void
HardwareSerial::primeTransmit(unsigned long ulBase)
{
//
// Do we have any data to transmit?
//
if(!TX_BUFFER_EMPTY)
{
//
// Disable the UART interrupt. If we don't do this there is a race
// condition which can cause the read index to be corrupted.
//
ROM_IntDisable(g_ulUARTInt[uartModule]);
//
// Yes - take some characters out of the transmit buffer and feed
// them to the UART transmit FIFO.
//
while(!TX_BUFFER_EMPTY)
{
while(ROM_UARTSpaceAvail(ulBase) && !TX_BUFFER_EMPTY) {
ROM_UARTCharPutNonBlocking(ulBase,
txBuffer[txReadIndex]);
txReadIndex = (txReadIndex + 1) % SERIAL_BUFFER_SIZE;
}
}
//
// Reenable the UART interrupt.
//
ROM_IntEnable(g_ulUARTInt[uartModule]);
}
}
//*****************************************************************************
// UART interrupt handler.
//*****************************************************************************
void UART0_IntHandler(void)
{
uint32_t status = ROM_UARTIntStatus(UART0_BASE, true);
ROM_UARTIntClear(UART0_BASE, status);
// drain rx FIFO
while(ROM_UARTCharsAvail(UART0_BASE))
{
char ch = ROM_UARTCharGetNonBlocking(UART0_BASE);
if(inputRB.nbytes < DBG_IN_BUFFER_SIZE)
{
RB_Push(dbg_inputBuffer, inputRB, ch, DBG_IN_BUFFER_SIZE);
if(ch == '\r')
++newlines;
}
else
{
// Attempt to report overflow and clear buffer
// Must do this to avoid condition where buffer is full and code
// is waiting for a newline that can not fit in the buffer.
dbg_putstr_nb("\rRXOVF\r\n");
RB_Clear(inputRB);
newlines = 0;
}
}
// feed tx FIFO
// Echo received characters
while(ROM_UARTSpaceAvail(UART0_BASE) && echoPtr != inputRB.wp)
{
ROM_UARTCharPutNonBlocking(UART0_BASE, dbg_inputBuffer[echoPtr]);
echoPtr = (echoPtr + 1) % DBG_IN_BUFFER_SIZE;
}
// Write pending characters
while(ROM_UARTSpaceAvail(UART0_BASE) && outputRB.nbytes > 0)
{
ROM_UARTCharPutNonBlocking(UART0_BASE, RB_Front(dbg_outputBuffer, outputRB));
RB_Pop(outputRB, DBG_OUT_BUFFER_SIZE);
}
} // UART0_IntHandler()
int dbg_putc_nb(char ch, void * userdata)
{
if(ROM_UARTSpaceAvail(UART0_BASE) && outputRB.nbytes == 0)
{
ROM_UARTCharPutNonBlocking(UART0_BASE, ch);
}
else
{
if(!RB_Full(outputRB, DBG_OUT_BUFFER_SIZE))
RB_Push(dbg_outputBuffer, outputRB, ch, DBG_OUT_BUFFER_SIZE);
}
return 0;
}
//*****************************************************************************
//
// Take as many bytes from the transmit buffer as we have space for and move
// them into the USB UART's transmit FIFO.
//
//*****************************************************************************
static void
USBUARTPrimeTransmit(uint32_t ui32Base)
{
uint32_t ui32Read;
uint8_t ui8Char;
//
// If we are currently sending a break condition, don't receive any
// more data. We will resume transmission once the break is turned off.
//
if(g_bSendingBreak)
{
return;
}
//
// If there is space in the UART FIFO, try to read some characters
// from the receive buffer to fill it again.
//
while(ROM_UARTSpaceAvail(ui32Base))
{
//
// Get a character from the buffer.
//
ui32Read = USBBufferRead((tUSBBuffer *)&g_sRxBuffer, &ui8Char, 1);
//
// Did we get a character?
//
if(ui32Read)
{
//
// Place the character in the UART transmit FIFO.
//
ROM_UARTCharPutNonBlocking(ui32Base, ui8Char);
//
// Update our count of bytes transmitted via the UART.
//
g_ui32UARTTxCount++;
}
else
{
//
// We ran out of characters so exit the function.
//
return;
}
}
}
//*****************************************************************************
//
// Take as many bytes from the transmit buffer as there is space for and move
// them into the USB UART's transmit FIFO.
//
//*****************************************************************************
static void
USBUARTPrimeTransmit(void)
{
unsigned long ulRead;
unsigned char ucChar;
//
// If a break condition is currently being sent, don't receive any more
// data. Transmission will resume once the break is turned off.
//
if(g_bSendingBreak)
{
return;
}
//
// If there is space in the UART FIFO, try to read some characters
// from the receive buffer to fill it again.
//
while(ROM_UARTSpaceAvail(UART0_BASE))
{
//
// Get a character from the buffer.
//
ulRead = USBBufferRead(&g_sRxBuffer, &ucChar, 1);
//
// Was a character read?
//
if(ulRead)
{
//
// Place the character in the UART transmit FIFO.
//
ROM_UARTCharPutNonBlocking(UART0_BASE, ucChar);
}
else
{
//
// There are no more characters so exit the function.
//
return;
}
}
}
//*****************************************************************************
//
// Handles interrupts from the UART.
//
//*****************************************************************************
void
UART0IntHandler(void)
{
unsigned long ulStatus;
unsigned char ucChar;
//
// Get the interrupts that are being asserted by the UART.
//
ulStatus = ROM_UARTIntStatus(UART0_BASE, true);
//
// Clear the asserted interrupts.
//
ROM_UARTIntClear(UART0_BASE, ulStatus);
//
// Indicate that the UART link is good.
//
ControllerLinkGood(LINK_TYPE_UART);
//
// See if the receive interrupt has been asserted.
//
if(ulStatus & (UART_INT_RX | UART_INT_RT))
{
//
// Loop while there are more characters to be read from the UART.
//
while(ROM_UARTCharsAvail(UART0_BASE))
{
//
// Read the next character from the UART.
//
ucChar = ROM_UARTCharGet(UART0_BASE);
//
// See if this is a start of packet byte.
//
if(ucChar == 0xff)
{
//
// Reset the length of the UART message.
//
g_ulUARTLength = 0;
//
// Set the state such that the next byte received is the size
// of the message.
//
g_ulUARTState = UART_STATE_LENGTH;
}
//
// See if this byte is the size of the message.
//
else if(g_ulUARTState == UART_STATE_LENGTH)
{
//
// Save the size of the message.
//
g_ulUARTSize = ucChar;
//
// Subsequent bytes received are the message data.
//
g_ulUARTState = UART_STATE_DATA;
}
//
// See if the previous character was an escape character.
//
else if(g_ulUARTState == UART_STATE_ESCAPE)
{
//
// See if this 0xfe, the escaped version of 0xff.
//
if(ucChar == 0xfe)
{
//
// Store a 0xff in the message buffer.
//
g_pucUARTMessage[g_ulUARTLength++] = 0xff;
//
// Subsequent bytes received are the message data.
//
g_ulUARTState = UART_STATE_DATA;
}
//
// Otherwise, see if this is 0xfd, the escaped version of 0xfe.
//
else if(ucChar == 0xfd)
{
//
// Store a 0xfe in the message buffer.
//
g_pucUARTMessage[g_ulUARTLength++] = 0xfe;
//
// Subsequent bytes received are the message data.
//
g_ulUARTState = UART_STATE_DATA;
}
//
// Otherwise, this is a corrupted sequence. Set the receiver
// to idle so this message is dropped, and subsequent data is
// ignored until another start of packet is received.
//
else
{
g_ulUARTState = UART_STATE_IDLE;
}
}
//
// See if this is a part of the message data.
//
else if(g_ulUARTState == UART_STATE_DATA)
{
//
// See if this character is an escape character.
//
if(ucChar == 0xfe)
{
//
// The next byte is an escaped byte.
//
g_ulUARTState = UART_STATE_ESCAPE;
}
else
{
//
// Store this byte in the message buffer.
//
g_pucUARTMessage[g_ulUARTLength++] = ucChar;
}
}
//
// See if the entire message has been received but has not been
// processed (i.e. the most recent byte received was the end of the
// message).
//
if((g_ulUARTLength == g_ulUARTSize) &&
(g_ulUARTState == UART_STATE_DATA))
{
//
// Process this message.
//
UARTIFCommandHandler();
//
// The UART interface is idle, meaning all bytes will be
// dropped until the next start of packet byte.
//
g_ulUARTState = UART_STATE_IDLE;
}
}
//
// Tell the controller that CAN activity was detected.
//
ControllerWatchdog(LINK_TYPE_UART);
}
//
// See if the transmit interrupt has been asserted.
//
if(ulStatus & UART_INT_TX)
{
//
// Loop while there are more characters to be transmitted and more
// space in the UART FIFO.
//
while((g_ulUARTXmitRead != g_ulUARTXmitWrite) &&
ROM_UARTSpaceAvail(UART0_BASE))
{
//
// Put the next character into the UART FIFO.
//
ROM_UARTCharPut(UART0_BASE, g_pucUARTXmit[g_ulUARTXmitRead]);
//
// Increment the read pointer.
//
g_ulUARTXmitRead = (g_ulUARTXmitRead + 1) % UART_XMIT_SIZE;
}
}
//
// See if an enumeration response needs to be sent.
//
if(HWREGBITW(&g_ulUARTFlags, UART_FLAG_ENUM) != 0)
{
//
// Send the enumeration response for this device.
//
UARTIFSendMessage(CAN_MSGID_API_ENUMERATE |
g_sParameters.ucDeviceNumber, 0, 0);
//
// Clear the enumeration response flag.
//
HWREGBITW(&g_ulUARTFlags, UART_FLAG_ENUM) = 0;
}
//
// See if periodic status messages need to be sent.
//
if(HWREGBITW(&g_ulUARTFlags, UART_FLAG_PSTATUS) != 0)
{
//
// Send out the first periodic status message if it needs to be sent.
//
if(g_ulPStatFlags & 1)
{
UARTIFSendMessage(LM_API_PSTAT_DATA_S0 |
g_sParameters.ucDeviceNumber,
g_ppucPStatMessages[0],
g_pucPStatMessageLen[0]);
}
//
// Send out the second periodic status message if it needs to be sent.
//
if(g_ulPStatFlags & 2)
{
UARTIFSendMessage(LM_API_PSTAT_DATA_S1 |
g_sParameters.ucDeviceNumber,
g_ppucPStatMessages[1],
g_pucPStatMessageLen[1]);
}
//
// Send out the third periodic status message if it needs to be sent.
//
if(g_ulPStatFlags & 4)
{
UARTIFSendMessage(LM_API_PSTAT_DATA_S2 |
g_sParameters.ucDeviceNumber,
g_ppucPStatMessages[2],
g_pucPStatMessageLen[2]);
}
//
// Send out the fourth periodic status message if it needs to be sent.
//
if(g_ulPStatFlags & 8)
{
UARTIFSendMessage(LM_API_PSTAT_DATA_S3 |
g_sParameters.ucDeviceNumber,
g_ppucPStatMessages[3],
g_pucPStatMessageLen[3]);
}
//
// Clear the periodic status message flag.
//
HWREGBITW(&g_ulUARTFlags, UART_FLAG_PSTATUS) = 0;
}
}
//*****************************************************************************
//
// Sends a character to the UART.
//
//*****************************************************************************
static void
UARTIFPutChar(unsigned long ulChar)
{
//
// See if the character being sent is 0xff.
//
if(ulChar == 0xff)
{
//
// Send 0xfe 0xfe, the escaped version of 0xff. A sign extended
// version of 0xfe is used to avoid the check below for 0xfe, thereby
// avoiding an infinite loop. Only the lower 8 bits are actually sent,
// so 0xfe is what is actually transmitted.
//
UARTIFPutChar(0xfffffffe);
UARTIFPutChar(0xfffffffe);
}
//
// Otherwise, see if the character being sent is 0xfe.
//
else if(ulChar == 0xfe)
{
//
// Send 0xfe 0xfd, the escaped version of 0xfe. A sign extended
// version of 0xfe is used to avoid the check above for 0xfe, thereby
// avoiding an infinite loop. Only the lower 8 bits are actually sent,
// so 0xfe is what is actually transmitted.
//
UARTIFPutChar(0xfffffffe);
UARTIFPutChar(0xfd);
}
//
// Otherwise, simply send this character.
//
else
{
//
// Disable the UART interrupt to avoid having characters stick in the
// local buffer.
//
ROM_UARTIntDisable(UART0_BASE, UART_INT_TX);
//
// See if the local buffer is empty and there is space available in the
// UART FIFO.
//
if((g_ulUARTXmitRead == g_ulUARTXmitWrite) &&
ROM_UARTSpaceAvail(UART0_BASE))
{
//
// Simply write this character into the UART FIFO.
//
ROM_UARTCharPut(UART0_BASE, ulChar);
}
else
{
//
// Write this character into the local buffer.
//
g_pucUARTXmit[g_ulUARTXmitWrite] = ulChar;
//
// Increment the local write buffer pointer.
//
g_ulUARTXmitWrite = (g_ulUARTXmitWrite + 1) % UART_XMIT_SIZE;
}
//
// Re-enable the UART interrupt.
//
ROM_UARTIntEnable(UART0_BASE, UART_INT_TX);
}
}