/*******************************************************************************
* Function Name: UART_1_SpiUartClearRxBuffer
****************************************************************************//**
*
* Clears the receive buffer and RX FIFO.
*
* \globalvars
* UART_1_rxBufferHead - the start index to put data into the
* software receive buffer.
* UART_1_rxBufferTail - the start index to get data from the
* software receive buffer.
*
*******************************************************************************/
void UART_1_SpiUartClearRxBuffer(void)
{
#if (UART_1_CHECK_RX_SW_BUFFER)
{
/* Lock from component interruption */
UART_1_DisableInt();
/* Flush RX software buffer */
UART_1_rxBufferHead = UART_1_rxBufferTail;
UART_1_rxBufferOverflow = 0u;
UART_1_CLEAR_RX_FIFO;
UART_1_ClearRxInterruptSource(UART_1_INTR_RX_ALL);
#if (UART_1_CHECK_UART_RTS_CONTROL_FLOW)
{
/* Enable RX Not Empty interrupt source to continue receiving
* data into software buffer.
*/
UART_1_INTR_RX_MASK_REG |= UART_1_INTR_RX_NOT_EMPTY;
}
#endif
/* Release lock */
UART_1_EnableInt();
}
#else
{
UART_1_CLEAR_RX_FIFO;
}
#endif
}
/*******************************************************************************
* Function Name: UART_1_UartGetByte
********************************************************************************
*
* Summary:
* Retrieves the next data element from the receive buffer, returns the
* received byte and error condition.
* - The RX software buffer is disabled: returns the data element retrieved
* from the RX FIFO. Undefined data will be returned if the RX FIFO is
* empty.
* - The RX software buffer is enabled: returns data element from the
* software receive buffer.
*
* Parameters:
* None
*
* Return:
* Bits 7-0 contain the next data element from the receive buffer and
* other bits contain the error condition.
*
* Side Effects:
* The errors bits may not correspond with reading characters due to RX FIFO
* and software buffer usage.
* RX software buffer is disabled: The internal software buffer overflow
* is not returned as status by this function.
* Check SCB_rxBufferOverflow to capture that error condition.
*
*******************************************************************************/
uint32 UART_1_UartGetByte(void)
{
uint32 rxData;
uint32 tmpStatus;
#if (UART_1_CHECK_RX_SW_BUFFER)
{
UART_1_DisableInt();
}
#endif
if (0u != UART_1_SpiUartGetRxBufferSize())
{
/* Enables interrupt to receive more bytes: at least one byte is in
* buffer.
*/
#if (UART_1_CHECK_RX_SW_BUFFER)
{
UART_1_EnableInt();
}
#endif
/* Get received byte */
rxData = UART_1_SpiUartReadRxData();
}
else
{
/* Reads a byte directly from RX FIFO: underflow is raised in the case
* of empty. Otherwise the first received byte will be read.
*/
rxData = UART_1_RX_FIFO_RD_REG;
/* Enables interrupt to receive more bytes.
* The RX_NOT_EMPTY interrupt is cleared by the interrupt routine
* in case the byte was received and read by code above.
*/
#if (UART_1_CHECK_RX_SW_BUFFER)
{
UART_1_EnableInt();
}
#endif
}
/* Get and clear RX error mask */
tmpStatus = (UART_1_GetRxInterruptSource() & UART_1_INTR_RX_ERR);
UART_1_ClearRxInterruptSource(UART_1_INTR_RX_ERR);
/* Puts together data and error status:
* MP mode and accept address: 9th bit is set to notify mark.
*/
rxData |= ((uint32) (tmpStatus << 8u));
return (rxData);
}
/*******************************************************************************
* Function Name: UART_1_Stop
********************************************************************************
*
* Summary:
* Disables the SCB component and its interrupt.
*
* Parameters:
* None
*
* Return:
* None
*
*******************************************************************************/
void UART_1_Stop(void)
{
#if(UART_1_SCB_IRQ_INTERNAL)
UART_1_DisableInt();
#endif /* (UART_1_SCB_IRQ_INTERNAL) */
UART_1_CTRL_REG &= (uint32) ~UART_1_CTRL_ENABLED; /* Disable scb IP */
#if(UART_1_SCB_IRQ_INTERNAL)
UART_1_ClearPendingInt();
#endif /* (UART_1_SCB_IRQ_INTERNAL) */
UART_1_ScbModeStop(); /* Calls scbMode specific Stop function */
}
/*******************************************************************************
* Function Name: UART_1_SpiUartClearTxBuffer
****************************************************************************//**
*
* Clears the transmit buffer and TX FIFO.
*
* \globalvars
* UART_1_txBufferHead - the start index to put data into the
* software transmit buffer.
* UART_1_txBufferTail - start index to get data from the software
* transmit buffer.
*
*******************************************************************************/
void UART_1_SpiUartClearTxBuffer(void)
{
#if (UART_1_CHECK_TX_SW_BUFFER)
{
/* Lock from component interruption */
UART_1_DisableInt();
/* Flush TX software buffer */
UART_1_txBufferHead = UART_1_txBufferTail;
UART_1_INTR_TX_MASK_REG &= (uint32) ~UART_1_INTR_TX_NOT_FULL;
UART_1_CLEAR_TX_FIFO;
UART_1_ClearTxInterruptSource(UART_1_INTR_TX_ALL);
/* Release lock */
UART_1_EnableInt();
}
#else
{
UART_1_CLEAR_TX_FIFO;
}
#endif
}
