;
u_int64_t deltafull_ts = 0, this_ts, deltaT;
struct ieee80211_channel *thischan;
struct dfs_pulseline *pl;
static u_int32_t test_ts = 0;
static u_int32_t diff_ts = 0;
int ext_chan_event_flag = 0;
int i;
if (dfs == NULL) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "%s: sc_sfs is NULL\n",
__func__);
return 0;
}
pl = dfs->pulses;
if ( !(IEEE80211_IS_CHAN_DFS(dfs->ic->ic_curchan))) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS2, "%s: radar event on non-DFS chan\n",
__func__);
dfs_reset_radarq(dfs);
dfs_reset_alldelaylines(dfs);
return 0;
}
#ifndef ATH_DFS_RADAR_DETECTION_ONLY
/* TEST : Simulate radar bang, make sure we add the channel to NOL (bug 29968) */
if (dfs->dfs_bangradar) {
/* bangradar will always simulate radar found on the primary channel */
rs = &dfs->dfs_radar[dfs->dfs_curchan_radindex];
dfs->dfs_bangradar = 0; /* reset */
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "%s: bangradar\n", __func__);
retval = 1;
goto dfsfound;
}
#endif
/*
The HW may miss some pulses especially with high channel loading.
This is true for Japan W53 where channel loaoding is 50%. Also
for ETSI where channel loading is 30% this can be an issue too.
To take care of missing pulses, we introduce pri_margin multiplie.
This is normally 2 but can be higher for W53.
*/
if ((dfs->dfsdomain == DFS_MKK4_DOMAIN) &&
(dfs->dfs_caps.ath_chip_is_bb_tlv) &&
(chan->ic_freq < FREQ_5500_MHZ)) {
dfs->dfs_pri_multiplier = DFS_W53_DEFAULT_PRI_MULTIPLIER;
/* do not process W53 pulses unless we have a minimum number of them */
if (dfs->dfs_phyerr_w53_counter >= 5) {
/*
for chips that support frequency information, we can
relax PRI restriction if the frequency
spread is narrow.
*/
if ((dfs->dfs_phyerr_freq_max - dfs->dfs_phyerr_freq_min) < DFS_MAX_FREQ_SPREAD) {
dfs->dfs_pri_multiplier = DFS_LARGE_PRI_MULTIPLIER;
}
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1, "%s: w53_counter=%d, freq_max=%d, freq_min=%d, pri_multiplier=%d\n",
__func__,
dfs->dfs_phyerr_w53_counter,
dfs->dfs_phyerr_freq_max,
dfs->dfs_phyerr_freq_min,
dfs->dfs_pri_multiplier);
dfs->dfs_phyerr_freq_min = 0x7fffffff;
dfs->dfs_phyerr_freq_max = 0;
} else {
return 0;
}
}
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1, "%s: pri_multiplier=%d\n", __func__, dfs->dfs_pri_multiplier);
ATH_DFSQ_LOCK(dfs);
empty = STAILQ_EMPTY(&(dfs->dfs_radarq));
ATH_DFSQ_UNLOCK(dfs);
while ((!empty) && (!retval) && (events_processed < MAX_EVENTS)) {
ATH_DFSQ_LOCK(dfs);
event = STAILQ_FIRST(&(dfs->dfs_radarq));
if (event != NULL)
STAILQ_REMOVE_HEAD(&(dfs->dfs_radarq), re_list);
ATH_DFSQ_UNLOCK(dfs);
if (event == NULL) {
empty = 1;
break;
}
events_processed++;
re = *event;
OS_MEMZERO(event, sizeof(struct dfs_event));
ATH_DFSEVENTQ_LOCK(dfs);
STAILQ_INSERT_TAIL(&(dfs->dfs_eventq), event, re_list);
ATH_DFSEVENTQ_UNLOCK(dfs);
found = 0;
if (re.re_chanindex < DFS_NUM_RADAR_STATES)
rs = &dfs->dfs_radar[re.re_chanindex];
else {
ATH_DFSQ_LOCK(dfs);
empty = STAILQ_EMPTY(&(dfs->dfs_radarq));
ATH_DFSQ_UNLOCK(dfs);
continue;
}
if (rs->rs_chan.ic_flagext & CHANNEL_INTERFERENCE) {
ATH_DFSQ_LOCK(dfs);
empty = STAILQ_EMPTY(&(dfs->dfs_radarq));
ATH_DFSQ_UNLOCK(dfs);
continue;
}
if (dfs->dfs_rinfo.rn_lastfull_ts == 0) {
/*
* Either not started, or 64-bit rollover exactly to zero
* Just prepend zeros to the 15-bit ts
*/
dfs->dfs_rinfo.rn_ts_prefix = 0;
} else {
/* WAR 23031- patch duplicate ts on very short pulses */
/* This pacth has two problems in linux environment.
* 1)The time stamp created and hence PRI depends entirely on the latency.
* If the latency is high, it possibly can split two consecutive
* pulses in the same burst so far away (the same amount of latency)
* that make them look like they are from differenct bursts. It is
* observed to happen too often. It sure makes the detection fail.
* 2)Even if the latency is not that bad, it simply shifts the duplicate
* timestamps to a new duplicate timestamp based on how they are processed.
* This is not worse but not good either.
*
* Take this pulse as a good one and create a probable PRI later
*/
if (re.re_dur == 0 && re.re_ts == dfs->dfs_rinfo.rn_last_unique_ts) {
debug_dup[debug_dup_cnt++] = '1';
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1, "\n %s deltaT is 0 \n", __func__);
} else {
dfs->dfs_rinfo.rn_last_unique_ts = re.re_ts;
debug_dup[debug_dup_cnt++] = '0';
}
if (debug_dup_cnt >= 32) {
debug_dup_cnt = 0;
}
if (re.re_ts <= dfs->dfs_rinfo.rn_last_ts) {
dfs->dfs_rinfo.rn_ts_prefix +=
(((u_int64_t) 1) << DFS_TSSHIFT);
/* Now, see if it's been more than 1 wrap */
deltafull_ts = re.re_full_ts - dfs->dfs_rinfo.rn_lastfull_ts;
if (deltafull_ts >
((u_int64_t)((DFS_TSMASK - dfs->dfs_rinfo.rn_last_ts) + 1 + re.re_ts)))
deltafull_ts -= (DFS_TSMASK - dfs->dfs_rinfo.rn_last_ts) + 1 + re.re_ts;
deltafull_ts = deltafull_ts >> DFS_TSSHIFT;
if (deltafull_ts > 1) {
dfs->dfs_rinfo.rn_ts_prefix +=
((deltafull_ts - 1) << DFS_TSSHIFT);
}
} else {
deltafull_ts = re.re_full_ts - dfs->dfs_rinfo.rn_lastfull_ts;
if (deltafull_ts > (u_int64_t) DFS_TSMASK) {
deltafull_ts = deltafull_ts >> DFS_TSSHIFT;
dfs->dfs_rinfo.rn_ts_prefix +=
((deltafull_ts - 1) << DFS_TSSHIFT);
}
}
/*
* This is called each time a channel change occurs, to (potentially) enable
* the radar code.
*/
int dfs_radar_enable(struct ieee80211com *ic,
struct ath_dfs_radar_tab_info *radar_info, int no_cac)
{
int is_ext_ch=IEEE80211_IS_CHAN_11N_HT40(ic->ic_curchan);
int is_fastclk = 0;
//u_int32_t rfilt;
struct ath_dfs *dfs=(struct ath_dfs *)ic->ic_dfs;
struct ieee80211_channel *chan=ic->ic_curchan, *ext_ch = NULL;
if (dfs == NULL) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "%s: ic_dfs is NULL\n",
__func__);
return -EIO;
}
ic->ic_dfs_disable(ic, no_cac);
/*
* Setting country code might change the DFS domain
* so initialize the DFS Radar filters
*/
dfs_init_radar_filters(ic, radar_info);
#if ATH_SUPPORT_DFS && ATH_SUPPORT_STA_DFS
if ((ic->ic_opmode == IEEE80211_M_HOSTAP || ic->ic_opmode == IEEE80211_M_IBSS ||
(ic->ic_opmode == IEEE80211_M_STA && ieee80211com_has_cap_ext(dfs->ic,IEEE80211_CEXT_STADFS)))) {
#else
if ((ic->ic_opmode == IEEE80211_M_HOSTAP || ic->ic_opmode == IEEE80211_M_IBSS)) {
#endif
if (IEEE80211_IS_CHAN_DFS(chan)) {
struct dfs_state *rs_pri=NULL, *rs_ext=NULL;
u_int8_t index_pri, index_ext;
#ifdef ATH_ENABLE_AR
dfs->dfs_proc_phyerr |= DFS_AR_EN;
#endif
dfs->dfs_proc_phyerr |= DFS_RADAR_EN;
//printk( "%s[%d]: ==== 0x%08x\n", __func__, __LINE__, dfs->dfs_proc_phyerr);
if (is_ext_ch) {
ext_ch = ieee80211_get_extchan(ic);
}
dfs_reset_alldelaylines(dfs);
rs_pri = dfs_getchanstate(dfs, &index_pri, 0);
if (ext_ch) {
rs_ext = dfs_getchanstate(dfs, &index_ext, 1);
}
if (rs_pri != NULL && ((ext_ch==NULL)||(rs_ext != NULL))) {
struct ath_dfs_phyerr_param pe;
OS_MEMSET(&pe, '\0', sizeof(pe));
if (index_pri != dfs->dfs_curchan_radindex)
dfs_reset_alldelaylines(dfs);
dfs->dfs_curchan_radindex = (int16_t) index_pri;
if (rs_ext)
dfs->dfs_extchan_radindex = (int16_t) index_ext;
ath_dfs_phyerr_param_copy(&pe,
&rs_pri->rs_param);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS3,
"%s: firpwr=%d, rssi=%d, height=%d, "
"prssi=%d, inband=%d, relpwr=%d, "
"relstep=%d, maxlen=%d\n",
__func__,
pe.pe_firpwr,
pe.pe_rrssi,
pe.pe_height,
pe.pe_prssi,
pe.pe_inband,
pe.pe_relpwr,
pe.pe_relstep,
pe.pe_maxlen
);
#if 0 //Not needed
/* Disable strong signal fast antenna diversity */
ath_hal_setcapability(ah, HAL_CAP_DIVERSITY,
HAL_CAP_STRONG_DIV, 1, NULL);
#endif
ic->ic_dfs_enable(ic, &is_fastclk, &pe);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "Enabled radar detection on channel %d\n",
chan->ic_freq);
dfs->dur_multiplier = is_fastclk ? DFS_FAST_CLOCK_MULTIPLIER : DFS_NO_FAST_CLOCK_MULTIPLIER;
DFS_DPRINTK(dfs, ATH_DEBUG_DFS3,
"%s: duration multiplier is %d\n", __func__, dfs->dur_multiplier);
} else
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "%s: No more radar states left\n",
__func__);
}
}
return 0;
}
int
dfs_control(struct ieee80211com *ic, u_int id,
void *indata, u_int32_t insize,
void *outdata, u_int32_t *outsize)
{
int error = 0;
struct ath_dfs_phyerr_param peout;
struct ath_dfs *dfs = (struct ath_dfs *)ic->ic_dfs;
struct dfs_ioctl_params *dfsparams;
u_int32_t val=0;
#ifndef ATH_DFS_RADAR_DETECTION_ONLY
struct dfsreq_nolinfo *nol;
u_int32_t *data = NULL;
#endif /* ATH_DFS_RADAR_DETECTION_ONLY */
int i;
if (dfs == NULL) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1, "%s DFS is null\n", __func__);
/* Enable/Disable DFS can be done prior to attach, So handle here */
switch (id) {
case DFS_DISABLE_DETECT:
ic->ic_dfs_state.ignore_dfs = 1;
DFS_PRINTK("%s enable detects, ignore_dfs %d\n",
__func__,
ic->ic_dfs_state.ignore_dfs ? 1:0);
break;
case DFS_ENABLE_DETECT:
ic->ic_dfs_state.ignore_dfs = 0;
DFS_PRINTK("%s enable detects, ignore_dfs %d\n",
__func__,
ic->ic_dfs_state.ignore_dfs ? 1:0);
break;
default:
error = -EINVAL;
break;
}
goto bad;
}
//printk("%s[%d] id =%d\n", __func__, __LINE__, id);
switch (id) {
case DFS_SET_THRESH:
if (insize < sizeof(struct dfs_ioctl_params) || !indata) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS1,
"%s: insize=%d, expected=%d bytes, indata=%p\n",
__func__, insize, sizeof(struct dfs_ioctl_params),
indata);
error = -EINVAL;
break;
}
dfsparams = (struct dfs_ioctl_params *) indata;
if (!dfs_set_thresholds(ic, DFS_PARAM_FIRPWR, dfsparams->dfs_firpwr))
error = -EINVAL;
if (!dfs_set_thresholds(ic, DFS_PARAM_RRSSI, dfsparams->dfs_rrssi))
error = -EINVAL;
if (!dfs_set_thresholds(ic, DFS_PARAM_HEIGHT, dfsparams->dfs_height))
error = -EINVAL;
if (!dfs_set_thresholds(ic, DFS_PARAM_PRSSI, dfsparams->dfs_prssi))
error = -EINVAL;
if (!dfs_set_thresholds(ic, DFS_PARAM_INBAND, dfsparams->dfs_inband))
error = -EINVAL;
/* 5413 speicfic */
if (!dfs_set_thresholds(ic, DFS_PARAM_RELPWR, dfsparams->dfs_relpwr))
error = -EINVAL;
if (!dfs_set_thresholds(ic, DFS_PARAM_RELSTEP, dfsparams->dfs_relstep))
error = -EINVAL;
if (!dfs_set_thresholds(ic, DFS_PARAM_MAXLEN, dfsparams->dfs_maxlen))
error = -EINVAL;
break;
case DFS_GET_THRESH:
if (!outdata || !outsize || *outsize <sizeof(struct dfs_ioctl_params)) {
error = -EINVAL;
break;
}
*outsize = sizeof(struct dfs_ioctl_params);
dfsparams = (struct dfs_ioctl_params *) outdata;
/*
* Fetch the DFS thresholds using the internal representation.
*/
(void) dfs_get_thresholds(ic, &peout);
/*
* Convert them to the dfs IOCTL representation.
*/
ath_dfs_dfsparam_to_ioctlparam(&peout, dfsparams);
break;
case DFS_RADARDETECTS:
if (!outdata || !outsize || *outsize < sizeof(u_int32_t)) {
error = -EINVAL;
break;
}
*outsize = sizeof (u_int32_t);
*((u_int32_t *)outdata) = dfs->ath_dfs_stats.num_radar_detects;
break;
case DFS_DISABLE_DETECT:
dfs->dfs_proc_phyerr &= ~DFS_RADAR_EN;
dfs->ic->ic_dfs_state.ignore_dfs = 1;
DFS_PRINTK("%s enable detects, ignore_dfs %d\n",
__func__,
dfs->ic->ic_dfs_state.ignore_dfs ? 1:0);
break;
case DFS_ENABLE_DETECT:
dfs->dfs_proc_phyerr |= DFS_RADAR_EN;
dfs->ic->ic_dfs_state.ignore_dfs = 0;
DFS_PRINTK("%s enable detects, ignore_dfs %d\n",
__func__,
dfs->ic->ic_dfs_state.ignore_dfs ? 1:0);
break;
case DFS_DISABLE_FFT:
//UMACDFS: TODO: val = ath_hal_dfs_config_fft(sc->sc_ah, false);
DFS_PRINTK("%s TODO disable FFT val=0x%x \n", __func__, val);
break;
case DFS_ENABLE_FFT:
//UMACDFS TODO: val = ath_hal_dfs_config_fft(sc->sc_ah, true);
DFS_PRINTK("%s TODO enable FFT val=0x%x \n", __func__, val);
break;
case DFS_SET_DEBUG_LEVEL:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
dfs->dfs_debug_mask= *(u_int32_t *)indata;
DFS_PRINTK("%s debug level now = 0x%x \n",
__func__,
dfs->dfs_debug_mask);
if (dfs->dfs_debug_mask & ATH_DEBUG_DFS3) {
/* Enable debug Radar Event */
dfs->dfs_event_log_on = 1;
} else {
dfs->dfs_event_log_on = 0;
}
break;
case DFS_SET_FALSE_RSSI_THRES:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
dfs->ath_dfs_false_rssi_thres= *(u_int32_t *)indata;
DFS_PRINTK("%s false RSSI threshold now = 0x%x \n",
__func__,
dfs->ath_dfs_false_rssi_thres);
break;
case DFS_SET_PEAK_MAG:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
dfs->ath_dfs_peak_mag= *(u_int32_t *)indata;
DFS_PRINTK("%s peak_mag now = 0x%x \n",
__func__,
dfs->ath_dfs_peak_mag);
break;
case DFS_GET_CAC_VALID_TIME:
if (!outdata || !outsize || *outsize < sizeof(u_int32_t)) {
error = -EINVAL;
break;
}
*outsize = sizeof (u_int32_t);
*((u_int32_t *)outdata) = dfs->ic->ic_dfs_state.cac_valid_time;
break;
case DFS_SET_CAC_VALID_TIME:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
dfs->ic->ic_dfs_state.cac_valid_time = *(u_int32_t *)indata;
DFS_PRINTK("%s dfs timeout = %d \n",
__func__,
dfs->ic->ic_dfs_state.cac_valid_time);
break;
case DFS_IGNORE_CAC:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
if (*(u_int32_t *)indata) {
dfs->ic->ic_dfs_state.ignore_cac= 1;
} else {
dfs->ic->ic_dfs_state.ignore_cac= 0;
}
DFS_PRINTK("%s ignore cac = 0x%x \n",
__func__,
dfs->ic->ic_dfs_state.ignore_cac);
break;
case DFS_SET_NOL_TIMEOUT:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
if (*(int *)indata) {
dfs->ath_dfs_nol_timeout= *(int *)indata;
} else {
dfs->ath_dfs_nol_timeout= DFS_NOL_TIMEOUT_S;
}
DFS_PRINTK("%s nol timeout = %d sec \n",
__func__,
dfs->ath_dfs_nol_timeout);
break;
#ifndef ATH_DFS_RADAR_DETECTION_ONLY
case DFS_MUTE_TIME:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
data = (u_int32_t *) indata;
dfs->ath_dfstesttime = *data;
dfs->ath_dfstesttime *= (1000); //convert sec into ms
break;
case DFS_GET_USENOL:
if (!outdata || !outsize || *outsize < sizeof(u_int32_t)) {
error = -EINVAL;
break;
}
*outsize = sizeof(u_int32_t);
*((u_int32_t *)outdata) = dfs->dfs_rinfo.rn_use_nol;
printk("%s:#Phyerr=%d, #false detect=%d, #queued=%d\n", __func__,dfs->dfs_phyerr_count, dfs->dfs_phyerr_reject_count, dfs->dfs_phyerr_queued_count);
printk("%s:dfs_phyerr_freq_min=%d, dfs_phyerr_freq_max=%d\n", __func__,dfs->dfs_phyerr_freq_min, dfs->dfs_phyerr_freq_max);
printk("%s:Total radar events detected=%d, entries in the radar queue follows:\n", __func__,dfs->dfs_event_log_count);
for (i = 0; (i < DFS_EVENT_LOG_SIZE) && (i < dfs->dfs_event_log_count); i++) {
//DFS_DPRINTK(sc, ATH_DEBUG_DFS,"ts=%llu diff_ts=%u rssi=%u dur=%u\n", dfs->radar_log[i].ts, dfs->radar_log[i].diff_ts, dfs->radar_log[i].rssi, dfs->radar_log[i].dur);
printk("ts=%llu diff_ts=%u rssi=%u dur=%u\n", dfs->radar_log[i].ts, dfs->radar_log[i].diff_ts, dfs->radar_log[i].rssi, dfs->radar_log[i].dur);
}
dfs->dfs_event_log_count = 0;
dfs->dfs_phyerr_count = 0;
dfs->dfs_phyerr_reject_count = 0;
dfs->dfs_phyerr_queued_count = 0;
dfs->dfs_phyerr_freq_min = 0x7fffffff;
dfs->dfs_phyerr_freq_max = 0;
break;
case DFS_SET_USENOL:
if (insize < sizeof(u_int32_t) || !indata) {
error = -EINVAL;
break;
}
dfs->dfs_rinfo.rn_use_nol = *(u_int32_t *)indata;
/* iwpriv markdfs in linux can do the same thing... */
break;
case DFS_GET_NOL:
if (!outdata || !outsize || *outsize < sizeof(struct dfsreq_nolinfo)) {
error = -EINVAL;
break;
}
*outsize = sizeof(struct dfsreq_nolinfo);
nol = (struct dfsreq_nolinfo *)outdata;
dfs_get_nol(dfs, (struct dfsreq_nolelem *)nol->dfs_nol, &nol->ic_nchans);
dfs_print_nol(dfs);
break;
case DFS_SET_NOL:
if (insize < sizeof(struct dfsreq_nolinfo) || !indata) {
error = -EINVAL;
break;
}
nol = (struct dfsreq_nolinfo *) indata;
dfs_set_nol(dfs, (struct dfsreq_nolelem *)nol->dfs_nol, nol->ic_nchans);
break;
case DFS_SHOW_NOL:
dfs_print_nol(dfs);
break;
#if ATH_SUPPORT_DFS && ATH_SUPPORT_STA_DFS
case DFS_SHOW_NOLHISTORY:
dfs_print_nolhistory(ic,dfs);
break;
#endif
case DFS_BANGRADAR:
#if 0 //MERGE_TBD
if(sc->sc_nostabeacons)
{
printk("No radar detection Enabled \n");
break;
}
#endif
dfs->dfs_bangradar = 1;
dfs->ath_radar_tasksched = 1;
OS_SET_TIMER(&dfs->ath_dfs_task_timer, 0);
break;
#endif /* ATH_DFS_RADAR_DETECTION_ONLY */
default:
error = -EINVAL;
}
bad:
return error;
}
/*
* Find the channel information according to the scan entry
*/
int rtt_find_channel_info (void *arg, wlan_scan_entry_t scan_entry)
{
wmi_channel *wmi_chan;
u_int32_t chan_mode;
struct ieee80211com *ic;
struct ieee80211_channel *se_chan;
static const u_int modeflags[] = {
0, /* IEEE80211_MODE_AUTO */
MODE_11A, /* IEEE80211_MODE_11A */
MODE_11B, /* IEEE80211_MODE_11B */
MODE_11G, /* IEEE80211_MODE_11G */
0, /* IEEE80211_MODE_FH */
0, /* IEEE80211_MODE_TURBO_A */
0, /* IEEE80211_MODE_TURBO_G */
MODE_11NA_HT20, /* IEEE80211_MODE_11NA_HT20 */
MODE_11NG_HT20, /* IEEE80211_MODE_11NG_HT20 */
MODE_11NA_HT40, /* IEEE80211_MODE_11NA_HT40PLUS */
MODE_11NA_HT40, /* IEEE80211_MODE_11NA_HT40MINUS */
MODE_11NG_HT40, /* IEEE80211_MODE_11NG_HT40PLUS */
MODE_11NG_HT40, /* IEEE80211_MODE_11NG_HT40MINUS */
MODE_11NG_HT40, /* IEEE80211_MODE_11NG_HT40 */
MODE_11NA_HT40, /* IEEE80211_MODE_11NA_HT40 */
MODE_11AC_VHT20, /* IEEE80211_MODE_11AC_VHT20 */
MODE_11AC_VHT40, /* IEEE80211_MODE_11AC_VHT40PLUS */
MODE_11AC_VHT40, /* IEEE80211_MODE_11AC_VHT40MINUS*/
MODE_11AC_VHT40, /* IEEE80211_MODE_11AC_VHT40 */
MODE_11AC_VHT80, /* IEEE80211_MODE_11AC_VHT80 */
};
adf_os_print("%s:\n", __func__);
if (!(arg && scan_entry)) {
return -1; //critical error
}
wmi_chan = ((channel_search *)arg)->channel;
ic = ((channel_search *)arg)->ic;
if(!(wmi_chan && ic)) {
return -1; //critical error
}
se_chan = wlan_scan_entry_channel(scan_entry);
if(!se_chan) {
return -1; //critical error
}
wmi_chan->mhz = ieee80211_chan2freq(ic,se_chan);
chan_mode = ieee80211_chan2mode(se_chan);
WMI_SET_CHANNEL_MODE(wmi_chan, modeflags[chan_mode]);
if(chan_mode == IEEE80211_MODE_11AC_VHT80) {
if (se_chan->ic_ieee < 20) {
wmi_chan->band_center_freq1 = ieee80211_ieee2mhz(
se_chan->ic_vhtop_ch_freq_seg1,
IEEE80211_CHAN_2GHZ);
} else {
wmi_chan->band_center_freq1 = ieee80211_ieee2mhz(
se_chan->ic_vhtop_ch_freq_seg1,
IEEE80211_CHAN_5GHZ);
}
} else if((chan_mode == IEEE80211_MODE_11NA_HT40PLUS) ||
(chan_mode == IEEE80211_MODE_11NG_HT40PLUS) ||
(chan_mode == IEEE80211_MODE_11AC_VHT40PLUS)) {
wmi_chan->band_center_freq1 = wmi_chan->mhz + 10;
} else if((chan_mode == IEEE80211_MODE_11NA_HT40MINUS) ||
(chan_mode == IEEE80211_MODE_11NG_HT40MINUS) ||
(chan_mode == IEEE80211_MODE_11AC_VHT40MINUS)) {
wmi_chan->band_center_freq1 = wmi_chan->mhz - 10;
} else {
wmi_chan->band_center_freq1 = wmi_chan->mhz;
}
/* we do not support HT80PLUS80 yet */
wmi_chan->band_center_freq2=0;
WMI_SET_CHANNEL_MIN_POWER(wmi_chan, se_chan->ic_minpower);
WMI_SET_CHANNEL_MAX_POWER(wmi_chan, se_chan->ic_maxpower);
WMI_SET_CHANNEL_REG_POWER(wmi_chan, se_chan->ic_maxregpower);
WMI_SET_CHANNEL_ANTENNA_MAX(wmi_chan, se_chan->ic_antennamax);
WMI_SET_CHANNEL_REG_CLASSID(wmi_chan, se_chan->ic_regClassId);
if (IEEE80211_IS_CHAN_DFS(se_chan))
WMI_SET_CHANNEL_FLAG(wmi_chan, WMI_CHAN_FLAG_DFS);
adf_os_print("WMI channel freq=%d, mode=%x band_center_freq1=%d\n", wmi_chan->mhz,
WMI_GET_CHANNEL_MODE(wmi_chan), wmi_chan->band_center_freq1);
return 1; //seccessful!
}
static int
ol_vdev_wmi_event_handler(ol_scn_t scn, u_int8_t *data, u_int16_t datalen, void *context)
{
ieee80211_resmgr_t resmgr = (ieee80211_resmgr_t )context;
wmi_vdev_start_response_event *wmi_vdev_start_resp_ev =
(wmi_vdev_start_response_event *)data;
wlan_if_t vaphandle;
struct ieee80211com *ic = resmgr->ic;
struct ieee80211_channel *chan = NULL;
struct ieee80211_node *ni;
u_int8_t numvaps, actidx = 0;
struct ol_ath_vap_net80211 *avn;
bool do_notify = true;
vaphandle = ol_ath_vap_get(scn, wmi_vdev_start_resp_ev->vdev_id);
if (NULL == vaphandle) {
printk("Event received for Invalid/Deleted vap handle\n");
return 0;
}
avn = OL_ATH_VAP_NET80211(vaphandle);
printk("ol_vdev_start_resp_ev for vap %d (%p)\n", wmi_vdev_start_resp_ev->vdev_id, scn->wmi_handle);
spin_lock(&vaphandle->init_lock);
switch (vaphandle->iv_opmode) {
case IEEE80211_M_MONITOR:
/* Handle same as HOSTAP */
case IEEE80211_M_HOSTAP:
/* If vap is not waiting for the WMI event from target
return here
*/
if(avn->av_ol_resmgr_wait == FALSE) {
spin_unlock(&vaphandle->init_lock);
return 0;
}
/* Resetting the ol_resmgr_wait flag*/
avn->av_ol_resmgr_wait = FALSE;
numvaps = ieee80211_vaps_active(ic);
chan = vaphandle->iv_des_chan[vaphandle->iv_des_mode];
/*
* if there is a vap already running.
* ignore the desired channel and use the
* operating channel of the other vap.
*/
/* so that cwm can do its own crap. need to untie from state */
/* vap join is called here to wake up the chip if it is in sleep state */
ieee80211_vap_join(vaphandle);
if (numvaps == 0) {
//AP_DFS: ieee80211_set_channel(ic, chan);
if (wmi_vdev_start_resp_ev->resp_type != WMI_VDEV_RESTART_RESP_EVENT) {
/* 20/40 Mhz coexistence handler */
if ((avn->av_ol_resmgr_chan != NULL) && (chan != avn->av_ol_resmgr_chan)) {
chan = avn->av_ol_resmgr_chan;
}
ic->ic_prevchan = ic->ic_curchan;
ic->ic_curchan = chan;
/*update channel history*/
actidx = ic->ic_chanidx;
ic->ic_chanhist[actidx].chanid = (ic->ic_curchan)->ic_ieee;
ic->ic_chanhist[actidx].chanjiffies = OS_GET_TIMESTAMP();
ic->ic_chanidx == (IEEE80211_CHAN_MAXHIST - 1) ? ic->ic_chanidx = 0 : ++(ic->ic_chanidx);
/* update max channel power to max regpower of current channel */
ieee80211com_set_curchanmaxpwr(ic, chan->ic_maxregpower);
ieee80211_wme_initparams(vaphandle);
}
/* ieee80211 Layer - Default Configuration */
vaphandle->iv_bsschan = ic->ic_curchan;
/* XXX reset erp state */
ieee80211_reset_erp(ic, ic->ic_curmode, vaphandle->iv_opmode);
} else {
/* ieee80211 Layer - Default Configuration */
vaphandle->iv_bsschan = ic->ic_curchan;
}
/* use the vap bsschan for dfs configure */
if ( IEEE80211_IS_CHAN_DFS(vaphandle->iv_bsschan)) {
extern void ol_if_dfs_configure(struct ieee80211com *ic);
ol_if_dfs_configure(ic);
}
break;
case IEEE80211_M_STA:
ni = vaphandle->iv_bss;
chan = ni->ni_chan;
vaphandle->iv_bsschan = chan;
ic->ic_prevchan = ic->ic_curchan;
ic->ic_curchan = chan;
/* update max channel power to max regpower of current channel */
ieee80211com_set_curchanmaxpwr(ic, chan->ic_maxregpower);
/* ieee80211 Layer - Default Configuration */
vaphandle->iv_bsschan = ic->ic_curchan;
/* XXX reset erp state */
ieee80211_reset_erp(ic, ic->ic_curmode, vaphandle->iv_opmode);
ieee80211_wme_initparams(vaphandle);
if (wmi_vdev_start_resp_ev->resp_type == WMI_VDEV_RESTART_RESP_EVENT) {
do_notify = false;
}
break;
default:
break;
}
vaphandle->init_in_progress = false;
spin_unlock(&vaphandle->init_lock);
/* Intimate start completion to VAP module */
/* if STA, bypass notification for RESTERT EVENT */
if (do_notify)
ieee80211_notify_vap_start_complete(resmgr, vaphandle, IEEE80211_RESMGR_STATUS_SUCCESS);
return 0;
}
/*
* This is called each time a channel change occurs, to (potentially) enable
* the radar code.
*/
int dfs_radar_enable(struct ieee80211com *ic,
struct ath_dfs_radar_tab_info *radar_info)
{
int is_ext_ch;
int is_fastclk = 0;
int radar_filters_init_status = 0;
//u_int32_t rfilt;
struct ath_dfs *dfs;
struct dfs_state *rs_pri, *rs_ext;
struct ieee80211_channel *chan=ic->ic_curchan, *ext_ch = NULL;
is_ext_ch=IEEE80211_IS_CHAN_11N_HT40(ic->ic_curchan);
dfs=(struct ath_dfs *)ic->ic_dfs;
rs_pri = NULL;
rs_ext = NULL;
#if 0
int i;
#endif
if (dfs == NULL) {
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "%s: ic_dfs is NULL\n",
__func__);
return -EIO;
}
ic->ic_dfs_disable(ic);
/*
* Setting country code might change the DFS domain
* so initialize the DFS Radar filters
*/
radar_filters_init_status = dfs_init_radar_filters(ic, radar_info);
/*
* dfs_init_radar_filters() returns 1 on failure and
* 0 on success.
*/
if ( DFS_STATUS_FAIL == radar_filters_init_status ) {
VOS_TRACE(VOS_MODULE_ID_SAP, VOS_TRACE_LEVEL_ERROR,
"%s[%d]: DFS Radar Filters Initialization Failed",
__func__, __LINE__);
return -EIO;
}
if ((ic->ic_opmode == IEEE80211_M_HOSTAP || ic->ic_opmode == IEEE80211_M_IBSS)) {
if (IEEE80211_IS_CHAN_DFS(chan)) {
u_int8_t index_pri, index_ext;
#ifdef ATH_ENABLE_AR
dfs->dfs_proc_phyerr |= DFS_AR_EN;
#endif
dfs->dfs_proc_phyerr |= DFS_RADAR_EN;
if (is_ext_ch) {
ext_ch = ieee80211_get_extchan(ic);
}
dfs_reset_alldelaylines(dfs);
rs_pri = dfs_getchanstate(dfs, &index_pri, 0);
if (ext_ch) {
rs_ext = dfs_getchanstate(dfs, &index_ext, 1);
}
if (rs_pri != NULL && ((ext_ch==NULL)||(rs_ext != NULL))) {
struct ath_dfs_phyerr_param pe;
OS_MEMSET(&pe, '\0', sizeof(pe));
if (index_pri != dfs->dfs_curchan_radindex)
dfs_reset_alldelaylines(dfs);
dfs->dfs_curchan_radindex = (int16_t) index_pri;
dfs->dfs_pri_multiplier_ini = radar_info->dfs_pri_multiplier;
if (rs_ext)
dfs->dfs_extchan_radindex = (int16_t) index_ext;
ath_dfs_phyerr_param_copy(&pe,
&rs_pri->rs_param);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS3,
"%s: firpwr=%d, rssi=%d, height=%d, "
"prssi=%d, inband=%d, relpwr=%d, "
"relstep=%d, maxlen=%d\n",
__func__,
pe.pe_firpwr,
pe.pe_rrssi,
pe.pe_height,
pe.pe_prssi,
pe.pe_inband,
pe.pe_relpwr,
pe.pe_relstep,
pe.pe_maxlen
);
ic->ic_dfs_enable(ic, &is_fastclk, &pe);
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "Enabled radar detection on channel %d\n",
chan->ic_freq);
dfs->dur_multiplier =
is_fastclk ? DFS_FAST_CLOCK_MULTIPLIER : DFS_NO_FAST_CLOCK_MULTIPLIER;
DFS_DPRINTK(dfs, ATH_DEBUG_DFS3,
"%s: duration multiplier is %d\n", __func__, dfs->dur_multiplier);
} else
DFS_DPRINTK(dfs, ATH_DEBUG_DFS, "%s: No more radar states left\n",
__func__);
}
}
return DFS_STATUS_SUCCESS;
}
