/**
* This function resets the device but preserves the options set by the user.
*
* The descriptor list could be reinitialized with the same calls to
* XLlTemac_SgSetSpace() as used in main(). Doing this is a matter of preference.
* In many cases, an OS may have resources tied up in the descriptors.
* Reinitializing in this case may bad for the OS since its resources may be
* permamently lost.
*
* @param TemacInstancePtr is a pointer to the instance of the Temac
* component.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
******************************************************************************/
static int TemacResetDevice(XLlTemac * TemacInstancePtr,
XLlDma * DmaInstancePtr)
{
int Status;
u8 MacSave[6];
u32 Options;
//u32 RxThreshold = 1;
//u32 TxThreshold = 1;
//u32 RxWaitbound = 0;
//u32 TxWaitbound = 0;
//XLlDma_BdRing * RxRingPtr = &XLlDma_GetRxRing(DmaInstancePtr);
//XLlDma_BdRing * TxRingPtr = &XLlDma_GetTxRing(DmaInstancePtr);
/*
* Stop LLTEMAC device
*/
XLlTemac_Stop(TemacInstancePtr);
/*
* Save the device state
*/
XLlTemac_GetMacAddress(TemacInstancePtr, MacSave);
Options = XLlTemac_GetOptions(TemacInstancePtr);
/*
* Stop and reset the device
*/
XLlTemac_Reset(TemacInstancePtr, XTE_NORESET_HARD);
/*
* Restore the state
*/
Status = XLlTemac_SetMacAddress(TemacInstancePtr, MacSave);
Status |= XLlTemac_SetOptions(TemacInstancePtr, Options);
Status |= XLlTemac_ClearOptions(TemacInstancePtr, ~Options);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error restoring state after reset");
return XST_FAILURE;
}
/*
* Restart the device
*/
XLlTemac_Start(TemacInstancePtr);
return XST_SUCCESS;
}
void
init_lltemac(xlltemacif_s *xlltemacif, struct netif *netif)
{
int rdy;
unsigned mac_address = (unsigned)(netif->state);
unsigned link_speed = 1000;
unsigned options;
unsigned lock_message_printed = 0;
/* obtain config of this emac */
XLlTemac_Config *mac_config = lookup_config(mac_address);
XLlTemac *xlltemacp = &xlltemacif->lltemac;
XLlTemac_CfgInitialize(xlltemacp, mac_config, mac_config->BaseAddress);
options = XLlTemac_GetOptions(xlltemacp);
options |= XTE_FLOW_CONTROL_OPTION;
options |= XTE_JUMBO_OPTION;
options |= XTE_TRANSMITTER_ENABLE_OPTION;
options |= XTE_RECEIVER_ENABLE_OPTION;
options |= XTE_FCS_STRIP_OPTION;
options |= XTE_MULTICAST_OPTION;
XLlTemac_SetOptions(xlltemacp, options);
XLlTemac_ClearOptions(xlltemacp, ~options);
/* set mac address */
XLlTemac_SetMacAddress(xlltemacp, (Xuint8*)(netif->hwaddr));
/* make sure the hard TEMAC is ready */
rdy = XLlTemac_ReadReg(xlltemacp->Config.BaseAddress,
XTE_RDY_OFFSET);
while ((rdy & XTE_RDY_HARD_ACS_RDY_MASK) == 0) {
rdy = XLlTemac_ReadReg(xlltemacp->Config.BaseAddress,
XTE_RDY_OFFSET);
}
link_speed = Phy_Setup(xlltemacp);
XLlTemac_SetOperatingSpeed(xlltemacp, link_speed);
/* Setting the operating speed of the MAC needs a delay. */
{
volatile int wait;
for (wait=0; wait < 100000; wait++);
for (wait=0; wait < 100000; wait++);
}
/* in a soft temac implementation, we need to explicitly make sure that
* the RX DCM has been locked. See xps_ll_temac manual for details.
* This bit is guaranteed to be 1 for hard temac's
*/
lock_message_printed = 0;
while (!(XLlTemac_ReadReg(xlltemacp->Config.BaseAddress, XTE_IS_OFFSET)
& XTE_INT_RXDCM_LOCK_MASK)) {
int first = 1;
if (first) {
print("Waiting for RX DCM to lock..");
first = 0;
lock_message_printed = 1;
}
}
if (lock_message_printed)
print("RX DCM locked.\r\n");
/* start the temac */
XLlTemac_Start(xlltemacp);
/* enable TEMAC interrupts */
XLlTemac_IntEnable(xlltemacp, XTE_INT_RECV_ERROR_MASK);
}
/**
*
* This function demonstrates the usage of the TEMAC by sending and receiving
* a single frame in SGDMA interrupt mode.
* The source packet will be described by two descriptors. It will be received
* into a buffer described by a single descriptor.
*
* @param TemacInstancePtr is a pointer to the instance of the Temac
* component.
*
* @return XST_SUCCESS to indicate success, otherwise XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int TemacSgDmaIntrSingleFrameExample(XLlTemac * TemacInstancePtr,
XLlDma * DmaInstancePtr)
{
int Status;
u32 TxFrameLength;
int PayloadSize = 1000;
XLlDma_BdRing *RxRingPtr = &XLlDma_GetRxRing(DmaInstancePtr);
XLlDma_BdRing *TxRingPtr = &XLlDma_GetTxRing(DmaInstancePtr);
XLlDma_Bd *Bd1Ptr;
XLlDma_Bd *Bd2Ptr;
/*
* Clear variables shared with callbacks
*/
FramesRx = 0;
FramesTx = 0;
DeviceErrors = 0;
/*
* Calculate the frame length (not including FCS)
*/
TxFrameLength = XTE_HDR_SIZE + PayloadSize;
/*
* Setup packet to be transmitted
*/
TemacUtilFrameHdrFormatMAC(&TxFrame, TemacMAC);
TemacUtilFrameHdrFormatType(&TxFrame, PayloadSize);
TemacUtilFrameSetPayloadData(&TxFrame, PayloadSize);
/*
* Flush the TX frame before giving it to DMA TX channel to transmit,
* in case D-Caching is turned on.
*/
XCACHE_FLUSH_DCACHE_RANGE(&TxFrame, TxFrameLength);
/*
* Clear out receive packet memory area
*/
TemacUtilFrameMemClear(&RxFrame);
/*
* Invalidate the RX frame before giving it to DMA RX channel to
* receive data, in case D-Caching is turned on.
*/
XCACHE_INVALIDATE_DCACHE_RANGE(&RxFrame, TxFrameLength);
/*
* Start the LLTEMAC device and enable the ERROR interrupt
*/
XLlTemac_Start(TemacInstancePtr);
XLlTemac_IntEnable(TemacInstancePtr, XTE_INT_RECV_ERROR_MASK);
/*
* Allocate 1 RxBD. Note that TEMAC utilizes an in-place allocation
* scheme. The returned Bd1Ptr will point to a free BD in the memory
* segment setup with the call to XLlTemac_SgSetSpace()
*/
Status = XLlDma_BdRingAlloc(RxRingPtr, 1, &Bd1Ptr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error allocating RxBD");
return XST_FAILURE;
}
/*
* Setup the BD. The BD template used in the call to XLlTemac_SgSetSpace()
* set the "last" field of all RxBDs. Therefore we are not required to
* issue a XLlDma_Bd_mSetLast(Bd1Ptr) here.
*/
XLlDma_BdSetBufAddr(Bd1Ptr, &RxFrame);
XLlDma_BdSetLength(Bd1Ptr, sizeof(RxFrame));
XLlDma_BdSetStsCtrl(Bd1Ptr, XLLDMA_BD_STSCTRL_SOP_MASK | XLLDMA_BD_STSCTRL_EOP_MASK);
/*
* Enqueue to HW
*/
Status = XLlDma_BdRingToHw(RxRingPtr, 1, Bd1Ptr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error committing RxBD to HW");
return XST_FAILURE;
}
/*
* Enable DMA RX interrupt.
*
* Interrupt coalescing parameters are left at their default settings
* which is to interrupt the processor after every frame has been
* processed by the DMA engine.
*/
XLlDma_BdRingIntEnable(RxRingPtr, XLLDMA_CR_IRQ_ALL_EN_MASK);
/*
* Start DMA RX channel. Now it's ready to receive data.
*/
Status = XLlDma_BdRingStart(RxRingPtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Allocate, setup, and enqueue 2 TxBDs. The first BD will describe
* the first 32 bytes of TxFrame and the second BD will describe the
* rest of the frame.
*
* The function below will allocate two adjacent BDs with Bd1Ptr being
* set as the lead BD.
*/
Status = XLlDma_BdRingAlloc(TxRingPtr, 2, &Bd1Ptr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error allocating TxBD");
return XST_FAILURE;
}
/*
* Setup TxBD #1
*/
XLlDma_BdSetBufAddr(Bd1Ptr, &TxFrame);
XLlDma_BdSetLength(Bd1Ptr, 32);
XLlDma_BdSetStsCtrl(Bd1Ptr, XLLDMA_BD_STSCTRL_SOP_MASK);
/*
* Setup TxBD #2
*/
Bd2Ptr = XLlDma_BdRingNext(TxRingPtr, Bd1Ptr);
XLlDma_BdSetBufAddr(Bd2Ptr, (u32) (&TxFrame) + 32);
XLlDma_BdSetLength(Bd2Ptr, TxFrameLength - 32);
XLlDma_BdSetStsCtrl(Bd2Ptr, XLLDMA_BD_STSCTRL_EOP_MASK);
/*
* Enqueue to HW
*/
Status = XLlDma_BdRingToHw(TxRingPtr, 2, Bd1Ptr);
if (Status != XST_SUCCESS) {
/*
* Undo BD allocation and exit
*/
XLlDma_BdRingUnAlloc(TxRingPtr, 2, Bd1Ptr);
TemacUtilErrorTrap("Error committing TxBD to HW");
return XST_FAILURE;
}
/*
* Enable DMA transmit interrupts
*/
XLlDma_BdRingIntEnable(TxRingPtr, XLLDMA_CR_IRQ_ALL_EN_MASK);
/*
* Start DMA TX channel. Transmission starts at once.
*/
Status = XLlDma_BdRingStart(TxRingPtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait for transmission to complete
*/
while (!FramesTx);
/*
* Now that the frame has been sent, post process our TxBDs.
* Since we have only submitted 2 to HW, then there should be only 2 ready
* for post processing.
*/
if (XLlDma_BdRingFromHw(TxRingPtr, 2, &Bd1Ptr) == 0) {
TemacUtilErrorTrap("TxBDs were not ready for post processing");
return XST_FAILURE;
}
/*
* Examine the TxBDs.
*
* There isn't much to do. The only thing to check would be DMA exception
* bits. But this would also be caught in the error handler. So we just
* return these BDs to the free list
*/
Status = XLlDma_BdRingFree(TxRingPtr, 2, Bd1Ptr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error freeing up TxBDs");
return XST_FAILURE;
}
/*
* Wait for Rx indication
*/
while (!FramesRx);
printf("Transmitted Packet!\r\n");
printf("\r\n");
/*
* Now that the frame has been received, post process our RxBD.
* Since we have only submitted 1 to HW, then there should be only 1 ready
* for post processing.
*/
if (XLlDma_BdRingFromHw(RxRingPtr, 1, &Bd1Ptr) == 0) {
TemacUtilErrorTrap("RxBD was not ready for post processing");
return XST_FAILURE;
}
/*
* There is no device status to check. If there was a DMA error, it
* should have been reported to the error handler. Check the receive
* length against the transmitted length, then verify the data.
*
* Note in LLTEMAC case, USR4_OFFSET word in the RX BD is used to store
* the real length of the received packet
*/
if ((XLlDma_BdRead(Bd1Ptr, XLLDMA_BD_USR4_OFFSET) & 0x3FFF)
!= TxFrameLength) {
TemacUtilErrorTrap("Length mismatch");
return XST_FAILURE;
}
if (TemacUtilFrameVerify(&TxFrame, &RxFrame) != 0) {
TemacUtilErrorTrap("Data mismatch");
return XST_FAILURE;
}
/*
* Return the RxBD back to the channel for later allocation. Free the
* exact number we just post processed.
*/
Status = XLlDma_BdRingFree(RxRingPtr, 1, Bd1Ptr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error freeing up TxBDs");
return XST_FAILURE;
}
/*
* Finished this example. If everything worked correctly, all TxBDs and
* RxBDs should be free for allocation. Stop the device.
*/
XLlTemac_Stop(TemacInstancePtr);
return XST_SUCCESS;
}
static err_t
xlltemacif_mac_filter_update (struct netif *netif, struct ip_addr *group,
u8_t action)
{
err_t return_val = ERR_OK;
u8_t multicast_mac_addr[6];
u8_t multicast_mac_addr_to_clr[6];
u8_t temp_mask;
int entry;
int i;
u8_t * ip_addr_temp = (u8_t *)group;
struct xemac_s *xemac = (struct xemac_s *)(netif->state);
xlltemacif_s *xlltemacif = (xlltemacif_s *)(xemac->state);
if (action == IGMP_ADD_MAC_FILTER) {
if ((ip_addr_temp[0] >= 224) && (ip_addr_temp[0] <= 239)) {
if (xlltemac_mcast_entry_mask >= 0x0F) {
LWIP_DEBUGF(NETIF_DEBUG,
("xlltemacif_mac_filter_update: No multicast address registers left.\r\n"));
LWIP_DEBUGF(NETIF_DEBUG,
(" Multicast MAC address add operation failure !!\r\n"));
return_val = ERR_MEM;
} else {
for (i = 0; i < 4; i++) {
temp_mask = (0x01) << i;
if ((xlltemac_mcast_entry_mask &
temp_mask) == temp_mask) {
continue;
} else {
entry = i;
xlltemac_mcast_entry_mask |=
temp_mask;
multicast_mac_addr[0] = 0x01;
multicast_mac_addr[1] = 0x00;
multicast_mac_addr[2] = 0x5E;
multicast_mac_addr[3] =
ip_addr_temp[1] & 0x7F;
multicast_mac_addr[4] =
ip_addr_temp[2];
multicast_mac_addr[5] =
ip_addr_temp[3];
XLlTemac_Stop
(&xlltemacif->lltemac);
XLlTemac_MulticastAdd
(&xlltemacif->lltemac,
multicast_mac_addr,entry);
XLlTemac_Start
(&xlltemacif->lltemac);
LWIP_DEBUGF(NETIF_DEBUG,
("xlltemacif_mac_filter_update: Muticast MAC address successfully added.\r\n"));
return_val = ERR_OK;
break;
}
}
if (i == 4) {
LWIP_DEBUGF(NETIF_DEBUG,
("xlltemacif_mac_filter_update: No multicast address registers left.\r\n"));
LWIP_DEBUGF(NETIF_DEBUG,
(" Multicast MAC address add operation failure !!\r\n"));
return_val = ERR_MEM;
}
}
} else {
LWIP_DEBUGF(NETIF_DEBUG,
("xlltemacif_mac_filter_update: The requested MAC address is not a multicast address.\r\n"));
LWIP_DEBUGF(NETIF_DEBUG,
(" Multicast address add operation failure !!\r\n"));
return_val = ERR_ARG;
}
} else if (action == IGMP_DEL_MAC_FILTER) {
if ((ip_addr_temp[0] < 224) || (ip_addr_temp[0] > 239)) {
LWIP_DEBUGF(NETIF_DEBUG,
("xlltemacif_mac_filter_update: The requested MAC address is not a multicast address.\r\n"));
LWIP_DEBUGF(NETIF_DEBUG,
(" Multicast address add operation failure !!\r\n"));
return_val = ERR_ARG;
} else {
for (i = 0; i < 4; i++) {
temp_mask = (0x01) << i;
if ((xlltemac_mcast_entry_mask & temp_mask)
== temp_mask) {
XLlTemac_MulticastGet
(&xlltemacif->lltemac,
multicast_mac_addr_to_clr, i);
if ((ip_addr_temp[3] ==
multicast_mac_addr_to_clr[5]) &&
(ip_addr_temp[2] ==
multicast_mac_addr_to_clr[4]) &&
((ip_addr_temp[1] & 0x7f) ==
multicast_mac_addr_to_clr[3])) {
XLlTemac_Stop
(&xlltemacif->lltemac);
XLlTemac_MulticastClear
(&xlltemacif->lltemac, i);
XLlTemac_Start
(&xlltemacif->lltemac);
return_val = ERR_OK;
xlltemac_mcast_entry_mask
&= (~temp_mask);
break;
} else {
continue;
}
} else {
continue;
}
}
if (i == 4) {
LWIP_DEBUGF(NETIF_DEBUG,
("xlltemacif_mac_filter_update: No multicast address registers present with\r\n"));
LWIP_DEBUGF(NETIF_DEBUG,
(" the requested Multicast MAC address.\r\n"));
LWIP_DEBUGF(NETIF_DEBUG,
(" Multicast MAC address removal failure!!.\r\n"));
return_val = ERR_MEM;
}
}
}
return return_val;
}
/**
*
* This example sends and receives a single packet in loopback mode with checksum
* offloading support.
*
* The transmit frame will be checksummed over the entire Ethernet payload
* and inserted into the last 2 bytes of the frame.
*
* On receive, HW should calculate the Ethernet payload checksum and return a
* value of 0xFFFF which means the payload data was likely not corrupted.
*
* @param TemacInstancePtr is a pointer to the instance of the Temac
* component.
*
* @return XST_SUCCESS to indicate success, otherwise XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int TemacSgDmaChecksumOffloadExample(XLlTemac * TemacInstancePtr,
XLlDma * DmaInstancePtr)
{
int Status;
u32 TxFrameLength;
int PayloadSize = 1000;
XLlDma_BdRing *RxRingPtr = &XLlDma_mGetRxRing(DmaInstancePtr);
XLlDma_BdRing *TxRingPtr = &XLlDma_mGetTxRing(DmaInstancePtr);
XLlDma_Bd *BdPtr;
/*
* Cannot run this example if checksum offloading support is not available
*/
if (!(XLlTemac_IsRxCsum(TemacInstancePtr) &&
XLlTemac_IsTxCsum(TemacInstancePtr))) {
TemacUtilErrorTrap("Checksum offloading not available");
return XST_FAILURE;
}
/*
* Clear variables shared with callbacks
*/
FramesRx = 0;
FramesTx = 0;
DeviceErrors = 0;
/*
* Calculate frame length (not including FCS)
*/
TxFrameLength = XTE_HDR_SIZE + PayloadSize;
/*
* Setup the packet to be transmitted,
* Last 2 bytes are reserved for checksum
*/
TemacUtilFrameMemClear(&TxFrame);
TemacUtilFrameHdrFormatMAC(&TxFrame, TemacMAC);
TemacUtilFrameHdrFormatType(&TxFrame, PayloadSize);
TemacUtilFrameSetPayloadData(&TxFrame, PayloadSize - 2);
/*
* Flush the TX frame before giving it to DMA TX channel to transmit,
* in case D-Caching is turned on.
*/
XCACHE_FLUSH_DCACHE_RANGE(&TxFrame, TxFrameLength);
/*
* Clear out receive packet memory area
*/
TemacUtilFrameMemClear(&RxFrame);
/*
* Invalidate the RX frame before giving it to DMA RX channel to
* receive data, in case D-Caching is turned on.
*/
XCACHE_INVALIDATE_DCACHE_RANGE(&RxFrame, TxFrameLength);
/*
* Interrupt coalescing parameters are set to their default settings
* which is to interrupt the processor after every frame has been
* processed by the DMA engine.
*/
Status = XLlDma_BdRingSetCoalesce(TxRingPtr, 1, 1);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error setting coalescing for transmit");
return XST_FAILURE;
}
Status = XLlDma_BdRingSetCoalesce(RxRingPtr, 1, 1);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error setting coalescing for recv");
return XST_FAILURE;
}
/*
* Make sure Tx and Rx are enabled
*/
Status = XLlTemac_SetOptions(TemacInstancePtr,
XTE_RECEIVER_ENABLE_OPTION |
XTE_TRANSMITTER_ENABLE_OPTION);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error setting options");
return XST_FAILURE;
}
/*
* Start the LLTEMAC and enable its ERROR interrupts
*/
XLlTemac_Start(TemacInstancePtr);
XLlTemac_IntEnable(TemacInstancePtr, XTE_INT_RECV_ERROR_MASK);
/*
* Allocate 1 RxBD. Note that TEMAC utilizes an in-place allocation
* scheme. The returned BdPtr will point to a free BD in the memory
* segment setup with the call to XLlTemac_SgSetSpace()
*/
Status = XLlDma_BdRingAlloc(RxRingPtr, 1, &BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error allocating RxBD");
return XST_FAILURE;
}
/*
* Setup the BD. The BD template used in the call to XLlTemac_SgSetSpace()
* set the SOP and EOP fields of all RxBDs.
*/
XLlDma_mBdSetBufAddr(BdPtr, &RxFrame);
XLlDma_mBdSetLength(BdPtr, sizeof(RxFrame));
XLlDma_mBdSetStsCtrl(BdPtr, XLLDMA_BD_STSCTRL_SOP_MASK |
XLLDMA_BD_STSCTRL_EOP_MASK);
/*
* Enqueue to HW
*/
Status = XLlDma_BdRingToHw(RxRingPtr, 1, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error committing RxBD to HW");
return XST_FAILURE;
}
/*
* Enable DMA receive related interrupts
*/
XLlDma_mBdRingIntEnable(RxRingPtr, XLLDMA_CR_IRQ_ALL_EN_MASK);
/*
* As DMA RX channel has been started in
* TemacSgDmaIntrSingleFrameExample() above, there is no need to start
* it again here
*/
/*
* Allocate 1 TxBD
*/
Status = XLlDma_BdRingAlloc(TxRingPtr, 1, &BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error allocating TxBD");
return XST_FAILURE;
}
/*
* Setup the TxBD
*/
XLlDma_mBdSetBufAddr(BdPtr, &TxFrame);
XLlDma_mBdSetLength(BdPtr, TxFrameLength);
XLlDma_mBdSetStsCtrl(BdPtr, XLLDMA_BD_STSCTRL_SOP_MASK |
XLLDMA_BD_STSCTRL_EOP_MASK);
/*
* Setup TxBd checksum offload attributes.
* Note that the checksum offload values can be set globally for all TxBds
* when XLlDma_BdRingClone() is called to setup Tx BD space. This would
* eliminate the need to set them here.
*/
/* Enable hardware checksum computation for the buffer descriptor */
XLlDma_mBdWrite((BdPtr), XLLDMA_BD_STSCTRL_USR0_OFFSET,
(XLlDma_mBdRead((BdPtr), XLLDMA_BD_STSCTRL_USR0_OFFSET)
| CSUM_ENABLE));
/* Write Start Offset and Insert Offset into BD */
XLlDma_mBdWrite(BdPtr, XLLDMA_BD_USR1_OFFSET,
XTE_HDR_SIZE << 16 | TxFrameLength - 2);
/* Write 0, as the seed value, to the BD */
XLlDma_mBdWrite(BdPtr, XLLDMA_BD_USR2_OFFSET, 0);
/*
* Enqueue to HW
*/
Status = XLlDma_BdRingToHw(TxRingPtr, 1, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error committing TxBD to HW");
return XST_FAILURE;
}
/*
* Enable DMA transmit related interrupts
*/
XLlDma_mBdRingIntEnable(TxRingPtr, XLLDMA_CR_IRQ_ALL_EN_MASK);
/*
* As DMA TX channel has been started in
* TemacSgDmaIntrSingleFrameExample() above, there is no need to start
* it again here
*/
/*
* Wait for transmission to complete
*/
while (!FramesTx);
/*
* Now that the frame has been sent, post process our TxBDs.
* Since we have only submitted 2 to HW, then there should be only 2 ready
* for post processing.
*/
if (XLlDma_BdRingFromHw(TxRingPtr, 1, &BdPtr) == 0) {
TemacUtilErrorTrap("TxBDs were not ready for post processing");
return XST_FAILURE;
}
/*
* Examine the TxBDs.
*
* There isn't much to do. The only thing to check would be DMA exception
* bits. But this would also be caught in the error handler. So we just
* return these BDs to the free list
*/
Status = XLlDma_BdRingFree(TxRingPtr, 1, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error freeing up TxBDs");
return XST_FAILURE;
}
/*
* Wait for Rx indication
*/
while (!FramesRx);
/*
* Now that the frame has been received, post process our RxBD.
* Since we have only submitted 1 to HW, then there should be only 1 ready
* for post processing.
*/
if (XLlDma_BdRingFromHw(RxRingPtr, 1, &BdPtr) == 0) {
TemacUtilErrorTrap("RxBD was not ready for post processing");
return XST_FAILURE;
}
/*
* There is no device status to check. If there was a DMA error, it should
* have been reported to the error handler. Check the receive length against
* the transmitted length, then verify the data.
*
* Note in LLTEMAC case, USR4_OFFSET word in the RX BD is used to store
* the real length of the received packet
*/
if (XLlDma_mBdRead(BdPtr, XLLDMA_BD_USR4_OFFSET) != TxFrameLength) {
TemacUtilErrorTrap("Length mismatch");
}
/*
* Verify the checksum as computed by HW. It should add up to 0xFFFF
* if frame was uncorrupted
*/
if ((u16) (XLlDma_mBdRead(BdPtr, XLLDMA_BD_USR3_OFFSET))
!= 0xFFFF) {
TemacUtilErrorTrap("Rx checksum incorrect");
return XST_FAILURE;
}
/*
* Return the RxBD back to the channel for later allocation. Free the
* exact number we just post processed.
*/
Status = XLlDma_BdRingFree(RxRingPtr, 1, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error freeing up TxBDs");
return XST_FAILURE;
}
/*
* Finished this example. If everything worked correctly, all TxBDs and
* RxBDs should be free for allocation. Stop the device.
*/
XLlTemac_Stop(TemacInstancePtr);
return XST_SUCCESS;
}
/**
*
* This example sends frames with the interrupt coalescing settings altered
* from their defaults.
*
* The default settings will interrupt the processor after every frame has been
* sent. This example will increase the threshold resulting in lower CPU
* utilization since it spends less time servicing interrupts.
*
* @param TemacInstancePtr is a pointer to the instance of the Temac
* component.
*
* @return XST_SUCCESS to indicate success, otherwise XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int TemacSgDmaIntrCoalescingExample(XLlTemac * TemacInstancePtr,
XLlDma * DmaInstancePtr)
{
int Status;
u32 TxFrameLength;
int TxFramesToSend = 1000;
int TxFramesSent = 0;
int PayloadSize = XTE_MTU;
u32 Index;
u32 NumBd;
u16 Threshold = 64;
XLlDma_BdRing *RxRingPtr = &XLlDma_mGetRxRing(DmaInstancePtr);
XLlDma_BdRing *TxRingPtr = &XLlDma_mGetTxRing(DmaInstancePtr);
XLlDma_Bd *BdPtr, *BdCurPtr;
/*
* Clear variables shared with callbacks
*/
FramesRx = 0;
FramesTx = 0;
DeviceErrors = 0;
/*
* Calculate the frame length (not including FCS)
*/
TxFrameLength = XTE_HDR_SIZE + PayloadSize;
/*
* Setup packet to be transmitted. The same packet will be transmitted
* over and over
*/
TemacUtilFrameHdrFormatMAC(&TxFrame, TemacMAC);
TemacUtilFrameHdrFormatType(&TxFrame, PayloadSize);
TemacUtilFrameSetPayloadData(&TxFrame, PayloadSize);
/*
* Flush the TX frame before giving it to DMA TX channel to transmit,
* in case D-Caching is turned on.
*/
XCACHE_FLUSH_DCACHE_RANGE(&TxFrame, TxFrameLength);
/*
* We don't care about the receive channel for this example, so turn it off
*/
Status = XLlTemac_ClearOptions(TemacInstancePtr,
XTE_RECEIVER_ENABLE_OPTION);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error clearing option");
return XST_FAILURE;
}
/*
* Set the interrupt coalescing parameters for the test. The waitbound timer
* is set to 1 (ms) to catch the last few frames.
*
* If you set variable Threshold to some value larger than TXBD_CNT, then
* there can never be enough frames sent to meet the threshold. In this case
* the waitbound timer will always cause the interrupt to occur.
*/
Status = XLlDma_BdRingSetCoalesce(TxRingPtr, Threshold, 1);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error setting coalescing settings");
return XST_FAILURE;
}
/*
* Prime the engine, allocate all BDs and assign them to the same buffer
*/
Status = XLlDma_BdRingAlloc(TxRingPtr, TXBD_CNT, &BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error allocating TxBDs prior to starting");
return XST_FAILURE;
}
/*
* Setup the TxBDs
*/
BdCurPtr = BdPtr;
for (Index = 0; Index < TXBD_CNT; Index++) {
XLlDma_mBdSetBufAddr(BdCurPtr, &TxFrame);
XLlDma_mBdSetLength(BdCurPtr, TxFrameLength);
XLlDma_mBdSetStsCtrl(BdCurPtr, XLLDMA_BD_STSCTRL_SOP_MASK |
XLLDMA_BD_STSCTRL_EOP_MASK);
BdCurPtr = XLlDma_mBdRingNext(TxRingPtr, BdCurPtr);
}
/*
* Enqueue all TxBDs to HW
*/
Status = XLlDma_BdRingToHw(TxRingPtr, TXBD_CNT, BdPtr);
TxFramesSent += TXBD_CNT;
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error committing TxBDs prior to starting");
return XST_FAILURE;
}
/*
* Enable the send interrupts. Nothing should be transmitted yet as the
* device has not been started
*/
XLlDma_mBdRingIntEnable(TxRingPtr, XLLDMA_CR_IRQ_ALL_EN_MASK);
/* Enable temac interrupts to capture errors */
XLlTemac_IntEnable(TemacInstancePtr, XTE_INT_RECV_ERROR_MASK);
/*
* Start the device. Transmission commences now!
*/
XLlTemac_Start(TemacInstancePtr);
/*
* As DMA TX channel has been started in
* TemacSgDmaIntrSingleFrameExample() above, there is no need to start
* it again here
*/
while (TxFramesSent < TxFramesToSend) {
/*
* Wait for the interrupt
*/
while (!FramesTx);
/*
* Some TxBDs are ready for post processing. Get all that are available
* at the moment, free them, then allocate the same number and
* re-enqueue back to HW. At the same time this all occurs here,
* the DMA engine should be processing other TxBDs. If we can stay ahead
* of the transmitter like this, then throughput should be at or near
* line-rate.
*
* Note that this retrieves up to TXBD_CNT outstanding packets,
* so we may be processing more packets here than the threshold
* value, which may result in a seemingly spurious interrupt
* next time if we grab twice (or more) of the threshold value
* this time around (clear as mud, eh!). Bottom line is that we
* ignore if NumBd returns as zero.
*/
NumBd = XLlDma_BdRingFromHw(TxRingPtr, TXBD_CNT, &BdPtr);
if (NumBd > 0) {
TxFramesSent += NumBd;
/*
* Don't bother to check the BDs status, just free them
*/
Status = XLlDma_BdRingFree(TxRingPtr, NumBd, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error freeing TxBDs");
}
/*
* Allocate the same number of BDs just freed
*/
Status = XLlDma_BdRingAlloc(TxRingPtr, NumBd, &BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error allocating TxBDs");
return XST_FAILURE;
}
/*
* Setup the TxBDs
*/
BdCurPtr = BdPtr;
for (Index = 0; Index < NumBd; Index++) {
XLlDma_mBdSetBufAddr(BdCurPtr, &TxFrame);
XLlDma_mBdSetLength(BdCurPtr, TxFrameLength);
XLlDma_mBdSetStsCtrl(BdCurPtr,
XLLDMA_BD_STSCTRL_SOP_MASK
|
XLLDMA_BD_STSCTRL_EOP_MASK);
BdCurPtr =
XLlDma_mBdRingNext(TxRingPtr, BdCurPtr);
}
/*
* Enqueue TxBDs to HW
*/
Status = XLlDma_BdRingToHw(TxRingPtr, NumBd, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap
("Error committing TxBDs prior to starting");
return XST_FAILURE;
}
}
/*
* Re-enable the interrupts
*/
FramesTx = 0;
XLlDma_mBdRingIntEnable(TxRingPtr, XLLDMA_CR_IRQ_ALL_EN_MASK);
}
/*
* Wait a second and collect any remaining frames that had been
* queued up but not post processed
*/
#ifndef __MICROBLAZE__
usleep(1000000);
#else
/*
* Not sure if we should depend on there being a timer core in a
* microblaze system
*/
TemacUtilPhyDelay(1);
#endif
NumBd = XLlDma_BdRingFromHw(TxRingPtr, 0xFFFFFFFF, &BdPtr);
if (NumBd > 0) {
Status = XLlDma_BdRingFree(TxRingPtr, NumBd, BdPtr);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error freeing TxBDs");
}
}
/*
* Done sending frames. Stop the device
*/
XLlTemac_Stop(TemacInstancePtr);
return XST_SUCCESS;
}
/**
*
* This example uses polled mode to queue up multiple frames in the packet
* FIFOs before sending them in a single burst. Receive packets are handled in
* a similar way.
*
* @param None.
*
* @return XST_SUCCESS to indicate success, otherwise XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int TemacMultipleFramesPolledExample(void)
{
u32 FramesToLoopback;
u32 PayloadSize;
u32 TxFrameLength;
u32 RxFrameLength;
u32 FifoFreeBytes;
u32 Index;
/*
* Start the TEMAC device
*/
XLlTemac_Start(&TemacInstance);
/*
* Setup the number of frames to loopback (FramesToLoopback) and the size
* of the frame (PayloadSize) to loopback. The default settings should
* work for every case. Modifying the settings can cause problems, see
* discussion below:
*
* If PayloadSize is set small and FramesToLoopback high, then it is
* possible to cause the transmit status FIFO to overflow.
*
* If PayloadSize is set large and FramesToLoopback high, then it is
* possible to cause the transmit packet FIFO to overflow.
*
* Either of these scenarios may be worth trying out to observe how the
* driver reacts. The exact values to cause these types of errors
* will vary due to the sizes of the FIFOs selected at hardware build
* time. But the following settings should create problems for all
* FIFO sizes:
*
* Transmit status FIFO overflow
* PayloadSize = 1
* FramesToLoopback = 1000
*
* Transmit packet FIFO overflow
* PayloadSize = 1500
* FramesToLoopback = 16
*
* These values should always work without error
* PayloadSize = 100
* FramesToLoopback = 5
*/
PayloadSize = 100;
FramesToLoopback = 5;
/*
* Calculate Tx frame length (not including FCS)
*/
TxFrameLength = XTE_HDR_SIZE + PayloadSize;
/*
* Setup the packet to be transmitted
*/
TemacUtilFrameHdrFormatMAC(&TxFrame, TemacMAC);
TemacUtilFrameHdrFormatType(&TxFrame, PayloadSize);
TemacUtilFrameSetPayloadData(&TxFrame, PayloadSize);
/****************/
/* Send packets */
/****************/
/*
* Since we may be interested to see what happens when FIFOs overflow, don't
* check for room in the transmit packet FIFO prior to writing to it.
*/
/*
* Write frame data to FIFO
* Fifo core only allows loading and sending one frame at a time.
*/
for (Index = 0; Index < FramesToLoopback; Index++) {
/* Make sure there is room in the FIFO */
do {
FifoFreeBytes = XLlFifo_TxVacancy(&FifoInstance);
} while (FifoFreeBytes < TxFrameLength);
XLlFifo_Write(&FifoInstance, TxFrame, TxFrameLength);
XLlFifo_TxSetLen(&FifoInstance, TxFrameLength);
switch (TemacPollForTxStatus()) {
case XST_SUCCESS: /* Got a sucessfull transmit status */
break;
case XST_NO_DATA: /* Timed out */
TemacUtilErrorTrap("Tx timeout");
return XST_FAILURE;
break;
default: /* Some other error */
TemacResetDevice();
return XST_FAILURE;
}
}
/**********************/
/* Receive the packet */
/**********************/
/*
* Wait for the packets to arrive
* The Fifo core only allows us to pull out one frame at a time.
*/
for (Index = 0; Index < FramesToLoopback; Index++) {
/*
* Wait for packet Rx
*/
switch (TemacPollForRxStatus()) {
case XST_SUCCESS: /* Got a successfull receive status */
break;
case XST_NO_DATA: /* Timed out */
TemacUtilErrorTrap("Rx timeout");
return XST_FAILURE;
break;
default: /* Some other error */
TemacResetDevice();
return XST_FAILURE;
}
while(XLlFifo_RxOccupancy(&FifoInstance)) {
/*
* A packet has arrived, get its length
*/
RxFrameLength = XLlFifo_RxGetLen(&FifoInstance);
/*
* Verify the received frame length
*/
if ((RxFrameLength) != TxFrameLength) {
TemacUtilErrorTrap("Receive length incorrect");
return XST_FAILURE;
}
/*
* Read the received packet data
*/
XLlFifo_Read(&FifoInstance, &RxFrame, RxFrameLength);
if (TemacUtilFrameVerify(&TxFrame, &RxFrame) != 0) {
TemacUtilErrorTrap("Receive Data Mismatch");
return XST_FAILURE;
}
}
}
/*
* Stop device
*/
XLlTemac_Stop(&TemacInstance);
return XST_SUCCESS;
}
/**
*
* This function demonstrates the usage of the TEMAC by sending and receiving
* a single frame in polled mode.
*
* @param None.
*
* @return XST_SUCCESS to indicate success, otherwise XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int TemacSingleFramePolledExample(void)
{
u32 FifoFreeBytes;
int PayloadSize = 100;
u32 TxFrameLength;
u32 RxFrameLength;
/*
* Start the TEMAC device
*/
XLlTemac_Start(&TemacInstance);
/*
* Setup the packet to be transmitted
*/
TemacUtilFrameHdrFormatMAC(&TxFrame, TemacMAC);
TemacUtilFrameHdrFormatType(&TxFrame, PayloadSize);
TemacUtilFrameSetPayloadData(&TxFrame, PayloadSize);
/*
* Clear out the receive packet memory area
*/
TemacUtilFrameMemClear(&RxFrame);
/*
* Calculate frame length (not including FCS)
*/
TxFrameLength = XTE_HDR_SIZE + PayloadSize;
/*******************/
/* Send the packet */
/*******************/
/*
* Wait for enough room in FIFO to become available
*/
do {
FifoFreeBytes = XLlFifo_TxVacancy(&FifoInstance);
} while (FifoFreeBytes < TxFrameLength);
/*
* Write the frame data to FIFO
*/
XLlFifo_Write(&FifoInstance, TxFrame, TxFrameLength);
/*
* Initiate transmit
*/
XLlFifo_TxSetLen(&FifoInstance, TxFrameLength);
/*
* Wait for status of the transmitted packet
*/
switch (TemacPollForTxStatus()) {
case XST_SUCCESS: /* Got a sucessfull transmit status */
break;
case XST_NO_DATA: /* Timed out */
TemacUtilErrorTrap("Tx timeout");
return XST_FAILURE;
default: /* Some other error */
return XST_FAILURE;
}
/**********************/
/* Receive the packet */
/**********************/
/*
* Wait for packet Rx
*/
switch (TemacPollForRxStatus()) {
case XST_SUCCESS: /* Got a sucessfull receive status */
break;
case XST_NO_DATA: /* Timed out */
TemacUtilErrorTrap("Rx timeout");
return XST_FAILURE;
default: /* Some other error */
return XST_FAILURE;
}
while(XLlFifo_RxOccupancy(&FifoInstance)) {
/*
* A packet as arrived, get its length
*/
RxFrameLength = XLlFifo_RxGetLen(&FifoInstance);
/*
* Read the received packet data
*/
XLlFifo_Read(&FifoInstance, &RxFrame, RxFrameLength);
/*
* Verify the received frame length
*/
if ((RxFrameLength) != TxFrameLength) {
TemacUtilErrorTrap("Receive length incorrect");
return XST_FAILURE;
}
/*
* Validate frame data
*/
if (TemacUtilFrameVerify(&TxFrame, &RxFrame) != 0) {
TemacUtilErrorTrap("Receive Data mismatch");
return XST_FAILURE;
}
}
/*
* Stop device
*/
XLlTemac_Stop(&TemacInstance);
return XST_SUCCESS;
}