void Config()
{
//System clock at power up is HSI/8 = 16MHz/8 = 2MHz
//CLK_SYSCLKDivConfig(CLK_SYSCLKDiv_1); //set HSI/4 = 4MHz SysClk to Core and Memory, minimum clock = 125KHz for CLK_SYSCLKDiv_128
//PWR_PVDCmd(ENABLE); //Power voltage detector and brownout Reset unit supply current 2,6uA
//PWR_PVDLevelConfig(PWR_PVDLevel_2V26); //set Programmable voltage detector threshold to 2,26V
//PWR_GetFlagStatus(PWR_FLAG_PVDOF); //checks whether the specified PWR flag is set or not
//Configure external interrupts - BTN1 and BTN2 presses
EXTI_SetPinSensitivity(EXTI_Pin_0, EXTI_Trigger_Falling_Low);
//EXTI_SetPinSensitivity(EXTI_Pin_4, EXTI_Trigger_Falling_Low);
//EXTI_SelectPort(EXTI_Port_B);
//EXTI_SetHalfPortSelection(EXTI_HalfPort_B_MSB, ENABLE);
/* Input FL IT - onboard Button, external pull-up */
GPIO_Init(BTN1_PORT, BTN1_PIN, GPIO_Mode_In_FL_IT);
GPIO_Init(BTN2_PORT, BTN2_PIN, GPIO_Mode_In_FL_IT);
// Timer 3 Configuration
CLK_PeripheralClockConfig(CLK_Peripheral_TIM3, ENABLE);
TIM3_TimeBaseInit(TIM3_Prescaler_2, TIM3_CounterMode_Up, 700); // 1MHz timer clock
TIM3_OC1Init(TIM3_OCMode_PWM1,
TIM3_OutputState_Enable,
350,
TIM3_OCPolarity_Low,
TIM3_OCIdleState_Reset);
TIM3_ARRPreloadConfig(ENABLE);
TIM3_OC1PreloadConfig(ENABLE);
TIM3_CtrlPWMOutputs(ENABLE);
TIM3_Cmd(DISABLE);
/* RFM85W pins */
GPIO_Init(RFM_DATA_PORT, RFM_DATA_PIN, GPIO_Mode_Out_PP_Low_Fast);
GPIO_Init(RFM_ON_PORT, RFM_ON_PIN, GPIO_Mode_Out_PP_Low_Fast);
/* Output PP High - bicolor LED to GND */
GPIO_Init(LED_PORT, LED_PIN1, GPIO_Mode_Out_PP_Low_Slow);
GPIO_Init(LED_PORT, LED_PIN2, GPIO_Mode_Out_PP_Low_Slow);
RFM_OFF;
//RFM_DATA(0);
}
/**
* @brief Configure TIM1,2,3 peripherals
* @param None
* @retval None
*/
static void TIM_Config(void)
{
/* TIM1 configuration:
- TIM1CLK is set to 2 MHz, the TIM2 Prescaler is equal to 15 so the TIM1 counter
clock used is 2 MHz / (15 + 1) = 125 000 Hz
- TIM1 Channel 1 output frequency = TIM1CLK / (TIM1_PERIOD + 1) * (TIM1_PRESCALER + 1)
= 2 000 000 / 256 * 16 = 488.28 Hz */
/* Time Base configuration */
TIM1_TimeBaseInit(TIM1_PRESCALER, TIM1_CounterMode_Up, TIM1_PERIOD, TIM1_REPETITION_COUNTER);
/* TIM1 Channel 1 Configuration in PWM2 mode */
TIM1_OC1Init(TIM1_OCMode_PWM2, TIM1_OutputState_Enable, TIM1_OutputNState_Disable, TIM1_CCR1_VAL,
TIM1_OCPolarity_Low, TIM1_OCNPolarity_Low, TIM1_OCIdleState_Set, TIM1_OCNIdleState_Set);
/* Master Mode selection: Update event */
TIM1_SelectOutputTrigger(TIM1_TRGOSource_Update);
/* TIM2 configuration:
- TIM2 is connected to TIM1 Update so TIM2CLK is equal to
TIM1 output clock / (TIM1_REPETITION_COUNTER + 1) = 488.28 / 5 = 97.65 Hz
- TIM2 Prescaler is equal to 1 so the TIM2 counter clock used is 97.65 / 1 = 97.65 Hz
- TIM2 Channel 1 output frequency = TIM2CLK / (TIM2_PERIOD + 1) * TIM2_Prescaler
= 97.65 / 3 * 1 = 32.55 Hz */
/* Time Base configuration */
TIM2_TimeBaseInit(TIM2_Prescaler_1, TIM2_CounterMode_Up, TIM2_PERIOD);
TIM2_OC1Init(TIM2_OCMode_PWM2, TIM2_OutputState_Enable, TIM2_CCR1_VAL,
TIM2_OCPolarity_Low, TIM2_OCIdleState_Reset);
/* TIM2 Slave Mode selection: Gated mode */
TIM2_SelectSlaveMode(TIM2_SlaveMode_Gated);
TIM2_SelectInputTrigger(TIM2_TRGSelection_TIM1);
/* TIM3 configuration:
- TIM3 is connected to TIM1 Update so TIM3CLK is equal to
TIM1 output clock / (TIM1_REPETITION_COUNTER + 1) = 488.28 / 5 = 97.65 Hz
- TIM3 Prescaler is equal to 1 so the TIM3 counter clock used is 97.65 / 1 = 97.65 Hz
- TIM3 Channel 1 output frequency = TIM3CLK / (TIM3_PERIOD + 1) * TIM3Prescaler
= 97.65 / 4 * 1 = 24.41 Hz */
/* Time Base configuration */
TIM3_TimeBaseInit(TIM3_Prescaler_1, TIM3_CounterMode_Up, TIM3_PERIOD);
TIM3_OC1Init(TIM3_OCMode_PWM2, TIM3_OutputState_Enable, TIM3_CCR1_VAL,
TIM3_OCPolarity_Low, TIM3_OCIdleState_Reset);
/* TIM3 Slave Mode selection: Gated mode */
TIM3_SelectSlaveMode(TIM3_SlaveMode_Gated);
TIM3_SelectInputTrigger(TIM3_TRGSelection_TIM1);
/* Main Output Enable */
TIM1_CtrlPWMOutputs(ENABLE);
TIM2_CtrlPWMOutputs(ENABLE);
TIM3_CtrlPWMOutputs(ENABLE);
/* TIM2 counter enable */
TIM2_Cmd(ENABLE);
/* TIM3 counter enable */
TIM3_Cmd(ENABLE);
/* TIM1 counter enable */
TIM1_Cmd(ENABLE);
}