void C6821::SetCB2(BYTE byData)
{
byData = byData ? 1 : 0;
// CA2 is in input mode
if ( C2_INPUT( m_byCTLB ) )
{
// the new state has caused a transition
if ( m_byICB2 ^ byData )
{
// handle the active transition
if ( ( byData && C2_LOW_TO_HIGH( m_byCTLB ) ) ||
( !byData && C2_HIGH_TO_LOW( m_byCTLB ) ) )
{
// mark the IRQ
SET_IRQ2( m_byCTLB );
// update externals
UpdateInterrupts();
}
}
}
// set the new value for CA2
m_byICB2 = byData;
}
void C6821::SetCA1(BYTE byData)
{
byData = byData ? 1 : 0;
// the new state has caused a transition
if ( m_byCA1 ^ byData )
{
// handle the active transition
if ( ( byData && C1_LOW_TO_HIGH( m_byCTLA ) ) ||
( !byData && C1_HIGH_TO_LOW( m_byCTLA ) ) )
{
// mark the IRQ
SET_IRQ1(m_byCTLA);
// update externals
UpdateInterrupts();
// CA2 is configured as output and in read strobe mode and cleared by a CA1 transition
if ( C2_OUTPUT( m_byCTLA ) && C2_STROBE_MODE( m_byCTLA ) && STROBE_C1_RESET( m_byCTLA ) )
{
// call the CA2 output function
if ( !m_byOCA2 )
PIA_W_CALLBACK( m_stOutCA2, 1 );
// clear CA2
m_byOCA2 = 1;
}
}
}
// set the new value for CA1
m_byCA1 = byData;
}
void CEXIChannel::AddDevice(IEXIDevice* pDevice, const int device_num, bool notifyPresenceChanged)
{
_dbg_assert_(EXPANSIONINTERFACE, device_num < NUM_DEVICES);
// delete the old device
if (m_pDevices[device_num] != NULL)
{
delete m_pDevices[device_num];
m_pDevices[device_num] = NULL;
}
// replace it with the new one
m_pDevices[device_num] = pDevice;
if(notifyPresenceChanged)
{
// This means "device presence changed", software has to check
// m_Status.EXT to see if it is now present or not
if (m_ChannelId != 2)
{
m_Status.EXTINT = 1;
UpdateInterrupts();
}
}
}
void GenerateSIInterrupt(SIInterruptType _SIInterrupt)
{
switch(_SIInterrupt)
{
case INT_RDSTINT: g_ComCSR.RDSTINT = 1; break;
case INT_TCINT: g_ComCSR.TCINT = 1; break;
}
UpdateInterrupts();
}
void GenerateDSPInterrupt(DSPInterruptType type, bool _bSet)
{
switch (type)
{
case INT_DSP: g_dspState.DSPControl.DSP = _bSet ? 1 : 0; break;
case INT_ARAM: g_dspState.DSPControl.ARAM = _bSet ? 1 : 0; if (_bSet) g_dspState.DSPControl.DMAState = 0; break;
case INT_AID: g_dspState.DSPControl.AID = _bSet ? 1 : 0; break;
}
UpdateInterrupts();
}
void GenerateDIInterrupt(DI_InterruptType _DVDInterrupt)
{
switch(_DVDInterrupt)
{
case INT_DEINT: m_DISR.DEINT = 1; break;
case INT_TCINT: m_DISR.TCINT = 1; break;
case INT_BRKINT: m_DISR.BRKINT = 1; break;
case INT_CVRINT: m_DICVR.CVRINT = 1; break;
}
UpdateInterrupts();
}
void Write32(const u32 _iValue, const u32 _iAddress)
{
DEBUG_LOG(DVDINTERFACE, "(w32): 0x%08x @ 0x%08x", _iValue, _iAddress);
switch (_iAddress & 0xFF)
{
case DI_STATUS_REGISTER:
{
UDISR tmpStatusReg(_iValue);
m_DISR.DEINITMASK = tmpStatusReg.DEINITMASK;
m_DISR.TCINTMASK = tmpStatusReg.TCINTMASK;
m_DISR.BRKINTMASK = tmpStatusReg.BRKINTMASK;
m_DISR.BREAK = tmpStatusReg.BREAK;
if (tmpStatusReg.DEINT) m_DISR.DEINT = 0;
if (tmpStatusReg.TCINT) m_DISR.TCINT = 0;
if (tmpStatusReg.BRKINT) m_DISR.BRKINT = 0;
if (m_DISR.BREAK)
{
_dbg_assert_(DVDINTERFACE, 0);
}
UpdateInterrupts();
}
break;
case DI_COVER_REGISTER:
{
UDICVR tmpCoverReg(_iValue);
m_DICVR.CVRINTMASK = tmpCoverReg.CVRINTMASK;
if (tmpCoverReg.CVRINT) m_DICVR.CVRINT = 0;
UpdateInterrupts();
}
break;
case DI_COMMAND_0: m_DICMDBUF[0].Hex = _iValue; break;
case DI_COMMAND_1: m_DICMDBUF[1].Hex = _iValue; break;
case DI_COMMAND_2: m_DICMDBUF[2].Hex = _iValue; break;
case DI_DMA_ADDRESS_REGISTER:
{
m_DIMAR.Hex = _iValue & ~0xfc00001f;
}
break;
case DI_DMA_LENGTH_REGISTER:
{
m_DILENGTH.Hex = _iValue & ~0x1f;
}
break;
case DI_DMA_CONTROL_REGISTER:
{
m_DICR.Hex = _iValue & 7;
if (m_DICR.TSTART)
{
if (!SConfig::GetInstance().m_LocalCoreStartupParameter.bFastDiscSpeed)
{
u64 ticksUntilTC = m_DILENGTH.Length *
(SystemTimers::GetTicksPerSecond() / (SConfig::GetInstance().m_LocalCoreStartupParameter.bWii?DISC_TRANSFER_RATE_WII:DISC_TRANSFER_RATE_GC)) +
(SystemTimers::GetTicksPerSecond() * DISC_ACCESS_TIME_MS / 1000);
CoreTiming::ScheduleEvent((int)ticksUntilTC, tc);
}
else
{
ExecuteCommand(m_DICR);
}
}
}
break;
case DI_IMMEDIATE_DATA_BUFFER: m_DIIMMBUF.Hex = _iValue; break;
case DI_CONFIG_REGISTER:
{
WARN_LOG(DVDINTERFACE, "Write to DICFG, ignored as it's read-only");
}
break;
default:
_dbg_assert_msg_(DVDINTERFACE, 0, "Write to unknown DI address 0x%08x", _iAddress);
break;
}
}
void RegisterMMIO(MMIO::Mapping* mmio, u32 base)
{
// Declare all the boilerplate direct MMIOs.
struct {
u32 addr;
u16* ptr;
bool align_writes_on_32_bytes;
} directly_mapped_vars[] = {
{ AR_INFO, &g_ARAM_Info.Hex },
{ AR_MODE, &g_AR_MODE },
{ AR_REFRESH, &g_AR_REFRESH },
{ AR_DMA_MMADDR_H, MMIO::Utils::HighPart(&g_arDMA.MMAddr) },
{ AR_DMA_MMADDR_L, MMIO::Utils::LowPart(&g_arDMA.MMAddr), true },
{ AR_DMA_ARADDR_H, MMIO::Utils::HighPart(&g_arDMA.ARAddr) },
{ AR_DMA_ARADDR_L, MMIO::Utils::LowPart(&g_arDMA.ARAddr), true },
{ AR_DMA_CNT_H, MMIO::Utils::HighPart(&g_arDMA.Cnt.Hex) },
// AR_DMA_CNT_L triggers DMA
{ AUDIO_DMA_START_HI, MMIO::Utils::HighPart(&g_audioDMA.SourceAddress) },
{ AUDIO_DMA_START_LO, MMIO::Utils::LowPart(&g_audioDMA.SourceAddress) },
};
for (auto& mapped_var : directly_mapped_vars)
{
u16 write_mask = mapped_var.align_writes_on_32_bytes ? 0xFFE0 : 0xFFFF;
mmio->Register(base | mapped_var.addr,
MMIO::DirectRead<u16>(mapped_var.ptr),
MMIO::DirectWrite<u16>(mapped_var.ptr, write_mask)
);
}
// DSP mail MMIOs call DSP emulator functions to get results or write data.
mmio->Register(base | DSP_MAIL_TO_DSP_HI,
MMIO::ComplexRead<u16>([](u32) {
if (dsp_slice > DSP_MAIL_SLICE && dsp_is_lle)
{
dsp_emulator->DSP_Update(DSP_MAIL_SLICE);
dsp_slice -= DSP_MAIL_SLICE;
}
return dsp_emulator->DSP_ReadMailBoxHigh(true);
}),
MMIO::ComplexWrite<u16>([](u32, u16 val) {
dsp_emulator->DSP_WriteMailBoxHigh(true, val);
})
);
mmio->Register(base | DSP_MAIL_TO_DSP_LO,
MMIO::ComplexRead<u16>([](u32) {
return dsp_emulator->DSP_ReadMailBoxLow(true);
}),
MMIO::ComplexWrite<u16>([](u32, u16 val) {
dsp_emulator->DSP_WriteMailBoxLow(true, val);
})
);
mmio->Register(base | DSP_MAIL_FROM_DSP_HI,
MMIO::ComplexRead<u16>([](u32) {
if (dsp_slice > DSP_MAIL_SLICE && dsp_is_lle)
{
dsp_emulator->DSP_Update(DSP_MAIL_SLICE);
dsp_slice -= DSP_MAIL_SLICE;
}
return dsp_emulator->DSP_ReadMailBoxHigh(false);
}),
MMIO::InvalidWrite<u16>()
);
mmio->Register(base | DSP_MAIL_FROM_DSP_LO,
MMIO::ComplexRead<u16>([](u32) {
return dsp_emulator->DSP_ReadMailBoxLow(false);
}),
MMIO::InvalidWrite<u16>()
);
mmio->Register(base | DSP_CONTROL,
MMIO::ComplexRead<u16>([](u32) {
return (g_dspState.DSPControl.Hex & ~DSP_CONTROL_MASK) |
(dsp_emulator->DSP_ReadControlRegister() & DSP_CONTROL_MASK);
}),
MMIO::ComplexWrite<u16>([](u32, u16 val) {
UDSPControl tmpControl;
tmpControl.Hex = (val & ~DSP_CONTROL_MASK) |
(dsp_emulator->DSP_WriteControlRegister(val) & DSP_CONTROL_MASK);
// Not really sure if this is correct, but it works...
// Kind of a hack because DSP_CONTROL_MASK should make this bit
// only viewable to dsp emulator
if (val & 1 /*DSPReset*/)
{
g_audioDMA.AudioDMAControl.Hex = 0;
}
// Update DSP related flags
g_dspState.DSPControl.DSPReset = tmpControl.DSPReset;
g_dspState.DSPControl.DSPAssertInt = tmpControl.DSPAssertInt;
g_dspState.DSPControl.DSPHalt = tmpControl.DSPHalt;
g_dspState.DSPControl.DSPInit = tmpControl.DSPInit;
// Interrupt (mask)
g_dspState.DSPControl.AID_mask = tmpControl.AID_mask;
g_dspState.DSPControl.ARAM_mask = tmpControl.ARAM_mask;
g_dspState.DSPControl.DSP_mask = tmpControl.DSP_mask;
// Interrupt
if (tmpControl.AID) g_dspState.DSPControl.AID = 0;
if (tmpControl.ARAM) g_dspState.DSPControl.ARAM = 0;
if (tmpControl.DSP) g_dspState.DSPControl.DSP = 0;
// unknown
g_dspState.DSPControl.unk3 = tmpControl.unk3;
g_dspState.DSPControl.pad = tmpControl.pad;
if (g_dspState.DSPControl.pad != 0)
{
PanicAlert("DSPInterface (w) g_dspState.DSPControl (CC00500A) gets a value with junk in the padding %08x", val);
}
UpdateInterrupts();
})
);
// ARAM MMIO controlling the DMA start.
mmio->Register(base | AR_DMA_CNT_L,
MMIO::DirectRead<u16>(MMIO::Utils::LowPart(&g_arDMA.Cnt.Hex)),
MMIO::ComplexWrite<u16>([](u32, u16 val) {
g_arDMA.Cnt.Hex = (g_arDMA.Cnt.Hex & 0xFFFF0000) | (val & ~31);
Do_ARAM_DMA();
})
);
// Audio DMA MMIO controlling the DMA start.
mmio->Register(base | AUDIO_DMA_CONTROL_LEN,
MMIO::DirectRead<u16>(&g_audioDMA.AudioDMAControl.Hex),
MMIO::ComplexWrite<u16>([](u32, u16 val) {
g_audioDMA.AudioDMAControl.Hex = val;
g_audioDMA.ReadAddress = g_audioDMA.SourceAddress;
g_audioDMA.BlocksLeft = g_audioDMA.AudioDMAControl.NumBlocks;
})
);
// Audio DMA blocks remaining is invalid to write to, and requires logic on
// the read side.
mmio->Register(base | AUDIO_DMA_BLOCKS_LEFT,
MMIO::ComplexRead<u16>([](u32) {
return (g_audioDMA.BlocksLeft > 0 ? g_audioDMA.BlocksLeft - 1 : 0);
}),
MMIO::InvalidWrite<u16>()
);
// 32 bit reads/writes are a combination of two 16 bit accesses.
for (int i = 0; i < 0x1000; i += 4)
{
mmio->Register(base | i,
MMIO::ReadToSmaller<u32>(mmio, base | i, base | (i + 2)),
MMIO::WriteToSmaller<u32>(mmio, base | i, base | (i + 2))
);
}
}
static void GenerateAudioInterrupt()
{
m_Control.AIINT = 1;
UpdateInterrupts();
}
void RegisterMMIO(MMIO::Mapping* mmio, u32 base)
{
mmio->Register(
base | AI_CONTROL_REGISTER, MMIO::DirectRead<u32>(&m_Control.hex),
MMIO::ComplexWrite<u32>([](u32, u32 val) {
AICR tmpAICtrl(val);
if (m_Control.AIINTMSK != tmpAICtrl.AIINTMSK)
{
DEBUG_LOG(AUDIO_INTERFACE, "Change AIINTMSK to %d", tmpAICtrl.AIINTMSK);
m_Control.AIINTMSK = tmpAICtrl.AIINTMSK;
}
if (m_Control.AIINTVLD != tmpAICtrl.AIINTVLD)
{
DEBUG_LOG(AUDIO_INTERFACE, "Change AIINTVLD to %d", tmpAICtrl.AIINTVLD);
m_Control.AIINTVLD = tmpAICtrl.AIINTVLD;
}
// Set frequency of streaming audio
if (tmpAICtrl.AISFR != m_Control.AISFR)
{
// AISFR rates below are intentionally inverted wrt yagcd
DEBUG_LOG(AUDIO_INTERFACE, "Change AISFR to %s", tmpAICtrl.AISFR ? "48khz" : "32khz");
m_Control.AISFR = tmpAICtrl.AISFR;
g_AISSampleRate = tmpAICtrl.AISFR ? 48000 : 32000;
g_sound_stream->GetMixer()->SetStreamInputSampleRate(g_AISSampleRate);
g_CPUCyclesPerSample = SystemTimers::GetTicksPerSecond() / g_AISSampleRate;
}
// Set frequency of DMA
if (tmpAICtrl.AIDFR != m_Control.AIDFR)
{
DEBUG_LOG(AUDIO_INTERFACE, "Change AIDFR to %s", tmpAICtrl.AIDFR ? "32khz" : "48khz");
m_Control.AIDFR = tmpAICtrl.AIDFR;
g_AIDSampleRate = tmpAICtrl.AIDFR ? 32000 : 48000;
g_sound_stream->GetMixer()->SetDMAInputSampleRate(g_AIDSampleRate);
}
// Streaming counter
if (tmpAICtrl.PSTAT != m_Control.PSTAT)
{
DEBUG_LOG(AUDIO_INTERFACE, "%s streaming audio", tmpAICtrl.PSTAT ? "start" : "stop");
m_Control.PSTAT = tmpAICtrl.PSTAT;
g_LastCPUTime = CoreTiming::GetTicks();
CoreTiming::RemoveEvent(et_AI);
CoreTiming::ScheduleEvent(GetAIPeriod(), et_AI);
}
// AI Interrupt
if (tmpAICtrl.AIINT)
{
DEBUG_LOG(AUDIO_INTERFACE, "Clear AIS Interrupt");
m_Control.AIINT = 0;
}
// Sample Count Reset
if (tmpAICtrl.SCRESET)
{
DEBUG_LOG(AUDIO_INTERFACE, "Reset AIS sample counter");
m_SampleCounter = 0;
g_LastCPUTime = CoreTiming::GetTicks();
}
UpdateInterrupts();
}));
mmio->Register(base | AI_VOLUME_REGISTER, MMIO::DirectRead<u32>(&m_Volume.hex),
MMIO::ComplexWrite<u32>([](u32, u32 val) {
m_Volume.hex = val;
g_sound_stream->GetMixer()->SetStreamingVolume(m_Volume.left, m_Volume.right);
}));
mmio->Register(base | AI_SAMPLE_COUNTER, MMIO::ComplexRead<u32>([](u32) {
return m_SampleCounter +
static_cast<u32>((CoreTiming::GetTicks() - g_LastCPUTime) /
g_CPUCyclesPerSample);
}),
MMIO::ComplexWrite<u32>([](u32, u32 val) {
m_SampleCounter = val;
g_LastCPUTime = CoreTiming::GetTicks();
CoreTiming::RemoveEvent(et_AI);
CoreTiming::ScheduleEvent(GetAIPeriod(), et_AI);
}));
mmio->Register(base | AI_INTERRUPT_TIMING, MMIO::DirectRead<u32>(&m_InterruptTiming),
MMIO::ComplexWrite<u32>([](u32, u32 val) {
DEBUG_LOG(AUDIO_INTERFACE, "AI_INTERRUPT_TIMING=%08x@%08x", val,
PowerPC::ppcState.pc);
m_InterruptTiming = val;
CoreTiming::RemoveEvent(et_AI);
CoreTiming::ScheduleEvent(GetAIPeriod(), et_AI);
}));
}
void UpdateInterrupts_Wrapper(u64 userdata, int cyclesLate)
{
UpdateInterrupts(userdata);
}
void C6821::Write(BYTE byRS, BYTE byData)
{
byRS &= 3;
switch( byRS )
{
/******************* port A output/DDR write *******************/
case PIA_DDRA:
// write output register
if ( OUTPUT_SELECTED( m_byCTLA ) )
{
// update the output value
m_byOA = byData;
// send it to the output function
if ( m_byDDRA )
PIA_W_CALLBACK( m_stOutA, m_byOA & m_byDDRA );
}
// write DDR register
else
{
if ( m_byDDRA != byData )
{
m_byDDRA = byData;
// send it to the output function
if ( m_byDDRA )
PIA_W_CALLBACK( m_stOutA, m_byOA & m_byDDRA );
}
}
break;
/******************* port B output/DDR write *******************/
case PIA_DDRB:
// write output register
if ( OUTPUT_SELECTED( m_byCTLB ) )
{
// update the output value
m_byOB = byData;
// send it to the output function
if ( m_byDDRB )
PIA_W_CALLBACK( m_stOutB, m_byOB & m_byDDRB );
// CB2 is configured as output and in write strobe mode
if ( C2_OUTPUT( m_byCTLB ) && C2_STROBE_MODE( m_byCTLB ) )
{
// this will cause a transition low; call the output function if we're currently high
if ( m_byOCB2 )
PIA_W_CALLBACK( m_stOutCB2, 0 );
m_byOCB2 = 0;
// if the CB2 strobe is cleared by the E, reset it right away
if ( STROBE_E_RESET( m_byCTLB ) )
{
PIA_W_CALLBACK( m_stOutCB2, 1 );
m_byOCB2 = 1;
}
}
}
// write DDR register
else
{
if ( m_byDDRB != byData )
{
m_byDDRB = byData;
// send it to the output function
if ( m_byDDRB )
PIA_W_CALLBACK( m_stOutB, m_byOB & m_byDDRB );
}
}
break;
/******************* port A control write *******************/
case PIA_CTLA:
// Bit 7 and 6 read only
byData &= 0x3f;
// CA2 is configured as output and in set/reset mode
if ( C2_OUTPUT( byData ) )
{
// determine the new value
int temp = SET_C2( byData ) ? 1 : 0;
// if this creates a transition, call the CA2 output function
if ( m_byOCA2 ^ temp)
PIA_W_CALLBACK( m_stOutCA2, temp );
// set the new value
m_byOCA2 = temp;
}
// update the control register
m_byCTLA = ( m_byCTLA & ~0x3F ) | byData;
// update externals
UpdateInterrupts();
break;
/******************* port B control write *******************/
case PIA_CTLB:
/* Bit 7 and 6 read only - PD 16/01/00 */
byData &= 0x3f;
// CB2 is configured as output and in set/reset mode
if ( C2_OUTPUT( byData ) )
{
// determine the new value
int temp = SET_C2( byData ) ? 1 : 0;
// if this creates a transition, call the CA2 output function
if ( m_byOCB2 ^ temp)
PIA_W_CALLBACK( m_stOutCB2, temp );
// set the new value
m_byOCB2 = temp;
}
// update the control register
m_byCTLB = ( m_byCTLB & ~0x3F ) | byData;
// update externals
UpdateInterrupts();
break;
}
}
BYTE C6821::Read(BYTE byRS)
{
BYTE retval = 0;
byRS &= 3;
switch ( byRS )
{
/******************* port A output/DDR read *******************/
case PIA_DDRA:
// read output register
if ( OUTPUT_SELECTED(m_byCTLA) )
{
// combine input and output values
retval = ( m_byOA & m_byDDRA ) | ( m_byIA & ~m_byDDRA );
// IRQ flags implicitly cleared by a read
CLEAR_IRQ1( m_byCTLA );
CLEAR_IRQ1( m_byCTLB );
UpdateInterrupts();
// CA2 is configured as output and in read strobe mode
if ( C2_OUTPUT(m_byCTLA) && C2_STROBE_MODE(m_byCTLA) )
{
// this will cause a transition low; call the output function if we're currently high
if ( m_byOCA2 )
PIA_W_CALLBACK( m_stOutCA2, 0 );
m_byOCA2 = 0;
// if the CA2 strobe is cleared by the E, reset it right away
if ( STROBE_E_RESET( m_byCTLA ) )
{
PIA_W_CALLBACK( m_stOutCA2, 1 );
m_byOCA2 = 1;
}
}
}
// read DDR register
else
{
retval = m_byDDRA;
}
break;
/******************* port B output/DDR read *******************/
case PIA_DDRB:
// read output register
if ( OUTPUT_SELECTED( m_byCTLB ) )
{
// combine input and output values
retval = ( m_byOB & m_byDDRB ) + ( m_byIB & ~m_byDDRB );
// IRQ flags implicitly cleared by a read
CLEAR_IRQ2( m_byCTLA );
CLEAR_IRQ2( m_byCTLB );
UpdateInterrupts();
}
/* read DDR register */
else
{
retval = m_byDDRB;
}
break;
/******************* port A control read *******************/
case PIA_CTLA:
// read control register
retval = m_byCTLA;
// when CA2 is an output, IRQA2 = 0, and is not affected by CA2 transitions.
if ( C2_OUTPUT( m_byCTLA ) )
retval &= ~PIA_IRQ2;
break;
/******************* port B control read *******************/
case PIA_CTLB:
retval = m_byCTLB;
// when CB2 is an output, IRQB2 = 0, and is not affected by CB2 transitions.
if ( C2_OUTPUT( m_byCTLB ) )
retval &= ~PIA_IRQ2;
break;
}
return retval;
}
void CEXIChannel::Write32(const u32 _iValue, const u32 _iRegister)
{
DEBUG_LOG(EXPANSIONINTERFACE, "(w32) 0x%08x channel: %i reg: %s",
_iValue, m_ChannelId, Debug_GetRegisterName(_iRegister));
switch (_iRegister)
{
case EXI_STATUS:
{
UEXI_STATUS newStatus(_iValue);
m_Status.EXIINTMASK = newStatus.EXIINTMASK;
if (newStatus.EXIINT) m_Status.EXIINT = 0;
m_Status.TCINTMASK = newStatus.TCINTMASK;
if (newStatus.TCINT) m_Status.TCINT = 0;
m_Status.CLK = newStatus.CLK;
if (m_ChannelId == 0 || m_ChannelId == 1)
{
m_Status.EXTINTMASK = newStatus.EXTINTMASK;
if (newStatus.EXTINT) m_Status.EXTINT = 0;
}
if (m_ChannelId == 0)
m_Status.ROMDIS = newStatus.ROMDIS;
IEXIDevice* pDevice = GetDevice(m_Status.CHIP_SELECT ^ newStatus.CHIP_SELECT);
m_Status.CHIP_SELECT = newStatus.CHIP_SELECT;
if (pDevice != NULL)
pDevice->SetCS(m_Status.CHIP_SELECT);
UpdateInterrupts();
}
break;
case EXI_DMAADDR:
INFO_LOG(EXPANSIONINTERFACE, "Wrote DMAAddr, chan %i", m_ChannelId);
m_DMAMemoryAddress = _iValue;
break;
case EXI_DMALENGTH:
INFO_LOG(EXPANSIONINTERFACE, "Wrote DMALength, chan %i", m_ChannelId);
m_DMALength = _iValue;
break;
case EXI_DMACONTROL:
INFO_LOG(EXPANSIONINTERFACE, "Wrote DMAControl, chan %i", m_ChannelId);
m_Control.Hex = _iValue;
if (m_Control.TSTART)
{
IEXIDevice* pDevice = GetDevice(m_Status.CHIP_SELECT);
if (pDevice == NULL)
return;
if (m_Control.DMA == 0)
{
// immediate data
switch (m_Control.RW)
{
case EXI_READ: m_ImmData = pDevice->ImmRead(m_Control.TLEN + 1); break;
case EXI_WRITE: pDevice->ImmWrite(m_ImmData, m_Control.TLEN + 1); break;
case EXI_READWRITE: pDevice->ImmReadWrite(m_ImmData, m_Control.TLEN + 1); break;
default: _dbg_assert_msg_(EXPANSIONINTERFACE,0,"EXI Imm: Unknown transfer type %i", m_Control.RW);
}
m_Control.TSTART = 0;
}
else
{
// DMA
switch (m_Control.RW)
{
case EXI_READ: pDevice->DMARead (m_DMAMemoryAddress, m_DMALength); break;
case EXI_WRITE: pDevice->DMAWrite(m_DMAMemoryAddress, m_DMALength); break;
default: _dbg_assert_msg_(EXPANSIONINTERFACE,0,"EXI DMA: Unknown transfer type %i", m_Control.RW);
}
m_Control.TSTART = 0;
}
if(!m_Control.TSTART) // completed !
{
m_Status.TCINT = 1;
UpdateInterrupts();
}
}
break;
case EXI_IMMDATA:
INFO_LOG(EXPANSIONINTERFACE, "Wrote IMMData, chan %i", m_ChannelId);
m_ImmData = _iValue;
break;
}
}