Exemplos de SpiDeInit em C++ (Cpp)

Exemplo n.º 1

Arquivo: board.c Projeto: AlessandroLipari/LoRaMac-node

void BoardDeInitMcu( void )
{
    Gpio_t oscHseIn;
    Gpio_t oscHseOut;  
    Gpio_t oscLseIn;
    Gpio_t oscLseOut;

    I2cDeInit( &I2c );
    SpiDeInit( &SX1272.Spi );
    SX1272IoDeInit( );

#if defined( USE_DEBUG_PINS )
    GpioInit( &DbgPin1, CON_EXT_1, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &DbgPin2, CON_EXT_3, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &DbgPin3, CON_EXT_7, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &DbgPin4, CON_EXT_9, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
#endif

    GpioInit( &oscHseIn, OSC_HSE_IN, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &oscHseOut, OSC_HSE_OUT, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );

    GpioInit( &oscLseIn, OSC_LSE_IN, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
    GpioInit( &oscLseOut, OSC_LSE_OUT, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
    
    McuInitialized = false;
}

Exemplo n.º 2

Arquivo: board.c Projeto: czj-tyro/LoRaMac-node

void BoardDeInitMcu( void )
{
    I2cDeInit( &I2c );
    AdcDeInit( &Adc );

    SpiDeInit( &SX1272.Spi );
    SX1272IoDeInit( );
}

Exemplo n.º 3

Arquivo: board.c Projeto: AlexanderWiniger/LoRaMac-node

void BoardDeInitMcu( void )
{
#if defined(SX1276_BOARD_EMBED)
    SpiDeInit(&SX1276.Spi);
    SX1276IoDeInit();
#endif

    McuInitialized = false;
}

Exemplo n.º 4

Arquivo: board.c Projeto: AnselZhangGit/LoRaMac-node

void BoardDeInitMcu( void )
{
    Gpio_t ioPin;

    SpiDeInit( &SX1272.Spi );
    SX1272IoDeInit( );

    GpioInit( &ioPin, OSC_HSE_IN, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &ioPin, OSC_HSE_OUT, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );

    GpioInit( &ioPin, OSC_LSE_IN, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
    GpioInit( &ioPin, OSC_LSE_OUT, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
}

Exemplo n.º 5

Arquivo: hw_net.c Projeto: brandondoran/t1-firmware

void hw_net_disable (void)
{
	CC3000_START;
	wlan_stop();
	SpiDeInit();
	// clear out all wifi data
	memset(hw_wifi_ip, 0, sizeof hw_wifi_ip);
	memset(hw_wifi_ip, 0, sizeof hw_cc_ver);
	// reset connection
	ulCC3000Connected = 0;
	ulCC3000DHCP = 0;
	hw_digital_write(CC3K_CONN_LED, 0);
	hw_digital_write(CC3K_ERR_LED, 0);
	CC3000_END;
}

Exemplo n.º 6

Arquivo: board.c Projeto: juliocdep/contiki

void BoardDeInitMcu( void )
{
    Gpio_t ioPin;

    I2cDeInit( &I2c );
    SpiDeInit( &SX1276.Spi );
    SX1276IoDeInit( );

    LedDeInit();

    /*GpioInit( &Led1, LED_1, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &Led2, LED_2, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &Led3, LED_3, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &Led4, LED_4, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );*/

    /*Led3Status = GpioRead( &Led3 );
    if( Led3Status == 1 )
    {
        GpioInit( &Led3, LED_3, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    }*/

    /*GpioInit( &Sel1, SEL_1, PIN_OUTPUT, PIN_OPEN_DRAIN, PIN_NO_PULL, 0 );
    GpioInit( &Sel2, SEL_2, PIN_OUTPUT, PIN_OPEN_DRAIN, PIN_NO_PULL, 0 );
    GpioInit( &Sel3, SEL_3, PIN_OUTPUT, PIN_OPEN_DRAIN, PIN_NO_PULL, 0 );
    GpioInit( &Sel4, SEL_4, PIN_OUTPUT, PIN_OPEN_DRAIN, PIN_NO_PULL, 0 );*/

#if ( defined( USE_DEBUG_PINS ) && !defined( LOW_POWER_MODE_ENABLE ) )
    GpioInit( &DbgPin1, J1_1, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &DbgPin2, J1_2, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &DbgPin3, J1_3, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &DbgPin4, J1_4, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
#endif

    /*GpioInit( &ioPin, OSC_HSE_IN, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &ioPin, OSC_HSE_OUT, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );

    GpioInit( &ioPin, OSC_LSE_IN, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
    GpioInit( &ioPin, OSC_LSE_OUT, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );*/
    
    McuInitialized = false;
}

Exemplo n.º 7

Arquivo: board.c Projeto: AlessandroLipari/LoRaMac-node

void BoardDeInitMcu( void )
{
    Gpio_t oscHseIn;
    Gpio_t oscHseOut;  
    Gpio_t oscLseIn;
    Gpio_t oscLseOut;

    I2cDeInit( &I2c );
    SpiDeInit( &SX1276.Spi );
    SX1276IoDeInit( );

    GpioInit( &oscHseIn, OSC_HSE_IN, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &oscHseOut, OSC_HSE_OUT, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );

    GpioInit( &oscLseIn, OSC_LSE_IN, PIN_INPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    GpioInit( &oscLseOut, OSC_LSE_OUT, PIN_INPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
    
    GpioInit( &UsbDetect, USB_ON, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
	
    McuInitialized = false;
}

Exemplo n.º 8

Arquivo: board.c Projeto: hollie/LoRaMac-node

void BoardDeInitMcu( void )
{
	/* Switching the CPU clock source to HFRCO */
	CMU_ClockSelectSet(cmuClock_HF, cmuSelect_HFRCO);

	/* Disabling every oscillator except hfrco and lfxo */
	CMU_OscillatorEnable(cmuOsc_AUXHFRCO, false, true);
	CMU_OscillatorEnable(cmuOsc_HFXO, false, true);
	CMU_OscillatorEnable(cmuOsc_LFRCO, false, true);

#ifdef USE_I2C
	I2cDeInit( &I2c );
#endif

	SpiDeInit( &SX1272.Spi );
	SX1272IoDeInit( );

	GpioInit( &Led1, LED_1, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
	GpioInit( &Led2, LED_2, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
	McuInitialized = false;
}

Exemplo n.º 9

Arquivo: board.c Projeto: XueZhiQiang123/FloRa

void BoardDeInitMcu( void )
{
    Gpio_t ioPin;

    //I2cDeInit( &I2c );
    SpiDeInit( &SX1272.Spi );
    SX1272IoDeInit( );

//#if ( defined( USE_DEBUG_PINS ) && !defined( LOW_POWER_MODE_ENABLE ) )
//    GpioInit( &DbgPin1, CON_EXT_1, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
//    GpioInit( &DbgPin2, CON_EXT_3, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
//    GpioInit( &DbgPin3, CON_EXT_7, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
//    GpioInit( &DbgPin4, CON_EXT_9, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
//#endif
		GpioInit( &ioPin, OSC_HSE_IN, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
    GpioInit( &ioPin, OSC_HSE_OUT, PIN_ANALOGIC, PIN_PUSH_PULL, PIN_NO_PULL, 1 );

    GpioInit( &ioPin, OSC_LSE_IN, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
    GpioInit( &ioPin, OSC_LSE_OUT, PIN_INPUT, PIN_PUSH_PULL, PIN_PULL_DOWN, 1 );
    
    McuInitialized = false;
}