Exemplo n.º 1
0
int ag7240_enet_initialize(bd_t * bis) {
	struct eth_device *dev[CFG_AG7240_NMACS];
	u32 mask, mac_h, mac_l;
	int i;

#ifdef AG7240_DEBUG
	printf("ag7240_enet_initialize...\n");
#endif

	// TODO check this register!
	ar7240_reg_wr(HORNET_BOOTSTRAP_STATUS, ar7240_reg_rd(HORNET_BOOTSTRAP_STATUS) & ~HORNET_BOOTSTRAP_MDIO_SLAVE_MASK);

	if (is_ar933x()) {
		u32 rd = 0x0;

		/* 
		 * To get s26 out of reset, we have to...
		 * bit0~bit3: has to be deasserted
		 * bit4:      has to be asserted
		 */
		rd = ar7240_reg_rd(AR7240_S26_CLK_CTRL_OFFSET) & ~(0x1f);
		rd |= 0x10;
		ar7240_reg_wr(AR7240_S26_CLK_CTRL_OFFSET, rd);

		if (ar7240_reg_rd(AR7240_RESET) != 0) {
			ar7240_reg_wr(AR7240_RESET, 0);
		}
	}

	for (i = 0; i < CFG_AG7240_NMACS; i++) {

		if ((dev[i] = (struct eth_device *) malloc(sizeof(struct eth_device))) == NULL) {
			puts("## Error: malloc failed\n");
			return 0;
		}

		if ((ag7240_macs[i] = (ag7240_mac_t *) malloc(sizeof(ag7240_mac_t))) == NULL) {
			puts("## Error: malloc failed\n");
			return 0;
		}

		memset(ag7240_macs[i], 0, sizeof(ag7240_macs[i]));
		memset(dev[i], 0, sizeof(dev[i]));

		sprintf(dev[i]->name, "eth%d", i);
		ag7240_get_ethaddr(dev[i]);

		ag7240_macs[i]->mac_unit = i;
		ag7240_macs[i]->mac_base = i ? AR7240_GE1_BASE : AR7240_GE0_BASE;
		ag7240_macs[i]->dev = dev[i];

		dev[i]->iobase = 0;
		dev[i]->init = ag7240_clean_rx;
		dev[i]->halt = ag7240_halt;
		dev[i]->send = ag7240_send;
		dev[i]->recv = ag7240_recv;
		dev[i]->priv = (void *) ag7240_macs[i];
	}

	for (i = 0; i < CFG_AG7240_NMACS; i++) {

		eth_register(dev[i]);

#if(CONFIG_COMMANDS & CFG_CMD_MII)
		miiphy_register(dev[i]->name, ag7240_miiphy_read, ag7240_miiphy_write);
#endif

		ag7240_reg_rmw_set(ag7240_macs[i], AG7240_MAC_CFG1, AG7240_MAC_CFG1_SOFT_RST | AG7240_MAC_CFG1_RX_RST | AG7240_MAC_CFG1_TX_RST);

		if (!i) {
			mask = (AR7240_RESET_GE0_MAC | AR7240_RESET_GE0_PHY | AR7240_RESET_GE1_MAC | AR7240_RESET_GE1_PHY);

			if (is_ar7241() || is_ar7242() || is_wasp()){
				mask = mask | AR7240_RESET_GE0_MDIO | AR7240_RESET_GE1_MDIO;
			}

			ar7240_reg_rmw_set(AR7240_RESET, mask);

			if (!is_ar933x()){
				udelay(1000 * 100);
			}

			ar7240_reg_rmw_clear(AR7240_RESET, mask);

			if (!is_ar933x()){
				udelay(1000 * 100);
			}

			if (!is_ar933x()){
				udelay(10 * 1000);
			}
		}

		ag7240_hw_start(ag7240_macs[i]);

		ag7240_setup_fifos(ag7240_macs[i]);

		if (!is_ar933x()){
			udelay(100 * 1000);
		}

#ifdef AG7240_DEBUG
		unsigned char *mac = dev[i]->enetaddr;
		printf("\nInterface %s MAC address: %02X:%02X:%02X:%02X:%02X:%02X\n", dev[i]->name, mac[0] & 0xff, mac[1] & 0xff, mac[2] & 0xff, mac[3] & 0xff, mac[4] & 0xff, mac[5] & 0xff);
#endif

		mac_l = (dev[i]->enetaddr[4] << 8) | (dev[i]->enetaddr[5]);
		mac_h = (dev[i]->enetaddr[0] << 24) | (dev[i]->enetaddr[1] << 16) | (dev[i]->enetaddr[2] << 8) | (dev[i]->enetaddr[3] << 0);

		ag7240_reg_wr(ag7240_macs[i], AG7240_GE_MAC_ADDR1, mac_l);
		ag7240_reg_wr(ag7240_macs[i], AG7240_GE_MAC_ADDR2, mac_h);

		/* if using header for register configuration, we have to     */
		/* configure s26 register after frame transmission is enabled */

		if (ag7240_macs[i]->mac_unit == 0) { /* WAN Phy */
#ifdef CONFIG_AR7242_S16_PHY
			if (is_ar7242() || is_wasp()) {
				athrs16_reg_init();
			} else
#endif
			{
#ifdef CFG_ATHRS26_PHY
	#ifdef AG7240_DEBUG
				printf("s26 reg init \n");
	#endif
				athrs26_reg_init();
#endif
#ifdef CFG_ATHRS27_PHY
	#ifdef AG7240_DEBUG
				printf("s27 reg init \n");
	#endif
				athrs27_reg_init();
#endif
#ifdef CONFIG_F1E_PHY
	#ifdef AG7240_DEBUG
				printf("F1Phy reg init \n");
	#endif
				athr_reg_init();
#endif
			}
		} else {
#ifdef CFG_ATHRS26_PHY
	#ifdef AG7240_DEBUG
			printf("athrs26_reg_init_lan\n");
	#endif
			athrs26_reg_init_lan();
#endif
#ifdef CFG_ATHRS27_PHY
	#ifdef AG7240_DEBUG
			printf("s27 reg init lan \n");
	#endif
			athrs27_reg_init_lan();
#endif
		}

#ifdef AG7240_DEBUG
		printf("ag7240_phy_setup\n");
#endif
		//udelay(100*1000);

		ag7240_phy_setup(ag7240_macs[i]->mac_unit);

#ifdef AG7240_DEBUG
		printf("Interface %s is up\n", dev[i]->name);
#endif
	}

	return 1;
}
Exemplo n.º 2
0
Arquivo: ag934x.c Projeto: jhbsz/102
static void ag7240_get_ethaddr(struct eth_device *dev)
{
    unsigned char *eeprom;
    unsigned char *mac = dev->enetaddr;
#ifndef CONFIG_AR7240_EMU

#ifdef CONFIG_ATH_NAND_BR
    unsigned char sectorBuff[ATH_ETH_MAC_READ_SIZE];

    eeprom = ath_eth_mac_addr(sectorBuff);
    if(eeprom == NULL) {
        /* mac address will be set to default mac address */
        mac[0] = 0xff;
    }
    else {
#else  /* CONFIG_ATH_NAND_BR */
    eeprom = ag7240_mac_addr_loc();
#endif  /* CONFIG_ATH_NAND_BR */

        if (strcmp(dev->name, "eth0") == 0) {
            memcpy(mac, eeprom, 6);
        } else if (strcmp(dev->name, "eth1") == 0) {
            eeprom += 6;
            memcpy(mac, eeprom, 6);
        } else {
            printf("%s: unknown ethernet device %s\n", __func__, dev->name);
            return;
        }
#ifdef CONFIG_ATH_NAND_BR
    }
#endif  /* CONFIG_ATH_NAND_BR */
    /* Use fixed address if the above address is invalid */
    if (mac[0] != 0x00 || (mac[0] == 0xff && mac[5] == 0xff)) {
#else
    if (1) {
#endif
        mac[0] = 0x00;
        mac[1] = 0x03;
        mac[2] = 0x7f;
        mac[3] = 0x09;
        mac[4] = 0x0b;
        mac[5] = 0xad;
        printf("No valid address in Flash. Using fixed address\n");
    } else {
        printf("Fetching MAC Address from 0x%p\n", __func__, eeprom);
    }
}


int ag7240_enet_initialize(bd_t * bis)
{
    struct eth_device *dev[CFG_AG7240_NMACS];
    u32 mask, mac_h, mac_l;
    int i;

    printf("ag934x_enet_initialize...\n");

    if(is_ar933x() && (ar7240_reg_rd(AR7240_RESET)!=0))
        ar7240_reg_wr(AR7240_RESET,0);

    if(is_ar933x())  //Turn on LED
        ar7240_reg_wr(AR7240_GPIO_BASE + 0x28 , ar7240_reg_rd(AR7240_GPIO_BASE + 0x28)  | (0xF8));

    for (i = 0; i < CFG_AG7240_NMACS; i++) {

        if ((dev[i] = (struct eth_device *) malloc(sizeof (struct eth_device))) == NULL) {
            puts("malloc failed\n");
            return 0;
        }

        if ((ag7240_macs[i] = (ag7240_mac_t *) malloc(sizeof (ag7240_mac_t))) == NULL) {
            puts("malloc failed\n");
            return 0;
        }

        memset(ag7240_macs[i], 0, sizeof(ag7240_macs[i]));
        memset(dev[i], 0, sizeof(dev[i]));

        sprintf(dev[i]->name, "eth%d", i);
        ag7240_get_ethaddr(dev[i]);

        ag7240_macs[i]->mac_unit = i;
        ag7240_macs[i]->mac_base = i ? AR7240_GE1_BASE : AR7240_GE0_BASE ;
        ag7240_macs[i]->dev = dev[i];

        dev[i]->iobase = 0;
        dev[i]->init = ag7240_clean_rx;
        dev[i]->halt = ag7240_halt;
        dev[i]->send = ag7240_send;
        dev[i]->recv = ag7240_recv;
        dev[i]->priv = (void *)ag7240_macs[i];
    }
#if !defined(CONFIG_ATH_NAND_BR)
    mask = AR7240_RESET_GE1_PHY;
    ar7240_reg_rmw_set(AR7240_RESET, mask);
    udelay(1000 * 100);
    ar7240_reg_rmw_clear(AR7240_RESET, mask);
    udelay(100);
#endif
    mask = AR7240_RESET_GE0_PHY;
    ar7240_reg_rmw_set(AR7240_RESET, mask);
    udelay(1000 * 100);
    ar7240_reg_rmw_clear(AR7240_RESET, mask);
    udelay(100);


    for (i = 0; i < CFG_AG7240_NMACS; i++) {
        eth_register(dev[i]);
#if(CONFIG_COMMANDS & CFG_CMD_MII)
        miiphy_register(dev[i]->name, ag7240_miiphy_read, ag7240_miiphy_write);
#endif

        ag7240_reg_rmw_set(ag7240_macs[i], AG7240_MAC_CFG1, AG7240_MAC_CFG1_SOFT_RST
                           | AG7240_MAC_CFG1_RX_RST | AG7240_MAC_CFG1_TX_RST);

        if(!i) {
            mask = (AR7240_RESET_GE0_MAC  | AR7240_RESET_GE1_MAC);

            if (is_ar7241() || is_ar7242() ||  is_wasp())
                mask = mask | AR7240_RESET_GE0_MDIO | AR7240_RESET_GE1_MDIO;

            printf(" wasp  reset mask:%x \n",mask);

            ar7240_reg_rmw_set(AR7240_RESET, mask);
            udelay(1000 * 100);

            ar7240_reg_rmw_clear(AR7240_RESET, mask);
            udelay(1000 * 100);

            udelay(10 * 1000);
        }

        ag7240_mii_setup(ag7240_macs[i]);

        /* if using header for register configuration, we have to     */
        /* configure s26 register after frame transmission is enabled */

        if (ag7240_macs[i]->mac_unit == 0) { /* WAN Phy */
#ifdef CONFIG_AR7242_S16_PHY
            if (is_ar7242() || is_wasp()) {
                athrs16_reg_init();
            } else
#endif
            {
#ifdef  CONFIG_ATHRS17_PHY
                athrs17_reg_init();
#endif

#ifdef CFG_ATHRS26_PHY
                athrs26_reg_init();
#endif
#ifdef CFG_ATHRS27_PHY
                printf("s27 reg init \n");
                athrs27_reg_init();
#endif
#ifdef CONFIG_F1E_PHY
                printf("F1Phy reg init \n");
                athr_reg_init();
#endif
#ifdef CONFIG_VIR_PHY
                printf("VIRPhy reg init \n");
                athr_vir_reg_init();
#endif
#ifdef CONFIG_F2E_PHY
                printf("F2Phy reg init \n");
                athr_reg_init();
#endif

            }
        } else {
#ifdef CFG_ATHRS26_PHY
            athrs26_reg_init_lan();
#endif
#ifdef CFG_ATHRS27_PHY
            printf("s27 reg init lan \n");
            athrs27_reg_init_lan();
#endif
        }
        ag7240_hw_start(ag7240_macs[i]);
        ag7240_setup_fifos(ag7240_macs[i]);

        udelay(100 * 1000);

        {
            unsigned char *mac = dev[i]->enetaddr;

            printf("%s: %02x:%02x:%02x:%02x:%02x:%02x\n", dev[i]->name,
                   mac[0] & 0xff, mac[1] & 0xff, mac[2] & 0xff,
                   mac[3] & 0xff, mac[4] & 0xff, mac[5] & 0xff);
        }
        mac_l = (dev[i]->enetaddr[4] << 8) | (dev[i]->enetaddr[5]);
        mac_h = (dev[i]->enetaddr[0] << 24) | (dev[i]->enetaddr[1] << 16) |
                (dev[i]->enetaddr[2] << 8) | (dev[i]->enetaddr[3] << 0);

        ag7240_reg_wr(ag7240_macs[i], AG7240_GE_MAC_ADDR1, mac_l);
        ag7240_reg_wr(ag7240_macs[i], AG7240_GE_MAC_ADDR2, mac_h);


        ag7240_phy_setup(ag7240_macs[i]->mac_unit);
        printf("%s up\n",dev[i]->name);
    }

    return 1;
}

#if (CONFIG_COMMANDS & CFG_CMD_MII)
int
ag7240_miiphy_read(char *devname, uint32_t phy_addr, uint8_t reg, uint16_t *data)
{
    ag7240_mac_t *mac   = ag7240_name2mac(devname);
    uint16_t      addr  = (phy_addr << AG7240_ADDR_SHIFT) | reg, val;
    volatile int           rddata;
    uint16_t      ii = 0xFFFF;


    /*
     * Check for previous transactions are complete. Added to avoid
     * race condition while running at higher frequencies.
     */
    do
    {
        udelay(5);
        rddata = ag7240_reg_rd(mac, AG7240_MII_MGMT_IND) & 0x1;
    } while(rddata && --ii);

    if (ii == 0)
        printf("ERROR:%s:%d transaction failed\n",__func__,__LINE__);


    ag7240_reg_wr(mac, AG7240_MII_MGMT_CMD, 0x0);
    ag7240_reg_wr(mac, AG7240_MII_MGMT_ADDRESS, addr);
    ag7240_reg_wr(mac, AG7240_MII_MGMT_CMD, AG7240_MGMT_CMD_READ);

    do
    {
        udelay(5);
        rddata = ag7240_reg_rd(mac, AG7240_MII_MGMT_IND) & 0x1;
    } while(rddata && --ii);

    if(ii==0)
        printf("Error!!! Leave ag7240_miiphy_read without polling correct status!\n");

    val = ag7240_reg_rd(mac, AG7240_MII_MGMT_STATUS);
    ag7240_reg_wr(mac, AG7240_MII_MGMT_CMD, 0x0);

    if(data != NULL)
        *data = val;

    return val;
}
Exemplo n.º 3
0
int ag7240_enet_initialize(bd_t * bis){
	struct eth_device *dev[CFG_AG7240_NMACS];
	u32 mask, mac_h, mac_l;
	int i;

	//printf("ag934x_enet_initialize...\n");

	/*
	if(is_ar933x() && (ar7240_reg_rd(AR7240_RESET)!=0)){
		ar7240_reg_wr(AR7240_RESET,0);
	}

	if(is_ar933x())  //Turn on LED
	ar7240_reg_wr(AR7240_GPIO_BASE + 0x28 , ar7240_reg_rd(AR7240_GPIO_BASE + 0x28)  | (0xF8));
	*/

	for(i = 0;i < CFG_AG7240_NMACS;i++){
		if((dev[i] = (struct eth_device *)malloc(sizeof(struct eth_device))) == NULL){
			//puts("malloc failed\n");
			return(0);
		}

		if((ag7240_macs[i] = (ag7240_mac_t *)malloc(sizeof(ag7240_mac_t))) == NULL){
			//puts("malloc failed\n");
			return(0);
		}

		memset(ag7240_macs[i], 0, sizeof(ag7240_macs[i]));
		memset(dev[i], 0, sizeof(dev[i]));

		sprintf(dev[i]->name, "eth%d", i);
		ag7240_get_ethaddr(dev[i]);

		ag7240_macs[i]->mac_unit = i;
		ag7240_macs[i]->mac_base = i ? AR7240_GE1_BASE : AR7240_GE0_BASE ;
		ag7240_macs[i]->dev = dev[i];

		dev[i]->iobase = 0;
		dev[i]->init = ag7240_clean_rx;
		dev[i]->halt = ag7240_halt;
		dev[i]->send = ag7240_send;
		dev[i]->recv = ag7240_recv;
		dev[i]->priv = (void *)ag7240_macs[i];
	}
	
	for(i = 0;i < CFG_AG7240_NMACS;i++){
		eth_register(dev[i]);
	
#if(CONFIG_COMMANDS & CFG_CMD_MII)
		miiphy_register(dev[i]->name, ag7240_miiphy_read, ag7240_miiphy_write);
#endif

		ag7240_reg_rmw_set(ag7240_macs[i], AG7240_MAC_CFG1, AG7240_MAC_CFG1_SOFT_RST | AG7240_MAC_CFG1_RX_RST | AG7240_MAC_CFG1_TX_RST);

		if(!i){
			mask = (AR7240_RESET_GE0_MAC | AR7240_RESET_GE0_PHY | AR7240_RESET_GE1_MAC | AR7240_RESET_GE1_PHY);

			if(is_ar7241() || is_ar7242() ||  is_wasp()){
				mask = mask | AR7240_RESET_GE0_MDIO | AR7240_RESET_GE1_MDIO;
			}

			//printf(" wasp  reset mask:%x \n",mask);

			ar7240_reg_rmw_set(AR7240_RESET, mask);
			udelay(1000 * 100);

			ar7240_reg_rmw_clear(AR7240_RESET, mask);
			udelay(1000 * 100);

			udelay(10 * 1000);
		}

		ag7240_hw_start(ag7240_macs[i]);
		ag7240_setup_fifos(ag7240_macs[i]);

		udelay(100 * 1000);

		//unsigned char *mac = dev[i]->enetaddr;
		//printf("%s: %02x:%02x:%02x:%02x:%02x:%02x\n", dev[i]->name, mac[0] & 0xff, mac[1] & 0xff, mac[2] & 0xff, mac[3] & 0xff, mac[4] & 0xff, mac[5] & 0xff);

		mac_l = (dev[i]->enetaddr[4] << 8) | (dev[i]->enetaddr[5]);
		mac_h = (dev[i]->enetaddr[0] << 24) | (dev[i]->enetaddr[1] << 16) | (dev[i]->enetaddr[2] << 8) | (dev[i]->enetaddr[3] << 0);

		ag7240_reg_wr(ag7240_macs[i], AG7240_GE_MAC_ADDR1, mac_l);
		ag7240_reg_wr(ag7240_macs[i], AG7240_GE_MAC_ADDR2, mac_h);

		/* if using header for register configuration, we have to     */
		/* configure s26 register after frame transmission is enabled */
		if(ag7240_macs[i]->mac_unit == 0){ /* WAN Phy */
#ifdef CONFIG_AR7242_S16_PHY
			if(is_ar7242() || is_wasp()){
				athrs16_reg_init();
			} else
#endif
			{
#ifdef  CFG_ATHRS17_PHY
			athrs17_reg_init();
#endif

#ifdef CFG_ATHRS26_PHY
			athrs26_reg_init();
#endif

#ifdef CFG_ATHRS27_PHY
			//printf("s27 reg init \n");
			athrs27_reg_init();
#endif

#ifdef CONFIG_F1E_PHY
			//printf("F1Phy reg init \n");
			athr_reg_init();
#endif

#ifdef CONFIG_VIR_PHY
			//printf("VIRPhy reg init \n");
			athr_vir_reg_init();
#endif

#ifdef CONFIG_F2E_PHY
			//printf("F2Phy reg init \n");
			athr_reg_init();
#endif

			}
		} else {
#ifdef CFG_ATHRS26_PHY
			athrs26_reg_init_lan();
#endif

#ifdef CFG_ATHRS27_PHY
			//printf("s27 reg init lan \n");
			athrs27_reg_init_lan();
#endif
		}

		ag7240_phy_setup(ag7240_macs[i]->mac_unit);
		//printf("%s up\n",dev[i]->name);
	}

	return(1);
}