void tmr0_isr(void) {
if(bit_is_set(*TMR(0,CSCTRL),TCF1)) {
current_clock++;
if((current_clock % CLOCK_CONF_SECOND) == 0) {
seconds++;
/* ADC can be serviced every tick or every second */
#if CLOCK_CONF_SAMPLEADC > 1
adc_service();
#endif
}
#if CLOCK_CONF_SAMPLEADC == 1
adc_service();
#endif
if(etimer_pending() &&
(etimer_next_expiration_time() - current_clock - 1) > MAX_TICKS) {
etimer_request_poll();
}
/* clear the compare flags */
clear_bit(*TMR(0,SCTRL),TCF);
clear_bit(*TMR(0,CSCTRL),TCF1);
clear_bit(*TMR(0,CSCTRL),TCF2);
return;
} else {
/* this timer didn't create an interrupt condition */
return;
}
}
void
clock_init()
{
/* timer setup */
/* CTRL */
#define COUNT_MODE 1 /* use rising edge of primary source */
#define PRIME_SRC 0xf /* Perip. clock with 128 prescale (for 24Mhz = 187500Hz)*/
#define SEC_SRC 0 /* don't need this */
#define ONCE 0 /* keep counting */
#define LEN 1 /* count until compare then reload with value in LOAD */
#define DIR 0 /* count up */
#define CO_INIT 0 /* other counters cannot force a re-initialization of this counter */
#define OUT_MODE 0 /* OFLAG is asserted while counter is active */
*TMR_ENBL = 0; /* tmrs reset to enabled */
*TMR0_SCTRL = 0;
*TMR0_CSCTRL =0x0040;
*TMR0_LOAD = 0; /* reload to zero */
*TMR0_COMP_UP = 1875; /* trigger a reload at the end */
*TMR0_CMPLD1 = 1875; /* compare 1 triggered reload level, 10HZ maybe? */
*TMR0_CNTR = 0; /* reset count register */
*TMR0_CTRL = (COUNT_MODE<<13) | (PRIME_SRC<<9) | (SEC_SRC<<7) | (ONCE<<6) | (LEN<<5) | (DIR<<4) | (CO_INIT<<3) | (OUT_MODE);
*TMR_ENBL = 0xf; /* enable all the timers --- why not? */
enable_irq(TMR);
/* Do startup scan of the ADC */
#if CLOCK_CONF_SAMPLEADC
adc_reading[8]=0;
adc_init();
while (adc_reading[8]==0) adc_service();
#endif
}
static int poti_value(int type)
{
uint16_t result = 0;
uint8_t counter = 0;
global_irq_disable();
while(counter < 254)
{
adc_service();
result = adc_voltage(ADC_PIN);
counter++;
clock_delay_usec( 33 );
}
global_irq_enable();
return result;
}
/*---------------------------------------------------------------------------*/
static
PT_THREAD(ajax_call(struct httpd_state *s, char *ptr))
{
static struct timer t;
static int iter;
static char buf[128];
static uint8_t numprinted;
PSOCK_BEGIN(&s->sout);
/*TODO:pick up time from ? parameter */
timer_set(&t, 2*CLOCK_SECOND);
iter = 0;
while(1) {
iter++;
#if CONTIKI_TARGET_SKY
SENSORS_ACTIVATE(sht11_sensor);
SENSORS_ACTIVATE(light_sensor);
numprinted = snprintf(buf, sizeof(buf),
"t(%d);h(%d);l1(%d);l2(%d);",
sht11_sensor.value(SHT11_SENSOR_TEMP),
sht11_sensor.value(SHT11_SENSOR_HUMIDITY),
light_sensor.value(LIGHT_SENSOR_PHOTOSYNTHETIC),
light_sensor.value(LIGHT_SENSOR_TOTAL_SOLAR));
SENSORS_DEACTIVATE(sht11_sensor);
SENSORS_DEACTIVATE(light_sensor);
#elif CONTIKI_TARGET_MB851
SENSORS_ACTIVATE(acc_sensor);
numprinted = snprintf(buf, sizeof(buf),"t(%d);ax(%d);ay(%d);az(%d);",
temperature_sensor.value(0),
acc_sensor.value(ACC_X_AXIS),
acc_sensor.value(ACC_Y_AXIS),
acc_sensor.value(ACC_Z_AXIS));
SENSORS_DEACTIVATE(acc_sensor);
#elif CONTIKI_TARGET_REDBEE_ECONOTAG
{ uint8_t c;
adc_reading[8]=0;
adc_init();
while (adc_reading[8]==0) adc_service();
adc_disable();
numprinted = snprintf(buf, sizeof(buf),"b(%u);adc(%u,%u,%u,%u,%u,%u,%u,%u);",
1200*0xfff/adc_reading[8],adc_reading[0],adc_reading[1],adc_reading[2],adc_reading[3],adc_reading[4],adc_reading[5],adc_reading[6],adc_reading[7]);
}
#elif CONTIKI_TARGET_MINIMAL_NET
static uint16_t c0=0x3ff,c1=0x3ff,c2=0x3ff,c3=0x3ff,c4=0x3ff,c5=0x3ff,c6=0x3ff,c7=0x3ff;
numprinted = snprintf(buf, sizeof(buf), "t(%d);b(%u);v(%u);",273+(rand()&0x3f),3300-iter/10,iter);
numprinted += snprintf(buf+numprinted, sizeof(buf)-numprinted,"adc(%u,%u,%u,%u,%u,%u,%u,%u);",c0,c1,c2,c3,c4,c5,c6,c7);
c0+=(rand()&0xf)-8;
c1+=(rand()&0xf)-8;
c2+=(rand()&0xf)-7;
c3+=(rand()&0x1f)-15;
c4+=(rand()&0x3)-1;
c5+=(rand()&0xf)-8;
c6+=(rand()&0xf)-8;
c7+=(rand()&0xf)-8;
if (iter==1) {
static const char httpd_cgi_ajax11[] HTTPD_STRING_ATTR = "wt('Minimal-net ";
static const char httpd_cgi_ajax12[] HTTPD_STRING_ATTR = "');";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax11);
#if WEBSERVER_CONF_PRINTADDR
/* Note address table is filled from the end down */
{int i;
for (i=0; i<UIP_DS6_ADDR_NB;i++) {
if (uip_ds6_if.addr_list[i].isused) {
numprinted += httpd_cgi_sprint_ip6(uip_ds6_if.addr_list[i].ipaddr, buf + numprinted);
break;
}
}
}
#endif
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax12);
}
#elif CONTIKI_TARGET_AVR_ATMEGA128RFA1
{ uint8_t i;int16_t tmp,bat;
BATMON = 16; //give BATMON time to stabilize at highest range and lowest voltage
/* Measure internal temperature sensor, see atmega128rfa1 datasheet */
/* This code disabled by default for safety.
Selecting an internal reference will short it to anything connected to the AREF pin
*/
#if 1
ADCSRB|=1<<MUX5; //this bit buffered till ADMUX written to!
ADMUX =0xc9; // Select internal 1.6 volt ref, temperature sensor ADC channel
ADCSRA=0x85; //Enable ADC, not free running, interrupt disabled, clock divider 32 (250 KHz@ 8 MHz)
// while ((ADCSRB&(1<<AVDDOK))==0); //wait for AVDD ok
// while ((ADCSRB&(1<<REFOK))==0); //wait for ref ok
ADCSRA|=1<<ADSC; //Start throwaway conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
ADCSRA|=1<<ADSC; //Start another conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
tmp=ADC; //Read adc
tmp=11*tmp-2728+(tmp>>2); //Convert to celcius*10 (should be 11.3*h, approximate with 11.25*h)
ADCSRA=0; //disable ADC
ADMUX=0; //turn off internal vref
#endif
/* Bandgap can't be measured against supply voltage in this chip. */
/* Use BATMON register instead */
for ( i=16; i<31; i++) {
BATMON = i;
if ((BATMON&(1<<BATMON_OK))==0) break;
}
bat=2550-75*16-75+75*i; //-75 to take the floor of the 75 mv transition window
static const char httpd_cgi_ajax10[] HTTPD_STRING_ATTR ="t(%u),b(%u);adc(%d,%d,%u,%u,%u,%u,%u,%lu);";
numprinted = httpd_snprintf(buf, sizeof(buf),httpd_cgi_ajax10,tmp,bat,iter,tmp,bat,sleepcount,OCR2A,0,clock_time(),clock_seconds());
if (iter==1) {
static const char httpd_cgi_ajax11[] HTTPD_STRING_ATTR = "wt('128rfa1 [";
static const char httpd_cgi_ajax12[] HTTPD_STRING_ATTR = "]');";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax11);
#if WEBSERVER_CONF_PRINTADDR
/* Note address table is filled from the end down */
{int i;
for (i=0; i<UIP_DS6_ADDR_NB;i++) {
if (uip_ds6_if.addr_list[i].isused) {
numprinted += httpd_cgi_sprint_ip6(uip_ds6_if.addr_list[i].ipaddr, buf + numprinted);
break;
}
}
}
#endif
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax12);
}
}
#elif CONTIKI_TARGET_AVR_RAVEN
{ int16_t tmp,bat;
#if 1
/* Usual way to get AVR supply voltage, measure 1.1v bandgap using Vcc as reference.
* This connects the bandgap to the AREF pin, so enable only if there is no external AREF!
* A capacitor may be connected to this pin to reduce reference noise.
*/
ADMUX =0x5E; //Select AVCC as reference, measure 1.1 volt bandgap reference.
ADCSRA=0x87; //Enable ADC, not free running, interrupt disabled, clock divider 128 (62 KHz@ 8 MHz)
ADCSRA|=1<<ADSC; //Start throwaway conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
ADCSRA|=1<<ADSC; //Start another conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
//bat=1126400UL/ADC; //Get supply voltage (factor nominally 1100*1024)
bat=1198070UL/ADC; //My Raven
ADCSRA=0; //disable ADC
ADMUX=0; //turn off internal vref
#else
bat=3300;
#endif
tmp=420;
static const char httpd_cgi_ajax10[] HTTPD_STRING_ATTR ="t(%u),b(%u);adc(%d,%d,%u,%u,%u,%u,%u,%lu);";
numprinted = httpd_snprintf(buf, sizeof(buf),httpd_cgi_ajax10,tmp,bat,iter,tmp,bat,sleepcount,OCR2A,0,clock_time(),clock_seconds());
if (iter<3) {
static const char httpd_cgi_ajax11[] HTTPD_STRING_ATTR = "wt('Raven [";
static const char httpd_cgi_ajax12[] HTTPD_STRING_ATTR = "]');";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax11);
#if WEBSERVER_CONF_PRINTADDR
/* Note address table is filled from the end down */
{int i;
for (i=0; i<UIP_DS6_ADDR_NB;i++) {
if (uip_ds6_if.addr_list[i].isused) {
numprinted += httpd_cgi_sprint_ip6(uip_ds6_if.addr_list[i].ipaddr, buf + numprinted);
break;
}
}
}
#endif
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax12);
}
}
//#elif CONTIKI_TARGET_IS_SOMETHING_ELSE
#else
{
static const char httpd_cgi_ajax10[] HTTPD_STRING_ATTR ="v(%u);";
numprinted = httpd_snprintf(buf, sizeof(buf),httpd_cgi_ajax10,iter);
if (iter==1) {
static const char httpd_cgi_ajax11[] HTTPD_STRING_ATTR = "wt('Contiki Ajax ";
static const char httpd_cgi_ajax12[] HTTPD_STRING_ATTR = "');";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax11);
#if WEBSERVER_CONF_PRINTADDR
/* Note address table is filled from the end down */
{int i;
for (i=0; i<UIP_DS6_ADDR_NB;i++) {
if (uip_ds6_if.addr_list[i].isused) {
numprinted += httpd_cgi_sprint_ip6(uip_ds6_if.addr_list[i].ipaddr, buf + numprinted);
break;
}
}
}
#endif
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajax12);
}
}
#endif
#if CONTIKIMAC_CONF_COMPOWER
#include "sys/compower.h"
{
//sl=compower_idle_activity.transmit/RTIMER_ARCH_SECOND;
//sl=compower_idle_activity.listen/RTIMER_ARCH_SECOND;
}
#endif
#if RIMESTATS_CONF_ON
#include "net/rime/rimestats.h"
static const char httpd_cgi_ajaxr1[] HTTPD_STRING_ATTR ="rime(%lu,%lu,%lu,%lu);";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajaxr1,
rimestats.tx,rimestats.rx,rimestats.lltx-rimestats.tx,rimestats.llrx-rimestats.rx);
#endif
#if ENERGEST_CONF_ON
{
#if 1
/* Send on times in percent since last update. Handle 16 bit rtimer wraparound. */
/* Javascript must convert based on platform cpu, tx, rx power, e.g. 20ma*3v3=66mW*(% on time/100) */
static rtimer_clock_t last_send;
rtimer_clock_t delta_time;
static unsigned long last_cpu, last_lpm, last_listen, last_transmit;
energest_flush();
delta_time=RTIMER_NOW()-last_send;
if (RTIMER_CLOCK_LT(RTIMER_NOW(),last_send)) delta_time+=RTIMER_ARCH_SECOND;
last_send=RTIMER_NOW();
static const char httpd_cgi_ajaxe1[] HTTPD_STRING_ATTR = "p(%lu,%lu,%lu,%lu);";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajaxe1,
(100UL*(energest_total_time[ENERGEST_TYPE_CPU].current - last_cpu))/delta_time,
(100UL*(energest_total_time[ENERGEST_TYPE_LPM].current - last_lpm))/delta_time,
(100UL*(energest_total_time[ENERGEST_TYPE_TRANSMIT].current - last_transmit))/delta_time,
(100UL*(energest_total_time[ENERGEST_TYPE_LISTEN].current - last_listen))/delta_time);
last_cpu = energest_total_time[ENERGEST_TYPE_CPU].current;
last_lpm = energest_total_time[ENERGEST_TYPE_LPM].current;
last_transmit = energest_total_time[ENERGEST_TYPE_TRANSMIT].current;
last_listen = energest_total_time[ENERGEST_TYPE_LISTEN].current;
#endif
#if 1
/* Send cumulative on times in percent*100 */
uint16_t cpp,txp,rxp;
uint32_t sl,clockseconds=clock_seconds();
// energest_flush();
// sl=((10000UL*energest_total_time[ENERGEST_TYPE_CPU].current)/RTIMER_ARCH_SECOND)/clockseconds;
sl=energest_total_time[ENERGEST_TYPE_CPU].current/RTIMER_ARCH_SECOND;
cpp=(10000UL*sl)/clockseconds;
// txp=((10000UL*energest_total_time[ENERGEST_TYPE_TRANSMIT].current)/RTIMER_ARCH_SECOND)/clockseconds;
sl=energest_total_time[ENERGEST_TYPE_TRANSMIT].current/RTIMER_ARCH_SECOND;
txp=(10000UL*sl)/clockseconds;
// rxp=((10000UL*energest_total_time[ENERGEST_TYPE_LISTEN].current)/RTIMER_ARCH_SECOND)/clockseconds;
sl=energest_total_time[ENERGEST_TYPE_LISTEN].current/RTIMER_ARCH_SECOND;
rxp=(10000UL*sl)/clockseconds;
static const char httpd_cgi_ajaxe2[] HTTPD_STRING_ATTR = "ener(%u,%u,%u);";
numprinted += httpd_snprintf(buf+numprinted, sizeof(buf)-numprinted,httpd_cgi_ajaxe2,cpp,txp,rxp);
#endif
}
#endif /* ENERGEST_CONF_ON */
PSOCK_SEND_STR(&s->sout, buf);
timer_restart(&t);
PSOCK_WAIT_UNTIL(&s->sout, timer_expired(&t));
}
PSOCK_END(&s->sout);
}
/*---------------------------------------------------------------------------*/
static unsigned short
generate_sensor_readings(void *arg)
{
uint16_t numprinted;
uint16_t days,h,m,s;
unsigned long seconds=clock_seconds();
static const char httpd_cgi_sensor0[] HTTPD_STRING_ATTR = "[Updated %d seconds ago]<br><br>";
static const char httpd_cgi_sensor1[] HTTPD_STRING_ATTR = "<pre><em>Temperature:</em> %s\n";
static const char httpd_cgi_sensor2[] HTTPD_STRING_ATTR = "<em>Battery :</em> %s\n";
// static const char httpd_cgi_sensr12[] HTTPD_STRING_ATTR = "<em>Temperature:</em> %s <em>Battery:</em> %s<br>";
static const char httpd_cgi_sensor3[] HTTPD_STRING_ATTR = "<em>Uptime :</em> %02d:%02d:%02d\n";
static const char httpd_cgi_sensor3d[] HTTPD_STRING_ATTR = "<em>Uptime :</em> %u days %02u:%02u:%02u/n";
// static const char httpd_cgi_sensor4[] HTTPD_STRING_ATTR = "<em>Sleeping time :</em> %02d:%02d:%02d (%d%%)<br>";
numprinted=0;
/* Generate temperature and voltage strings for each platform */
#if CONTIKI_TARGET_AVR_ATMEGA128RFA1
{uint8_t i;
BATMON = 16; //give BATMON time to stabilize at highest range and lowest voltage
/* Measure internal temperature sensor, see atmega128rfa1 datasheet */
/* This code disabled by default for safety.
Selecting an internal reference will short it to anything connected to the AREF pin
*/
#if 0
ADCSRB|=1<<MUX5; //this bit buffered till ADMUX written to!
ADMUX =0xc9; // Select internal 1.6 volt ref, temperature sensor ADC channel
ADCSRA=0x85; //Enable ADC, not free running, interrupt disabled, clock divider 32 (250 KHz@ 8 MHz)
// while ((ADCSRB&(1<<AVDDOK))==0); //wait for AVDD ok
// while ((ADCSRB&(1<<REFOK))==0); //wait for ref ok
ADCSRA|=1<<ADSC; //Start throwaway conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
ADCSRA|=1<<ADSC; //Start another conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
h=ADC; //Read adc
h=11*h-2728+(h>>2); //Convert to celcius*10 (should be 11.3*h, approximate with 11.25*h)
ADCSRA=0; //disable ADC
ADMUX=0; //turn off internal vref
m=h/10;s=h-10*m;
static const char httpd_cgi_sensor1_printf[] HTTPD_STRING_ATTR = "%d.%d C";
httpd_snprintf(sensor_temperature,sizeof(sensor_temperature),httpd_cgi_sensor1_printf,m,s);
#endif
/* Bandgap can't be measured against supply voltage in this chip. */
/* Use BATMON register instead */
for ( i=16; i<31; i++) {
BATMON = i;
if ((BATMON&(1<<BATMON_OK))==0) break;
}
h=2550-75*16-75+75*i; //-75 to take the floor of the 75 mv transition window
static const char httpd_cgi_sensor2_printf[] HTTPD_STRING_ATTR = "%u mv";
httpd_snprintf(sensor_extvoltage,sizeof(sensor_extvoltage),httpd_cgi_sensor2_printf,h);
}
#elif CONTIKI_TARGET_AVR_RAVEN
{
#if 1
/* Usual way to get AVR supply voltage, measure 1.1v bandgap using Vcc as reference.
* This connects the bandgap to the AREF pin, so enable only if there is no external AREF!
* A capacitor may be connected to this pin to reduce reference noise.
*/
ADMUX =0x5E; //Select AVCC as reference, measure 1.1 volt bandgap reference.
ADCSRA=0x87; //Enable ADC, not free running, interrupt disabled, clock divider 128 (62 KHz@ 8 MHz)
ADCSRA|=1<<ADSC; //Start throwaway conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
ADCSRA|=1<<ADSC; //Start another conversion
while (ADCSRA&(1<<ADSC)); //Wait till done
//h=1126400UL/ADC; //Get supply voltage (factor nominally 1100*1024)
h=1198070UL/ADC; //My Raven
ADCSRA=0; //disable ADC
ADMUX=0; //turn off internal vref
static const char httpd_cgi_sensor2_printf[] HTTPD_STRING_ATTR = "%u mv";
httpd_snprintf(sensor_extvoltage,sizeof(sensor_extvoltage),httpd_cgi_sensor2_printf,h);
#endif
}
#elif CONTIKI_TARGET_REDBEE_ECONOTAG
//#include "adc.h"
{
uint8_t c;
adc_reading[8]=0;
adc_init();
while (adc_reading[8]==0) adc_service();
// for (c=0; c<NUM_ADC_CHAN; c++) printf("%u %04u\r\n", c, adc_reading[c]);
adc_disable();
snprintf(sensor_extvoltage, sizeof(sensor_extvoltage),"%u mV",1200*0xfff/adc_reading[8]);
static const char httpd_cgi_sensorv[] HTTPD_STRING_ATTR = "<em>ADC chans :</em> %u %u %u %u %u %u %u %u \n";
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensorv,
adc_reading[0],adc_reading[1],adc_reading[2],adc_reading[3],adc_reading[4],adc_reading[5],adc_reading[6],adc_reading[7]);
}
#endif
if (last_tempupdate) {
numprinted =httpd_snprintf((char *)uip_appdata, uip_mss(), httpd_cgi_sensor0,(unsigned int) (seconds-last_tempupdate));
}
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor1, sensor_temperature);
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor2, sensor_extvoltage);
// numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensr12, sensor_temperature,sensor_extvoltage);
#if RADIOSTATS
/* Remember radioontime for display below - slow connection might make it report longer than cpu ontime! */
savedradioontime = radioontime;
#endif
h=seconds/3600;s=seconds-h*3600;m=s/60;s=s-m*60;
days=h/24;
if (days == 0) {
numprinted+=httpd_snprintf((char *)uip_appdata + numprinted, uip_mss() - numprinted, httpd_cgi_sensor3, h,m,s);
} else {
h=h-days*24;
numprinted+=httpd_snprintf((char *)uip_appdata + numprinted, uip_mss() - numprinted, httpd_cgi_sensor3d, days,h,m,s);
}
#if 0
if (sleepseconds) {
uint8_t p1;
p1=100UL*sleepseconds/seconds;h=sleepseconds/3600;s=sleepseconds-h*3600;m=s/60;s=s-m*60;
numprinted+=httpd_snprintf((char *)uip_appdata + numprinted, uip_mss() - numprinted, httpd_cgi_sensor4, h,m,s,p1);
}
#endif
#if ENERGEST_CONF_ON
{uint8_t p1,p2;
uint32_t sl;
#if 0
/* Update all the timers to get current values */
for (p1=1;p1<ENERGEST_TYPE_MAX;p1++) {
if (energest_current_mode[p1]) {
ENERGEST_OFF(p1);
ENERGEST_ON(p1);
}
}
#else
energest_flush();
#endif
static const char httpd_cgi_sensor4[] HTTPD_STRING_ATTR = "<em>CPU time (ENERGEST):</em> %02u:%02u:%02u (%u.%02u%%)\n";
static const char httpd_cgi_sensor10[] HTTPD_STRING_ATTR = "<em>Radio (ENERGEST):</em> Tx %02u:%02u:%02u (%u.%02u%%) ";
static const char httpd_cgi_sensor11[] HTTPD_STRING_ATTR = "Rx %02u:%02u:%02u (%u.%02u%%)\n";
sl=energest_total_time[ENERGEST_TYPE_CPU].current/RTIMER_ARCH_SECOND;
h=(10000UL*sl)/seconds;p1=h/100;p2=h-p1*100;h=sl/3600;s=sl-h*3600;m=s/60;s=s-m*60;
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor4, h,m,s,p1,p2);
sl=energest_total_time[ENERGEST_TYPE_TRANSMIT].current/RTIMER_ARCH_SECOND;
h=(10000UL*sl)/seconds;p1=h/100;p2=h-p1*100;h=sl/3600;s=sl-h*3600;m=s/60;s=s-m*60;
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor10, h,m,s,p1,p2);
sl=energest_total_time[ENERGEST_TYPE_LISTEN].current/RTIMER_ARCH_SECOND;
h=(10000UL*sl)/seconds;p1=h/100;p2=h-p1*100;h=sl/3600;s=sl-h*3600;m=s/60;s=s-m*60;
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor11, h,m,s,p1,p2);
}
#endif /* ENERGEST_CONF_ON */
#if CONTIKIMAC_CONF_COMPOWER
#include "sys/compower.h"
{uint8_t p1,p2;
// extern struct compower_activity current_packet;
static const char httpd_cgi_sensor31[] HTTPD_STRING_ATTR = "<em>ContikiMAC (COMPOWER):</em> Tx %02u:%02u:%02u (%u.%02u%%) ";
static const char httpd_cgi_sensor32[] HTTPD_STRING_ATTR = "Rx %02u:%02u:%02u (%u.%02u%%)\n";
s=compower_idle_activity.transmit/RTIMER_ARCH_SECOND;
h=((10000UL*compower_idle_activity.transmit)/RTIMER_ARCH_SECOND)/seconds;
p1=h/100;p2=h-p1*100;h=s/3600;s=s-h*3600;m=s/60;s=s-m*60;
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor31, h,m,s,p1,p2);
s=compower_idle_activity.listen/RTIMER_ARCH_SECOND;
h=((10000UL*compower_idle_activity.listen)/RTIMER_ARCH_SECOND)/seconds;
p1=h/100;p2=h-p1*100;h=s/3600;s=s-h*3600;m=s/60;s=s-m*60;
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor32, h,m,s,p1,p2);
}
#endif
#if RIMESTATS_CONF_ON
#include "net/rime/rimestats.h"
static const char httpd_cgi_sensor21[] HTTPD_STRING_ATTR = "<em>Packets (RIMESTATS):</em> Tx=%5lu Rx=%5lu TxL=%4lu RxL=%4lu\n";
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor21,
rimestats.tx,rimestats.rx,rimestats.lltx-rimestats.tx,rimestats.llrx-rimestats.rx);
#endif
static const char httpd_cgi_sensor99[] HTTPD_STRING_ATTR = "</pre>";
numprinted+=httpd_snprintf((char *)uip_appdata+numprinted, uip_mss()-numprinted, httpd_cgi_sensor99);
return numprinted;
}