/*
==========================================================================
Description:
This routine is executed every second -
1. Decide the overall channel quality
2. Check if need to upgrade the TX rate to any client
3. perform MAC table maintenance, including ageout no-traffic clients,
and release packet buffer in PSQ is fail to TX in time.
==========================================================================
*/
VOID APMlmePeriodicExec(
PRTMP_ADAPTER pAd)
{
/*
Reqeust by David 2005/05/12
It make sense to disable Adjust Tx Power on AP mode, since we can't
take care all of the client's situation
ToDo: need to verify compatibility issue with WiFi product.
*/
#ifdef CARRIER_DETECTION_SUPPORT
if (isCarrierDetectExist(pAd) == TRUE)
{
PCARRIER_DETECTION_STRUCT pCarrierDetect = &pAd->CommonCfg.CarrierDetect;
if (pCarrierDetect->OneSecIntCount < pCarrierDetect->CarrierGoneThreshold)
{
pCarrierDetect->CD_State = CD_NORMAL;
pCarrierDetect->recheck = pCarrierDetect->recheck1;
if (pCarrierDetect->Debug != RT_DEBUG_TRACE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Carrier gone\n"));
/* start all TX actions. */
APMakeAllBssBeacon(pAd);
APUpdateAllBeaconFrame(pAd);
AsicEnableBssSync(pAd);
}
else
{
printk("Carrier gone\n");
}
}
pCarrierDetect->OneSecIntCount = 0;
}
#endif /* CARRIER_DETECTION_SUPPORT */
RTMP_CHIP_HIGH_POWER_TUNING(pAd, &pAd->ApCfg.RssiSample);
/* Disable Adjust Tx Power for WPA WiFi-test. */
/* Because high TX power results in the abnormal disconnection of Intel BG-STA. */
/*#ifndef WIFI_TEST */
/* if (pAd->CommonCfg.bWiFiTest == FALSE) */
/* for SmartBit 64-byte stream test */
/* removed based on the decision of Ralink congress at 2011/7/06 */
/* if (pAd->MacTab.Size > 0) */
AsicAdjustTxPower(pAd);
/*#endif // WIFI_TEST */
#ifdef RTMP_TEMPERATURE_COMPENSATION
MT76x0_TemperatureCompensation(pAd);
#endif /* RTMP_TEMPERATURE_COMPENSATION */
/* BBP TUNING: dynamic tune BBP R66 to find a balance between sensibility
and noise isolation */
/* AsicBbpTuning2(pAd); */
/* walk through MAC table, see if switching TX rate is required */
/* MAC table maintenance */
if (pAd->Mlme.PeriodicRound % MLME_TASK_EXEC_MULTIPLE == 0)
{
/* one second timer */
MacTableMaintenance(pAd);
#ifdef FPGA_MODE
if (pAd->fpga_tr_stop)
{
UINT32 mac_val;
/* enable/disable tx/rx*/
RTMP_IO_READ32(pAd, MAC_SYS_CTRL, &mac_val);
switch (pAd->fpga_tr_stop)
{
case 3: //stop tx + rx
mac_val &= (~0xc);
break;
case 2: // stop rx
mac_val &= (~0x8);
break;
case 1: // stop tx
mac_val &= (~0x4);
break;
case 4:
default:
mac_val |= 0x0c;
break;
}
RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, mac_val);
}
#endif /* FGPA_MODE */
RTMPMaintainPMKIDCache(pAd);
#ifdef WDS_SUPPORT
WdsTableMaintenance(pAd);
#endif /* WDS_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabMaintain(pAd);
#endif /* CLIENT_WDS */
}
APUpdateCapabilityAndErpIe(pAd);
#ifdef APCLI_SUPPORT
if (pAd->Mlme.OneSecPeriodicRound % 2 == 0)
ApCliIfMonitor(pAd);
if (pAd->Mlme.OneSecPeriodicRound % 2 == 1)
ApCliIfUp(pAd);
{
INT loop;
ULONG Now32;
UINT32 MaxWcidNum = MAX_LEN_OF_MAC_TABLE;
#ifdef MAC_REPEATER_SUPPORT
if (pAd->ApCfg.bMACRepeaterEn)
{
MaxWcidNum = MAX_MAC_TABLE_SIZE_WITH_REPEATER;
#ifdef APCLI_AUTO_CONNECT_SUPPORT
RTMPRepeaterReconnectionCheck(pAd);
#endif /* APCLI_AUTO_CONNECT_SUPPORT */
}
#endif /* MAC_REPEATER_SUPPORT */
NdisGetSystemUpTime(&Now32);
for (loop = 0; loop < MAX_APCLI_NUM; loop++)
{
PAPCLI_STRUCT pApCliEntry = &pAd->ApCfg.ApCliTab[loop];
if ((pApCliEntry->Valid == TRUE)
&& (pApCliEntry->MacTabWCID < MaxWcidNum))
{
/* update channel quality for Roaming and UI LinkQuality display */
MlmeCalculateChannelQuality(pAd,
&pAd->MacTab.Content[pApCliEntry->MacTabWCID], Now32);
}
}
}
#endif /* APCLI_SUPPORT */
#ifdef DOT11_N_SUPPORT
if (pAd->CommonCfg.bHTProtect)
{
/*APUpdateCapabilityAndErpIe(pAd); */
APUpdateOperationMode(pAd);
if (pAd->CommonCfg.IOTestParm.bRTSLongProtOn == FALSE)
{
AsicUpdateProtect(pAd, (USHORT)pAd->CommonCfg.AddHTInfo.AddHtInfo2.OperaionMode, ALLN_SETPROTECT, FALSE, pAd->MacTab.fAnyStationNonGF);
}
}
#endif /* DOT11_N_SUPPORT */
#ifdef A_BAND_SUPPORT
if ( (pAd->CommonCfg.Channel > 14)
&& (pAd->CommonCfg.bIEEE80211H == 1)
)
{
#ifdef DFS_SUPPORT
ApRadarDetectPeriodic(pAd);
#else
pAd->Dot11_H.InServiceMonitorCount++;
if (pAd->Dot11_H.RDMode == RD_SILENCE_MODE)
{
if (pAd->Dot11_H.RDCount++ > pAd->Dot11_H.ChMovingTime)
{
AsicEnableBssSync(pAd);
pAd->Dot11_H.RDMode = RD_NORMAL_MODE;
}
}
#endif /* !DFS_SUPPORT */
}
#endif /* A_BAND_SUPPORT */
/* resume Improved Scanning*/
if ((pAd->ApCfg.bImprovedScan) &&
(!RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_BSS_SCAN_IN_PROGRESS)) &&
(pAd->Mlme.ApSyncMachine.CurrState == AP_SCAN_PENDING))
{
MLME_SCAN_REQ_STRUCT ScanReq;
AsicDisableSync(pAd);
RTMPZeroMemory(ScanReq.Ssid, MAX_LEN_OF_SSID);
ScanReq.SsidLen = pAd->MlmeAux.SsidLen;
NdisMoveMemory(ScanReq.Ssid, pAd->MlmeAux.Ssid, ScanReq.SsidLen);
ScanReq.BssType = BSS_ANY;
#ifdef APCLI_CONNECTION_TRIAL
ScanReq.ScanType = FAST_SCAN_ACTIVE;
#else
ScanReq.ScanType = SCAN_ACTIVE;
#endif /* APCLI_CONNECTION_TRIAL */
MlmeEnqueue(pAd, AP_SYNC_STATE_MACHINE, APMT2_MLME_SCAN_REQ, sizeof(MLME_SCAN_REQ_STRUCT), &ScanReq, 0);
RTMP_MLME_HANDLER(pAd);
DBGPRINT(RT_DEBUG_TRACE, ("bImprovedScan ............. Resume for bImprovedScan, SCAN_PENDING .............. \n"));
}
}
/*
==========================================================================
Description:
This routine is executed every second -
1. Decide the overall channel quality
2. Check if need to upgrade the TX rate to any client
3. perform MAC table maintenance, including ageout no-traffic clients,
and release packet buffer in PSQ is fail to TX in time.
==========================================================================
*/
VOID APMlmePeriodicExec(
PRTMP_ADAPTER pAd)
{
/*
Reqeust by David 2005/05/12
It make sense to disable Adjust Tx Power on AP mode, since we can't
take care all of the client's situation
ToDo: need to verify compatibility issue with WiFi product.
*/
#ifdef CARRIER_DETECTION_SUPPORT
if (isCarrierDetectExist(pAd) == TRUE)
{
PCARRIER_DETECTION_STRUCT pCarrierDetect = &pAd->CommonCfg.CarrierDetect;
if (pCarrierDetect->OneSecIntCount < pCarrierDetect->CarrierGoneThreshold)
{
pCarrierDetect->CD_State = CD_NORMAL;
pCarrierDetect->recheck = pCarrierDetect->recheck1;
if (pCarrierDetect->Debug != RT_DEBUG_TRACE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Carrier gone\n"));
/* start all TX actions. */
APMakeAllBssBeacon(pAd);
APUpdateAllBeaconFrame(pAd);
AsicEnableBssSync(pAd, pAd->CommonCfg.BeaconPeriod);
}
else
{
DBGPRINT(RT_DEBUG_TRACE, ("Carrier gone\n"));
}
}
pCarrierDetect->OneSecIntCount = 0;
}
#endif /* CARRIER_DETECTION_SUPPORT */
RTMP_CHIP_HIGH_POWER_TUNING(pAd, &pAd->ApCfg.RssiSample);
/* Disable Adjust Tx Power for WPA WiFi-test. */
/* Because high TX power results in the abnormal disconnection of Intel BG-STA. */
/*#ifndef WIFI_TEST */
/* if (pAd->CommonCfg.bWiFiTest == FALSE) */
/* for SmartBit 64-byte stream test */
/* removed based on the decision of Ralink congress at 2011/7/06 */
/* if (pAd->MacTab.Size > 0) */
RTMP_CHIP_ASIC_ADJUST_TX_POWER(pAd);
/*#endif // WIFI_TEST */
RTMP_CHIP_ASIC_TEMPERATURE_COMPENSATION(pAd);
/* walk through MAC table, see if switching TX rate is required */
/* MAC table maintenance */
if (pAd->Mlme.PeriodicRound % MLME_TASK_EXEC_MULTIPLE == 0)
{
/* one second timer */
MacTableMaintenance(pAd);
#ifdef CONFIG_FPGA_MODE
if (pAd->fpga_ctl.fpga_tr_stop)
{
INT enable = FALSE, ctrl_type;
/* enable/disable tx/rx*/
switch (pAd->fpga_ctl.fpga_tr_stop)
{
case 3: //stop tx + rx
ctrl_type = ASIC_MAC_TXRX;
break;
case 2: // stop rx
ctrl_type = ASIC_MAC_RX;
break;
case 1: // stop tx
ctrl_type = ASIC_MAC_TX;
break;
case 4:
default:
enable = TRUE;
ctrl_type = ASIC_MAC_TXRX;
break;
}
AsicSetMacTxRx(pAd, ctrl_type, enable);
}
#endif /* CONFIG_FPGA_MODE */
RTMPMaintainPMKIDCache(pAd);
#ifdef WDS_SUPPORT
WdsTableMaintenance(pAd);
#endif /* WDS_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabMaintain(pAd);
#endif /* CLIENT_WDS */
}
#ifdef AP_SCAN_SUPPORT
AutoChannelSelCheck(pAd);
#endif /* AP_SCAN_SUPPORT */
APUpdateCapabilityAndErpIe(pAd);
#ifdef APCLI_SUPPORT
if (pAd->Mlme.OneSecPeriodicRound % 2 == 0)
ApCliIfMonitor(pAd);
if (pAd->Mlme.OneSecPeriodicRound % 2 == 1
#ifdef APCLI_AUTO_CONNECT_SUPPORT
&& (pAd->ApCfg.ApCliAutoConnectChannelSwitching == FALSE)
#endif /* APCLI_AUTO_CONNECT_SUPPORT */
) {
ApCliIfUp(pAd);
}
{
INT loop;
ULONG Now32;
#ifdef MAC_REPEATER_SUPPORT
if (pAd->ApCfg.bMACRepeaterEn)
{
RTMPRepeaterReconnectionCheck(pAd);
}
#endif /* MAC_REPEATER_SUPPORT */
NdisGetSystemUpTime(&Now32);
for (loop = 0; loop < MAX_APCLI_NUM; loop++)
{
PAPCLI_STRUCT pApCliEntry = &pAd->ApCfg.ApCliTab[loop];
if ((pApCliEntry->Valid == TRUE)
&& (pApCliEntry->MacTabWCID < MAX_LEN_OF_MAC_TABLE))
{
/* update channel quality for Roaming and UI LinkQuality display */
MlmeCalculateChannelQuality(pAd,
&pAd->MacTab.Content[pApCliEntry->MacTabWCID], Now32);
}
}
}
#endif /* APCLI_SUPPORT */
#ifdef DOT11_N_SUPPORT
if (pAd->CommonCfg.bHTProtect) {
/*APUpdateCapabilityAndErpIe(pAd); */
APUpdateOperationMode(pAd);
if (pAd->CommonCfg.IOTestParm.bRTSLongProtOn == FALSE)
AsicUpdateProtect(pAd, (USHORT)pAd->CommonCfg.AddHTInfo.AddHtInfo2.OperaionMode,
ALLN_SETPROTECT, FALSE, pAd->MacTab.fAnyStationNonGF);
}
#endif /* DOT11_N_SUPPORT */
#ifdef A_BAND_SUPPORT
if ( (pAd->CommonCfg.Channel > 14)
&& (pAd->CommonCfg.bIEEE80211H == 1))
{
#ifdef DFS_SUPPORT
ApRadarDetectPeriodic(pAd);
#else
pAd->Dot11_H.InServiceMonitorCount++;
if (pAd->Dot11_H.RDMode == RD_SILENCE_MODE)
{
if (pAd->Dot11_H.RDCount++ > pAd->Dot11_H.ChMovingTime)
{
AsicEnableBssSync(pAd, pAd->CommonCfg.BeaconPeriod);
pAd->Dot11_H.RDMode = RD_NORMAL_MODE;
}
}
#endif /* !DFS_SUPPORT */
}
#endif /* A_BAND_SUPPORT */
}
/*
==========================================================================
Description:
This routine is executed every second -
1. Decide the overall channel quality
2. Check if need to upgrade the TX rate to any client
3. perform MAC table maintenance, including ageout no-traffic clients,
and release packet buffer in PSQ is fail to TX in time.
==========================================================================
*/
VOID APMlmePeriodicExec(
PRTMP_ADAPTER pAd)
{
/*
Reqeust by David 2005/05/12
It make sense to disable Adjust Tx Power on AP mode, since we can't
take care all of the client's situation
ToDo: need to verify compatibility issue with WiFi product.
*/
/*
We return here in ATE mode, because the statistics
that ATE need are not collected via this routine.
*/
#ifdef RALINK_ATE
if (ATE_ON(pAd))
return;
#endif /* RALINK_ATE */
#ifdef CARRIER_DETECTION_SUPPORT
if (isCarrierDetectExist(pAd) == TRUE)
{
if (pAd->CommonCfg.CarrierDetect.OneSecIntCount < pAd->CommonCfg.CarrierDetect.CarrierGoneThreshold)
{
pAd->CommonCfg.CarrierDetect.CD_State = CD_NORMAL;
pAd->CommonCfg.CarrierDetect.recheck = pAd->CommonCfg.CarrierDetect.recheck1;
if (pAd->CommonCfg.CarrierDetect.Debug != RT_DEBUG_TRACE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Carrier gone\n"));
/* start all TX actions. */
APMakeAllBssBeacon(pAd);
APUpdateAllBeaconFrame(pAd);
AsicEnableBssSync(pAd);
}
else
{
printk("Carrier gone\n");
}
}
}
pAd->CommonCfg.CarrierDetect.OneSecIntCount = 0;
#endif /* CARRIER_DETECTION_SUPPORT */
RTMP_CHIP_HIGH_POWER_TUNING(pAd, &pAd->ApCfg.RssiSample);
/* Disable Adjust Tx Power for WPA WiFi-test. */
/* Because high TX power results in the abnormal disconnection of Intel BG-STA. */
/*#ifndef WIFI_TEST */
/* if (pAd->CommonCfg.bWiFiTest == FALSE) */
/* for SmartBit 64-byte stream test */
/* removed based on the decision of Ralink congress at 2011/7/06 */
/* if (pAd->MacTab.Size > 0) */
AsicAdjustTxPower(pAd);
/*#endif // WIFI_TEST */
/* BBP TUNING: dynamic tune BBP R66 to find a balance between sensibility
and noise isolation */
/* AsicBbpTuning2(pAd); */
/* walk through MAC table, see if switching TX rate is required */
/* MAC table maintenance */
if (pAd->Mlme.PeriodicRound % MLME_TASK_EXEC_MULTIPLE == 0)
{
/* one second timer */
MacTableMaintenance(pAd);
RTMPMaintainPMKIDCache(pAd);
#ifdef WDS_SUPPORT
WdsTableMaintenance(pAd);
#endif /* WDS_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabMaintain(pAd);
#endif /* CLIENT_WDS */
}
APUpdateCapabilityAndErpIe(pAd);
#ifdef APCLI_SUPPORT
if (pAd->Mlme.OneSecPeriodicRound % 2 == 0)
ApCliIfMonitor(pAd);
if (pAd->Mlme.OneSecPeriodicRound % 2 == 1)
ApCliIfUp(pAd);
{
INT loop;
ULONG Now32;
NdisGetSystemUpTime(&Now32);
for (loop = 0; loop < MAX_APCLI_NUM; loop++)
{
PAPCLI_STRUCT pApCliEntry = &pAd->ApCfg.ApCliTab[loop];
if ((pApCliEntry->Valid == TRUE)
&& (pApCliEntry->MacTabWCID < MAX_LEN_OF_MAC_TABLE))
{
/* update channel quality for Roaming and UI LinkQuality display */
MlmeCalculateChannelQuality(pAd,
&pAd->MacTab.Content[pApCliEntry->MacTabWCID], Now32);
}
}
}
#endif /* APCLI_SUPPORT */
#ifdef DOT11_N_SUPPORT
if (pAd->CommonCfg.bHTProtect)
{
/*APUpdateCapabilityAndErpIe(pAd); */
APUpdateOperationMode(pAd);
if (pAd->CommonCfg.IOTestParm.bRTSLongProtOn == FALSE)
{
AsicUpdateProtect(pAd, (USHORT)pAd->CommonCfg.AddHTInfo.AddHtInfo2.OperaionMode, ALLN_SETPROTECT, FALSE, pAd->MacTab.fAnyStationNonGF);
}
}
#endif /* DOT11_N_SUPPORT */
#ifdef A_BAND_SUPPORT
if ( (pAd->CommonCfg.Channel > 14)
&& (pAd->CommonCfg.bIEEE80211H == 1)
)
{
#ifdef DFS_SUPPORT
ApRadarDetectPeriodic(pAd);
#else
pAd->CommonCfg.InServiceMonitorCount++;
if (pAd->CommonCfg.RDMode == RD_SILENCE_MODE)
{
if (pAd->CommonCfg.RDCount++ > pAd->CommonCfg.ChMovingTime)
{
AsicEnableBssSync(pAd);
pAd->CommonCfg.RDMode = RD_NORMAL_MODE;
}
}
#endif /* DFS_SUPPORT */
}
#endif /* A_BAND_SUPPORT */
}
/*
==========================================================================
Description:
This routine is executed every second -
1. Decide the overall channel quality
2. Check if need to upgrade the TX rate to any client
3. perform MAC table maintenance, including ageout no-traffic clients,
and release packet buffer in PSQ is fail to TX in time.
==========================================================================
*/
VOID APMlmePeriodicExec(
PRTMP_ADAPTER pAd)
{
/*
Reqeust by David 2005/05/12
It make sense to disable Adjust Tx Power on AP mode, since we can't
take care all of the client's situation
ToDo: need to verify compatibility issue with WiFi product.
*/
#ifdef CARRIER_DETECTION_SUPPORT
if (isCarrierDetectExist(pAd) == TRUE)
{
PCARRIER_DETECTION_STRUCT pCarrierDetect = &pAd->CommonCfg.CarrierDetect;
if (pCarrierDetect->OneSecIntCount < pCarrierDetect->CarrierGoneThreshold)
{
pCarrierDetect->CD_State = CD_NORMAL;
pCarrierDetect->recheck = pCarrierDetect->recheck1;
if (pCarrierDetect->Debug != RT_DEBUG_TRACE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Carrier gone\n"));
/* start all TX actions. */
APMakeAllBssBeacon(pAd);
APUpdateAllBeaconFrame(pAd);
AsicEnableBssSync(pAd);
}
else
{
DBGPRINT(RT_DEBUG_TRACE, ("Carrier gone\n"));
}
}
pCarrierDetect->OneSecIntCount = 0;
}
#endif /* CARRIER_DETECTION_SUPPORT */
RTMP_CHIP_HIGH_POWER_TUNING(pAd, &pAd->ApCfg.RssiSample);
/* Disable Adjust Tx Power for WPA WiFi-test. */
/* Because high TX power results in the abnormal disconnection of Intel BG-STA. */
/*#ifndef WIFI_TEST */
/* if (pAd->CommonCfg.bWiFiTest == FALSE) */
/* for SmartBit 64-byte stream test */
/* removed based on the decision of Ralink congress at 2011/7/06 */
/* if (pAd->MacTab.Size > 0) */
#ifdef RT6352
if (IS_RT6352(pAd))
RT6352_AsicAdjustTxPower(pAd);
else
#endif /* RT6352 */
AsicAdjustTxPower(pAd);
/*#endif // WIFI_TEST */
#ifdef THERMAL_PROTECT_SUPPORT
thermal_protection(pAd);
#endif /* THERMAL_PROTECT_SUPPORT */
RTMP_CHIP_ASIC_TEMPERATURE_COMPENSATION(pAd);
/* walk through MAC table, see if switching TX rate is required */
/* MAC table maintenance */
if (pAd->Mlme.PeriodicRound % MLME_TASK_EXEC_MULTIPLE == 0)
{
/* one second timer */
MacTableMaintenance(pAd);
#ifdef CONFIG_FPGA_MODE
if (pAd->fpga_ctl.fpga_tr_stop)
{
UINT32 mac_val;
/* enable/disable tx/rx*/
RTMP_IO_READ32(pAd, MAC_SYS_CTRL, &mac_val);
switch (pAd->fpga_ctl.fpga_tr_stop)
{
case 3: //stop tx + rx
mac_val &= (~0xc);
break;
case 2: // stop rx
mac_val &= (~0x8);
break;
case 1: // stop tx
mac_val &= (~0x4);
break;
case 4:
default:
mac_val |= 0x0c;
break;
}
RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, mac_val);
}
#endif /* CONFIG_FPGA_MODE */
RTMPMaintainPMKIDCache(pAd);
#ifdef WDS_SUPPORT
WdsTableMaintenance(pAd);
#endif /* WDS_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabMaintain(pAd);
#endif /* CLIENT_WDS */
}
#ifdef AP_SCAN_SUPPORT
AutoChannelSelCheck(pAd);
#endif /* AP_SCAN_SUPPORT */
APUpdateCapabilityAndErpIe(pAd);
#ifdef APCLI_SUPPORT
if (pAd->Mlme.OneSecPeriodicRound % 2 == 0)
ApCliIfMonitor(pAd);
if (pAd->Mlme.OneSecPeriodicRound % 2 == 1)
#ifdef APCLI_AUTO_CONNECT_SUPPORT
if (pAd->ApCfg.ApCliAutoConnectChannelSwitching == FALSE)
#endif /* APCLI_AUTO_CONNECT_SUPPORT */
ApCliIfUp(pAd);
{
INT loop;
ULONG Now32;
#ifdef APCLI_CERT_SUPPORT
BOOLEAN IsUseBA = TRUE;
#endif /* APCLI_CERT_SUPPORT */
#ifdef MAC_REPEATER_SUPPORT
if (pAd->ApCfg.bMACRepeaterEn == TRUE)
{
#ifdef APCLI_AUTO_CONNECT_SUPPORT
RTMPRepeaterReconnectionCheck(pAd);
#endif /* APCLI_AUTO_CONNECT_SUPPORT */
}
#endif /* MAC_REPEATER_SUPPORT */
NdisGetSystemUpTime(&Now32);
for (loop = 0; loop < MAX_APCLI_NUM; loop++)
{
PAPCLI_STRUCT pApCliEntry = &pAd->ApCfg.ApCliTab[loop];
if (pAd->ApCfg.ApCliTab[loop].bBlockAssoc ==TRUE && pAd->ApCfg.ApCliTab[loop].bBlockAssoc &&
RTMP_TIME_AFTER(Now32, pAd->ApCfg.ApCliTab[loop].LastMicErrorTime + (60*OS_HZ)))
pAd->ApCfg.ApCliTab[loop].bBlockAssoc = FALSE;
if ((pApCliEntry->Valid == TRUE)
&& (pApCliEntry->MacTabWCID < MAX_LEN_OF_MAC_TABLE))
{
/* update channel quality for Roaming and UI LinkQuality display */
MlmeCalculateChannelQuality(pAd,
&pAd->MacTab.Content[pApCliEntry->MacTabWCID], Now32);
/* WPA MIC error should block association attempt for 60 seconds*/
#ifdef APCLI_CERT_SUPPORT
if (pAd->bApCliCertTest == TRUE)
{
PMAC_TABLE_ENTRY pEntry = &pAd->MacTab.Content[pApCliEntry->MacTabWCID];
struct wifi_dev *wdev = NULL;
wdev = &pApCliEntry->wdev;
if (pEntry->RXBAbitmap == 0 && pEntry->TXBAbitmap == 0)
IsUseBA = FALSE;
if( wdev->DesiredHtPhyInfo.bHtEnable &&
IsUseBA == FALSE )
{
EDCA_AC_CFG_STRUC Ac2Cfg, Ac1Cfg;
RTMP_IO_READ32(pAd, EDCA_AC2_CFG, &Ac2Cfg.word);
RTMP_IO_READ32(pAd, EDCA_AC1_CFG, &Ac1Cfg.word);
if ((pAd->RalinkCounters.OneSecOsTxCount[QID_AC_VO] == 0) &&
(pAd->RalinkCounters.OneSecOsTxCount[QID_AC_BK] >= 1000) &&
(pAd->RalinkCounters.OneSecOsTxCount[QID_AC_VI] == 0))
{
/*5.2.27 T7 */
if (Ac1Cfg.field.Aifsn!=0x1)
{
Ac1Cfg.field.Aifsn = 0x1;
RTMP_IO_WRITE32(pAd, EDCA_AC1_CFG, Ac1Cfg.word);
printk("Change EDCA_AC1_CFG to %x \n", Ac1Cfg.word);
}
}
else if ((pAd->RalinkCounters.OneSecOsTxCount[QID_AC_VO] == 0) &&
(pAd->RalinkCounters.OneSecOsTxCount[QID_AC_BK] == 0) &&
(pAd->RalinkCounters.OneSecOsTxCount[QID_AC_VI] == 0) &&
(pAd->RalinkCounters.OneSecOsTxCount[QID_AC_BE] < 10))
{
/* restore default parameter of BK*/
if (Ac1Cfg.field.Aifsn!=0x7)
{
Ac1Cfg.field.Aifsn = 0x7;
RTMP_IO_WRITE32(pAd, EDCA_AC1_CFG, Ac1Cfg.word);
printk("Restore EDCA_AC1_CFG to %x \n", Ac1Cfg.word);
}
}
pAd->RalinkCounters.OneSecOsTxCount[QID_AC_BE] = 0;
pAd->RalinkCounters.OneSecOsTxCount[QID_AC_BK] = 0;
pAd->RalinkCounters.OneSecOsTxCount[QID_AC_VI] = 0;
pAd->RalinkCounters.OneSecOsTxCount[QID_AC_VO] = 0;
}
}
#endif /* APCLI_CERT_SUPPORT */
}
}
}
#endif /* APCLI_SUPPORT */
#ifdef DOT11_N_SUPPORT
if (pAd->CommonCfg.bHTProtect)
{
/*APUpdateCapabilityAndErpIe(pAd); */
APUpdateOperationMode(pAd);
if (pAd->CommonCfg.IOTestParm.bRTSLongProtOn == FALSE)
{
AsicUpdateProtect(pAd, (USHORT)pAd->CommonCfg.AddHTInfo.AddHtInfo2.OperaionMode, ALLN_SETPROTECT, FALSE, pAd->MacTab.fAnyStationNonGF);
}
}
#endif /* DOT11_N_SUPPORT */
#ifdef A_BAND_SUPPORT
if ( (pAd->CommonCfg.Channel > 14)
&& (pAd->CommonCfg.bIEEE80211H == 1)
)
{
#ifdef DFS_SUPPORT
ApRadarDetectPeriodic(pAd);
#else
pAd->Dot11_H.InServiceMonitorCount++;
if (pAd->Dot11_H.RDMode == RD_SILENCE_MODE)
{
if (pAd->Dot11_H.RDCount++ > pAd->Dot11_H.ChMovingTime)
{
AsicEnableBssSync(pAd);
pAd->Dot11_H.RDMode = RD_NORMAL_MODE;
}
}
#endif /* !DFS_SUPPORT */
}
#endif /* A_BAND_SUPPORT */
#ifdef APCLI_SUPPORT
#ifdef DOT11_N_SUPPORT
#ifdef DOT11N_DRAFT3
#ifdef APCLI_CERT_SUPPORT
/* Perform 20/40 BSS COEX scan every Dot11BssWidthTriggerScanInt */
if (APCLI_IF_UP_CHECK(pAd, 0) && (pAd->bApCliCertTest == TRUE))
{
if ((OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_SCAN_2040)) &&
(pAd->CommonCfg.Dot11BssWidthTriggerScanInt != 0) &&
((pAd->Mlme.OneSecPeriodicRound % pAd->CommonCfg.Dot11BssWidthTriggerScanInt) == (pAd->CommonCfg.Dot11BssWidthTriggerScanInt-1)))
{
DBGPRINT(RT_DEBUG_TRACE, ("MMCHK - LastOneSecTotalTxCount/LastOneSecRxOkDataCnt = %d/%d \n",
pAd->RalinkCounters.LastOneSecTotalTxCount,
pAd->RalinkCounters.LastOneSecRxOkDataCnt));
/* Check last scan time at least 30 seconds from now. */
/* Check traffic is less than about 1.5~2Mbps.*/
/* it might cause data lost if we enqueue scanning.*/
/* This criteria needs to be considered*/
if ((pAd->RalinkCounters.LastOneSecTotalTxCount < 70) && (pAd->RalinkCounters.LastOneSecRxOkDataCnt < 70)
/*&& ((pAd->StaCfg.LastScanTime + 10 * OS_HZ) < pAd->Mlme.Now32) */)
{
MLME_SCAN_REQ_STRUCT ScanReq;
/* Fill out stuff for scan request and kick to scan*/
ScanParmFill(pAd, &ScanReq, ZeroSsid, 0, BSS_ANY, SCAN_2040_BSS_COEXIST);
/* Before scan, reset trigger event table. */
TriEventInit(pAd);
MlmeEnqueue(pAd, AP_SYNC_STATE_MACHINE, APMT2_MLME_SCAN_REQ, sizeof(MLME_SCAN_REQ_STRUCT), &ScanReq, 0);
/* Set InfoReq = 1, So after scan , alwats sebd 20/40 Coexistence frame to AP*/
pAd->CommonCfg.BSSCoexist2040.field.InfoReq = 1;
RTMP_MLME_HANDLER(pAd);
}
DBGPRINT(RT_DEBUG_TRACE, (" LastOneSecTotalTxCount/LastOneSecRxOkDataCnt = %d/%d \n",
pAd->RalinkCounters.LastOneSecTotalTxCount,
pAd->RalinkCounters.LastOneSecRxOkDataCnt));
}
}
#endif /* APCLI_CERT_SUPPORT */
#endif /* DOT11N_DRAFT3 */
#endif /* DOT11_N_SUPPORT */
#endif /* APCLI_SUPPORT */
}