/**
* Set the requested temperature range for high and low alert signals
*
* @param hwmgr The address of the hardware manager.
* @param range Temperature range to be programmed for high and low alert signals
* @exception PP_Result_BadInput if the input data is not valid.
*/
static int smu7_thermal_set_temperature_range(struct pp_hwmgr *hwmgr,
uint32_t low_temp, uint32_t high_temp)
{
uint32_t low = SMU7_THERMAL_MINIMUM_ALERT_TEMP *
PP_TEMPERATURE_UNITS_PER_CENTIGRADES;
uint32_t high = SMU7_THERMAL_MAXIMUM_ALERT_TEMP *
PP_TEMPERATURE_UNITS_PER_CENTIGRADES;
if (low < low_temp)
low = low_temp;
if (high > high_temp)
high = high_temp;
if (low > high)
return -EINVAL;
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_THERMAL_INT, DIG_THERM_INTH,
(high / PP_TEMPERATURE_UNITS_PER_CENTIGRADES));
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_THERMAL_INT, DIG_THERM_INTL,
(low / PP_TEMPERATURE_UNITS_PER_CENTIGRADES));
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_THERMAL_CTRL, DIG_THERM_DPM,
(high / PP_TEMPERATURE_UNITS_PER_CENTIGRADES));
return 0;
}
/**
* Reset Fan Speed Control to default mode.
* @param hwmgr the address of the powerplay hardware manager.
* @exception Should always succeed.
*/
static int iceland_fan_ctrl_set_default_mode(struct pp_hwmgr *hwmgr)
{
if (!hwmgr->fan_ctrl_is_in_default_mode) {
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, FDO_PWM_MODE, hwmgr->fan_ctrl_default_mode);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, TMIN, hwmgr->tmin);
hwmgr->fan_ctrl_is_in_default_mode = true;
}
return 0;
}
/**
* Programs thermal controller one-time setting registers
*
* @param hwmgr The address of the hardware manager.
*/
static int iceland_thermal_initialize(struct pp_hwmgr *hwmgr)
{
if (0 != hwmgr->thermal_controller.fanInfo.ucTachometerPulsesPerRevolution)
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_TACH_CTRL, EDGE_PER_REV,
hwmgr->thermal_controller.fanInfo.ucTachometerPulsesPerRevolution - 1);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, TACH_PWM_RESP_RATE, 0x28);
return 0;
}
/**
* Set Fan Speed Control to static mode, so that the user can decide what speed to use.
* @param hwmgr the address of the powerplay hardware manager.
* mode the fan control mode, 0 default, 1 by percent, 5, by RPM
* @exception Should always succeed.
*/
int iceland_fan_ctrl_set_static_mode(struct pp_hwmgr *hwmgr, uint32_t mode)
{
if (hwmgr->fan_ctrl_is_in_default_mode) {
hwmgr->fan_ctrl_default_mode = PHM_READ_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, FDO_PWM_MODE);
hwmgr->tmin = PHM_READ_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, TMIN);
hwmgr->fan_ctrl_is_in_default_mode = false;
}
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, TMIN, 0);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL2, FDO_PWM_MODE, mode);
return 0;
}
/**
* Set Fan Speed in percent.
* @param hwmgr the address of the powerplay hardware manager.
* @param speed is the percentage value (0% - 100%) to be set.
* @exception Fails is the 100% setting appears to be 0.
*/
int smu7_fan_ctrl_set_fan_speed_percent(struct pp_hwmgr *hwmgr,
uint32_t speed)
{
uint32_t duty100;
uint32_t duty;
uint64_t tmp64;
if (hwmgr->thermal_controller.fanInfo.bNoFan)
return 0;
if (speed > 100)
speed = 100;
if (PP_CAP(PHM_PlatformCaps_MicrocodeFanControl))
smu7_fan_ctrl_stop_smc_fan_control(hwmgr);
duty100 = PHM_READ_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_FDO_CTRL1, FMAX_DUTY100);
if (duty100 == 0)
return -EINVAL;
tmp64 = (uint64_t)speed * duty100;
do_div(tmp64, 100);
duty = (uint32_t)tmp64;
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_FDO_CTRL0, FDO_STATIC_DUTY, duty);
return smu7_fan_ctrl_set_static_mode(hwmgr, FDO_PWM_MODE_STATIC);
}
/**
* Set Fan Speed in RPM.
* @param hwmgr the address of the powerplay hardware manager.
* @param speed is the percentage value (min - max) to be set.
* @exception Fails is the speed not lie between min and max.
*/
int polaris10_fan_ctrl_set_fan_speed_rpm(struct pp_hwmgr *hwmgr, uint32_t speed)
{
uint32_t tach_period;
uint32_t crystal_clock_freq;
if (hwmgr->thermal_controller.fanInfo.bNoFan ||
(hwmgr->thermal_controller.fanInfo.
ucTachometerPulsesPerRevolution == 0) ||
(speed < hwmgr->thermal_controller.fanInfo.ulMinRPM) ||
(speed > hwmgr->thermal_controller.fanInfo.ulMaxRPM))
return 0;
if (phm_cap_enabled(hwmgr->platform_descriptor.platformCaps,
PHM_PlatformCaps_MicrocodeFanControl))
polaris10_fan_ctrl_stop_smc_fan_control(hwmgr);
crystal_clock_freq = tonga_get_xclk(hwmgr);
tach_period = 60 * crystal_clock_freq * 10000 / (8 * speed);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_TACH_STATUS, TACH_PERIOD, tach_period);
return polaris10_fan_ctrl_set_static_mode(hwmgr, FDO_PWM_MODE_STATIC);
}
/**
* Set Fan Speed in percent.
* @param hwmgr the address of the powerplay hardware manager.
* @param speed is the percentage value (0% - 100%) to be set.
* @exception Fails is the 100% setting appears to be 0.
*/
int iceland_fan_ctrl_set_fan_speed_percent(struct pp_hwmgr *hwmgr, uint32_t speed)
{
uint32_t duty100;
uint32_t duty;
uint64_t tmp64;
if (hwmgr->thermal_controller.fanInfo.bNoFan)
return -EINVAL;
if (speed > 100) {
pr_warning("Cannot set more than 100%% duty cycle. Set it to 100.\n");
speed = 100;
}
if (phm_cap_enabled(hwmgr->platform_descriptor.platformCaps, PHM_PlatformCaps_MicrocodeFanControl))
iceland_fan_ctrl_stop_smc_fan_control(hwmgr);
duty100 = PHM_READ_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL1, FMAX_DUTY100);
if (0 == duty100)
return -EINVAL;
tmp64 = (uint64_t)speed * duty100;
do_div(tmp64, 100);
duty = (uint32_t)tmp64;
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_FDO_CTRL0, FDO_STATIC_DUTY, duty);
return iceland_fan_ctrl_set_static_mode(hwmgr, FDO_PWM_MODE_STATIC);
}
/**
* Disable thermal alerts on the RV770 thermal controller.
* @param hwmgr The address of the hardware manager.
*/
static int iceland_thermal_disable_alert(struct pp_hwmgr *hwmgr)
{
uint32_t alert;
alert = PHM_READ_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_THERMAL_INT, THERM_INT_MASK);
alert |= (ICELAND_THERMAL_HIGH_ALERT_MASK | ICELAND_THERMAL_LOW_ALERT_MASK);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, CG_THERMAL_INT, THERM_INT_MASK, alert);
/* send message to SMU to disable internal thermal interrupts */
return (smum_send_msg_to_smc(hwmgr->smumgr, PPSMC_MSG_Thermal_Cntl_Disable) == 0) ? 0 : -1;
}
/**
* Enable thermal alerts on the RV770 thermal controller.
*
* @param hwmgr The address of the hardware manager.
*/
static void smu7_thermal_enable_alert(struct pp_hwmgr *hwmgr)
{
uint32_t alert;
alert = PHM_READ_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_THERMAL_INT, THERM_INT_MASK);
alert &= ~(SMU7_THERMAL_HIGH_ALERT_MASK | SMU7_THERMAL_LOW_ALERT_MASK);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_THERMAL_INT, THERM_INT_MASK, alert);
/* send message to SMU to enable internal thermal interrupts */
smum_send_msg_to_smc(hwmgr, PPSMC_MSG_Thermal_Cntl_Enable);
}
/**
* Set Fan Speed in RPM.
* @param hwmgr the address of the powerplay hardware manager.
* @param speed is the percentage value (min - max) to be set.
* @exception Fails is the speed not lie between min and max.
*/
int smu7_fan_ctrl_set_fan_speed_rpm(struct pp_hwmgr *hwmgr, uint32_t speed)
{
uint32_t tach_period;
uint32_t crystal_clock_freq;
if (hwmgr->thermal_controller.fanInfo.bNoFan ||
(hwmgr->thermal_controller.fanInfo.
ucTachometerPulsesPerRevolution == 0) ||
(speed < hwmgr->thermal_controller.fanInfo.ulMinRPM) ||
(speed > hwmgr->thermal_controller.fanInfo.ulMaxRPM))
return 0;
if (PP_CAP(PHM_PlatformCaps_MicrocodeFanControl))
smu7_fan_ctrl_stop_smc_fan_control(hwmgr);
crystal_clock_freq = amdgpu_asic_get_xclk((struct amdgpu_device *)hwmgr->adev);
tach_period = 60 * crystal_clock_freq * 10000 / (8 * speed);
PHM_WRITE_VFPF_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
CG_TACH_STATUS, TACH_PERIOD, tach_period);
return smu7_fan_ctrl_set_static_mode(hwmgr, FDO_PWM_MODE_STATIC_RPM);
}
