/**********************************************************
Sends parameters for initialization of GSM module
group: 0 - parameters of group 0 - not necessary to be registered in the GSM
1 - parameters of group 1 - it is necessary to be registered
**********************************************************/
void GSM::InitParam(byte group)
{
switch (group) {
case PARAM_SET_0:
// check comm line
if (CLS_FREE != GetCommLineStatus()) return;
SetCommLineStatus(CLS_ATCMD);
// Reset to the factory settings
SendATCmdWaitResp("AT&F0", 1000, 20, "OK", 5);
// switch off echo
SendATCmdWaitResp("ATE0", 500, 20, "OK", 5);
// setup auto baud rate
SendATCmdWaitResp("AT+IPR=0", 500, 20, "OK", 5);
SetCommLineStatus(CLS_FREE);
break;
case PARAM_SET_1:
// check comm line
if (CLS_FREE != GetCommLineStatus()) return;
SetCommLineStatus(CLS_ATCMD);
// set the SMS mode to text
SendATCmdWaitResp("AT+CMGF=1", 500, 20, "OK", 5);
// init SMS storage
InitSMSMemory();
// select phonebook memory storage
SendATCmdWaitResp("AT+CPBS=\"SM\"", 1000, 20, "OK", 5);
break;
}
}
void GSM::InitParam(byte group){
switch (group) {
case PARAM_SET_0:
// check comm line
//if (CLS_FREE != GetCommLineStatus()) return;
SetCommLineStatus(CLS_ATCMD);
// Reset to the factory settings
SendATCmdWaitResp("AT&F", 1000, 50, "OK", 5);
// switch off echo
SendATCmdWaitResp("ATE0", 500, 50, "OK", 5);
// setup fixed baud rate
//SendATCmdWaitResp("AT+IPR=9600", 500, 50, "OK", 5);
// setup mode
//SendATCmdWaitResp("AT#SELINT=1", 500, 50, "OK", 5);
// Switch ON User LED - just as signalization we are here
//SendATCmdWaitResp("AT#GPIO=8,1,1", 500, 50, "OK", 5);
// Sets GPIO9 as an input = user button
//SendATCmdWaitResp("AT#GPIO=9,0,0", 500, 50, "OK", 5);
// allow audio amplifier control
//SendATCmdWaitResp("AT#GPIO=5,0,2", 500, 50, "OK", 5);
// Switch OFF User LED- just as signalization we are finished
//SendATCmdWaitResp("AT#GPIO=8,0,1", 500, 50, "OK", 5);
SetCommLineStatus(CLS_FREE);
break;
case PARAM_SET_1:
// check comm line
//if (CLS_FREE != GetCommLineStatus()) return;
SetCommLineStatus(CLS_ATCMD);
// Request calling line identification
SendATCmdWaitResp(F("AT+CLIP=1"), 500, 50, "OK", 5);
// Mobile Equipment Error Code
SendATCmdWaitResp(F("AT+CMEE=0"), 500, 50, "OK", 5);
// Echo canceller enabled
//SendATCmdWaitResp("AT#SHFEC=1", 500, 50, "OK", 5);
// Ringer tone select (0 to 32)
//SendATCmdWaitResp("AT#SRS=26,0", 500, 50, "OK", 5);
// Microphone gain (0 to 7) - response here sometimes takes
// more than 500msec. so 1000msec. is more safety
//SendATCmdWaitResp("AT#HFMICG=7", 1000, 50, "OK", 5);
// set the SMS mode to text
SendATCmdWaitResp(F("AT+CMGF=1"), 500, 50, "OK", 5);
// Auto answer after first ring enabled
// auto answer is not used
//SendATCmdWaitResp("ATS0=1", 500, 50, "OK", 5);
// select ringer path to handsfree
//SendATCmdWaitResp("AT#SRP=1", 500, 50, "OK", 5);
// select ringer sound level
//SendATCmdWaitResp("AT+CRSL=2", 500, 50, "OK", 5);
// we must release comm line because SetSpeakerVolume()
// checks comm line if it is free
SetCommLineStatus(CLS_FREE);
// select speaker volume (0 to 14)
//SetSpeakerVolume(9);
// init SMS storage
InitSMSMemory();
// select phonebook memory storage
SendATCmdWaitResp(F("AT+CPBS=\"SM\""), 1000, 50, "OK", 5);
SendATCmdWaitResp(F("AT+CIPSHUT"), 500, 50, "SHUT OK", 5);
break;
}
}
