void
init_emacps(xemacpsif_s *xemacps, struct netif *netif)
{
int rdy;
unsigned mac_address = (unsigned)(netif->state);
unsigned link_speed = 1000;
unsigned options;
unsigned lock_message_printed = 0;
XEmacPs *xemacpsp;
XEmacPs_Config *mac_config;
int Status = XST_SUCCESS;
/* obtain config of this emac */
mac_config = lookup_config(mac_address);
xemacpsp = &xemacps->emacps;
#if 0
options = XEmacPs_GetOptions(xemacpsp);
options |= XEMACPS_FLOW_CONTROL_OPTION;
options |= XEMACPS_TRANSMITTER_ENABLE_OPTION;
options |= XEMACPS_RECEIVER_ENABLE_OPTION;
options |= XEMACPS_FCS_STRIP_OPTION;
options |= XEMACPS_BROADCAST_OPTION;
options |= XEMACPS_FCS_INSERT_OPTION;
options |= XEMACPS_RX_CHKSUM_ENABLE_OPTION;
options |= XEMACPS_TX_CHKSUM_ENABLE_OPTION;
options |= XEMACPS_LENTYPE_ERR_OPTION;
XEmacPs_SetOptions(xemacpsp, options);
XEmacPs_ClearOptions(xemacpsp, ~options);
#endif
/* set mac address */
Status = XEmacPs_SetMacAddress(xemacpsp, (void*)(netif->hwaddr), 1);
if (Status != XST_SUCCESS) {
xil_printf("In %s:Emac Mac Address set failed...\r\n",__func__);
}
link_speed = Phy_Setup(xemacpsp);
XEmacPs_SetOperatingSpeed(xemacpsp, link_speed);
/* Setting the operating speed of the MAC needs a delay. */
{
volatile int wait;
for (wait=0; wait < 20000; wait++);
}
Status = XEmacPs_SetOptions(xemacpsp, XEMACPS_PROMISC_OPTION);
if (Status != XST_SUCCESS) {
xil_printf("In %s:Setting up of promiscuous mode failed...\r\n",__func__);
}
}
/**
* This function resets the device but preserves the options set by the user.
*
* The descriptor list could be reinitialized with the same calls to
* XEmacPs_BdRingClone() as used in main(). Doing this is a matter of
* preference.
* In many cases, an OS may have resources tied up in the descriptors.
* Reinitializing in this case may bad for the OS since its resources may be
* permamently lost.
*
* @param EmacPsInstancePtr is a pointer to the instance of the EmacPs
* driver.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
*****************************************************************************/
static int EmacPsResetDevice(XEmacPs * EmacPsInstancePtr)
{
int Status = 0;
u8 MacSave[6];
u32 Options;
XEmacPs_Bd BdTemplate;
/*
* Stop device
*/
XEmacPs_Stop(EmacPsInstancePtr);
/*
* Save the device state
*/
XEmacPs_GetMacAddress(EmacPsInstancePtr, &MacSave, 1);
Options = XEmacPs_GetOptions(EmacPsInstancePtr);
/*
* Stop and reset the device
*/
XEmacPs_Reset(EmacPsInstancePtr);
/*
* Restore the state
*/
XEmacPs_SetMacAddress(EmacPsInstancePtr, &MacSave, 1);
Status |= XEmacPs_SetOptions(EmacPsInstancePtr, Options);
Status |= XEmacPs_ClearOptions(EmacPsInstancePtr, ~Options);
if (Status != XST_SUCCESS) {
EmacPsUtilErrorTrap("Error restoring state after reset");
return XST_FAILURE;
}
/*
* Setup callbacks
*/
Status = XEmacPs_SetHandler(EmacPsInstancePtr,
XEMACPS_HANDLER_DMASEND,
(void *) XEmacPsSendHandler,
EmacPsInstancePtr);
Status |= XEmacPs_SetHandler(EmacPsInstancePtr,
XEMACPS_HANDLER_DMARECV,
(void *) XEmacPsRecvHandler,
EmacPsInstancePtr);
Status |= XEmacPs_SetHandler(EmacPsInstancePtr, XEMACPS_HANDLER_ERROR,
(void *) XEmacPsErrorHandler,
EmacPsInstancePtr);
if (Status != XST_SUCCESS) {
EmacPsUtilErrorTrap("Error assigning handlers");
return XST_FAILURE;
}
/*
* Setup RxBD space.
*
* We have already defined a properly aligned area of memory to store
* RxBDs at the beginning of this source code file so just pass its
* address into the function. No MMU is being used so the physical and
* virtual addresses are the same.
*
* Setup a BD template for the Rx channel. This template will be copied
* to every RxBD. We will not have to explicitly set these again.
*/
XEmacPs_BdClear(&BdTemplate);
/*
* Create the RxBD ring
*/
Status = XEmacPs_BdRingCreate(&(XEmacPs_GetRxRing
(EmacPsInstancePtr)),
RX_BD_LIST_START_ADDRESS,
RX_BD_LIST_START_ADDRESS,
XEMACPS_BD_ALIGNMENT,
RXBD_CNT);
if (Status != XST_SUCCESS) {
EmacPsUtilErrorTrap
("Error setting up RxBD space, BdRingCreate");
return XST_FAILURE;
}
Status = XEmacPs_BdRingClone(&
(XEmacPs_GetRxRing(EmacPsInstancePtr)),
&BdTemplate, XEMACPS_RECV);
if (Status != XST_SUCCESS) {
EmacPsUtilErrorTrap
("Error setting up RxBD space, BdRingClone");
return XST_FAILURE;
}
/*
* Setup TxBD space.
*
* Like RxBD space, we have already defined a properly aligned area of
* memory to use.
*
* Also like the RxBD space, we create a template. Notice we don't set
* the "last" attribute. The examples will be overriding this
* attribute so it does no good to set it up here.
*/
XEmacPs_BdClear(&BdTemplate);
XEmacPs_BdSetStatus(&BdTemplate, XEMACPS_TXBUF_USED_MASK);
/*
* Create the TxBD ring
*/
Status = XEmacPs_BdRingCreate(&(XEmacPs_GetTxRing
(EmacPsInstancePtr)),
TX_BD_LIST_START_ADDRESS,
TX_BD_LIST_START_ADDRESS,
XEMACPS_BD_ALIGNMENT,
TXBD_CNT);
if (Status != XST_SUCCESS) {
EmacPsUtilErrorTrap
("Error setting up TxBD space, BdRingCreate");
return XST_FAILURE;
}
Status = XEmacPs_BdRingClone(&
(XEmacPs_GetTxRing(EmacPsInstancePtr)),
&BdTemplate, XEMACPS_SEND);
if (Status != XST_SUCCESS) {
EmacPsUtilErrorTrap
("Error setting up TxBD space, BdRingClone");
return XST_FAILURE;
}
/*
* Restart the device
*/
XEmacPs_Start(EmacPsInstancePtr);
return XST_SUCCESS;
}
