int main()
{
uint8 ch; /* Data sent on the serial port */
uint8 count = 0u; /* Initializing the count value */
uint8 pos = 0u;
CyGlobalIntEnable;
isr_1_Start(); /* Initializing the ISR */
UART_1_Start(); /* Enabling the UART */
LCD_Char_1_Start(); /* Enabling the LCD */
for(ch = START_CHAR_VALUE; ch <= END_CHAR_VALUE; ch++)
{
UART_1_WriteTxData(ch); /* Sending the data */
count++;
if(count % LCD_NUM_COLUMNS == 0u) /* If the count value reaches the count 16 start from first location */
{
pos = 0u; /* resets the count value */
LCD_Char_1_WriteControl(LCD_Char_1_CLEAR_DISPLAY); /* Display will be cleared when reached count value 16 */
}
LCD_Char_1_Position(0u, pos++); /* LCD position to the count++ */
LCD_Char_1_PutChar(ch); /* print the value in the LCD */
LCD_Char_1_Position(1u, 0u);
LCD_Char_1_PrintInt8(count); /* prints the count in the LCD */
CyDelay(200u);
}
for(;;) {}
}
/*******************************************************************************
* Function Name: LCD_Char_1_Init
********************************************************************************
*
* Summary:
* Perform initialization required for the components normal work.
* This function initializes the LCD hardware module as follows:
* Enables a 4-bit interface
* Clears the display
* Enables the auto cursor increment
* Resets the cursor to start position
* Also, it loads a custom character set to the LCD if it was defined in the customizer.
*
* Parameters:
* None.
*
* Return:
* None.
*
* Reentrant:
* No.
*
*******************************************************************************/
void LCD_Char_1_Init(void)
{
/* INIT CODE */
CyDelay(40u); /* Delay 40 ms */
LCD_Char_1_WrCntrlNib(LCD_Char_1_DISPLAY_8_BIT_INIT); /* Selects 8-bit mode */
CyDelay(5u); /* Delay 5 ms */
LCD_Char_1_WrCntrlNib(LCD_Char_1_DISPLAY_8_BIT_INIT); /* Selects 8-bit mode */
CyDelay(15u); /* Delay 15 ms */
LCD_Char_1_WrCntrlNib(LCD_Char_1_DISPLAY_8_BIT_INIT); /* Selects 8-bit mode */
CyDelay(1u); /* Delay 1 ms */
LCD_Char_1_WrCntrlNib(LCD_Char_1_DISPLAY_4_BIT_INIT); /* Selects 4-bit mode */
CyDelay(5u); /* Delay 5 ms */
LCD_Char_1_WriteControl(LCD_Char_1_CURSOR_AUTO_INCR_ON); /* Incr Cursor After Writes */
LCD_Char_1_WriteControl(LCD_Char_1_DISPLAY_CURSOR_ON); /* Turn Display, Cursor ON */
LCD_Char_1_WriteControl(LCD_Char_1_DISPLAY_2_LINES_5x10); /* 2 Lines by 5x10 Characters */
LCD_Char_1_WriteControl(LCD_Char_1_DISPLAY_CURSOR_OFF); /* Turn Display, Cursor OFF */
LCD_Char_1_WriteControl(LCD_Char_1_CLEAR_DISPLAY); /* Clear LCD Screen */
LCD_Char_1_WriteControl(LCD_Char_1_DISPLAY_ON_CURSOR_OFF); /* Turn Display ON, Cursor OFF */
LCD_Char_1_WriteControl(LCD_Char_1_RESET_CURSOR_POSITION); /* Set Cursor to 0,0 */
CyDelay(5u);
#if(LCD_Char_1_CUSTOM_CHAR_SET != LCD_Char_1_NONE)
LCD_Char_1_LoadCustomFonts(LCD_Char_1_customFonts);
#endif /* LCD_Char_1_CUSTOM_CHAR_SET != LCD_Char_1_NONE */
}
/*******************************************************************************
* Function Name: LCD_Char_1_LoadCustomFonts
********************************************************************************
*
* Summary:
* Loads 8 custom font characters into the LCD Module for use. Cannot use
* characters from two different font sets at once, but font sets can be
* switched out during runtime.
*
* Parameters:
* customData: pointer to a constant array of 64 bytes representing 8 custom
* font characters.
* Return:
* None.
*
* Theory:
* Prior to using this function user need to import the pointer to custom
* font array to your project by writting the following in the source code file
* where custom font will be used:
* extern uint8 const CYCODE LCD_Char_customFonts[];
* This function is not automatically called by the Start() routine and must be
* called manually by the user.
*******************************************************************************/
void LCD_Char_1_LoadCustomFonts(const uint8* customData)
{
uint8 indexU8;
LCD_Char_1_IsReady();
/* Set starting address in the LCD Module */
/* Optionally: Read the current address to restore at a later time */
LCD_Char_1_WriteControl(LCD_Char_1_CGRAM_0);
/* Load in the 64 bytes of CustomChar Data */
for(indexU8 = 0u; indexU8 < LCD_Char_1_CUSTOM_CHAR_SET_LEN; indexU8++)
{
/* Delay between each write */
LCD_Char_1_WriteData(customData[indexU8]);
}
LCD_Char_1_IsReady();
LCD_Char_1_WriteControl(LCD_Char_1_DDRAM_0);
}
/*******************************************************************************
* Function Name: LCD_Char_1_Position
********************************************************************************
*
* Summary:
* Moves the active cursor location to a point specified by the input arguments
*
* Parameters:
* row: Specific row of LCD module to be written
* column: Column of LCD module to be written
*
* Return:
* None.
*
* Note:
* This only applies for LCD displays that use the 2X40 address mode.
* In this case Row 2 starts with 0x28 offset from Row 1.
* When there are more than 2 rows, each row must be fewer than 20 characters.
*
*******************************************************************************/
void LCD_Char_1_Position(uint8 row, uint8 column)
{
switch (row)
{
case (uint8)0:
LCD_Char_1_WriteControl(LCD_Char_1_ROW_0_START + column);
break;
case (uint8) 1:
LCD_Char_1_WriteControl(LCD_Char_1_ROW_1_START + column);
break;
case (uint8) 2:
LCD_Char_1_WriteControl(LCD_Char_1_ROW_2_START + column);
break;
case (uint8) 3:
LCD_Char_1_WriteControl(LCD_Char_1_ROW_3_START + column);
break;
default:
/* if default case is hit, invalid row argument was passed.*/
break;
}
}
