/* this happens after cpu_init where exynos resources are set */
static void mainboard_init(device_t dev)
{
/* we'll stick with the crummy u-boot struct for now.*/
/* doing this as an auto since the struct has to be writeable */
struct edp_device_info device_info;
void *fb_addr = (void *)(get_fb_base_kb() * KiB);
gpio_init();
tmu_init(&exynos5420_tmu_info);
/* Clock Gating all the unused IP's to save power */
clock_gate();
/* Disable USB3.0 PLL to save 250mW of power */
disable_usb30_pll();
set_vbe_mode_info_valid(&edid, (uintptr_t)fb_addr);
/*
* The reset value for FIMD SYSMMU register MMU_CTRL:0x14640000
* should be 0 according to the datasheet, but has experimentally
* been found to come up as 3. This means FIMD SYSMMU is on by
* default on Exynos5420. For now we are disabling FIMD SYSMMU.
*/
writel(0x0, (void *)0x14640000);
writel(0x0, (void *)0x14680000);
lcd_vdd();
/* Start the fimd running before you do the phy and lcd setup.
* why do fimd before training etc?
* because we need a data stream from
* the fimd or the clock recovery step fails.
*/
vidinfo.screen_base = fb_addr;
exynos_fimd_lcd_init(&vidinfo);
parade_dp_bridge_setup();
/* this might get more dynamic in future ... */
memset(&device_info, 0, sizeof(device_info));
device_info.disp_info.name = (char *)"Pit display";
device_info.disp_info.h_total = 1366;
device_info.disp_info.v_total = 768;
device_info.video_info = dp_video_info;
device_info.raw_edid = panel_edid;
exynos_init_dp(&device_info);
udelay(LCD_T3_DELAY_MS * 1000);
backlight_vdd();
backlight_pwm();
backlight_en();
}
/* this happens after cpu_init where exynos resources are set */
static void mainboard_init(device_t dev)
{
int dp_tries;
struct s5p_dp_device dp_device = {
.base = exynos_dp1,
.video_info = &dp_video_info,
};
void *fb_addr = (void *)(get_fb_base_kb() * KiB);
prepare_usb();
gpio_init();
setup_storage();
i2c_init(TPS65090_BUS, I2C_0_SPEED, I2C_SLAVE);
i2c_init(7, I2C_0_SPEED, I2C_SLAVE);
tmu_init(&exynos5250_tmu_info);
/* Clock Gating all the unused IP's to save power */
clock_gate();
/* Disable USB3.0 PLL to save 250mW of power */
disable_usb30_pll();
sdmmc_vdd();
set_vbe_mode_info_valid(&edid, (uintptr_t)fb_addr);
lcd_vdd();
// FIXME: should timeout
do {
udelay(50);
} while (!exynos_dp_hotplug());
exynos_dp_bridge_setup();
for (dp_tries = 1; dp_tries <= MAX_DP_TRIES; dp_tries++) {
exynos_dp_bridge_init();
if (exynos_dp_hotplug()) {
exynos_dp_reset();
continue;
}
if (dp_controller_init(&dp_device))
continue;
udelay(LCD_T3_DELAY_MS * 1000);
backlight_vdd();
backlight_pwm();
backlight_en();
/* if we're here, we're successful */
break;
}
if (dp_tries > MAX_DP_TRIES)
printk(BIOS_ERR, "%s: Failed to set up displayport\n", __func__);
setup_usb();
// Uncomment to get excessive GPIO output:
// gpio_info();
}
/* this happens after cpu_init where exynos resources are set */
static void mainboard_init(device_t dev)
{
int dp_tries;
struct s5p_dp_device dp_device = {
.base = (struct exynos5_dp *)EXYNOS5250_DP1_BASE,
.video_info = &dp_video_info,
};
void *fb_addr = (void *)(get_fb_base_kb() * KiB);
gpio_init();
i2c_init(TPS65090_BUS, I2C_0_SPEED, I2C_SLAVE);
i2c_init(7, I2C_0_SPEED, I2C_SLAVE);
tmu_init(&exynos5250_tmu_info);
/* Clock Gating all the unused IP's to save power */
clock_gate();
/* Disable USB3.0 PLL to save 250mW of power */
disable_usb30_pll();
set_vbe_mode_info_valid(&edid, (uintptr_t)fb_addr);
lcd_vdd();
// FIXME: should timeout
do {
udelay(50);
} while (!exynos_dp_hotplug());
exynos_dp_bridge_setup();
for (dp_tries = 1; dp_tries <= MAX_DP_TRIES; dp_tries++) {
exynos_dp_bridge_init();
if (exynos_dp_hotplug()) {
exynos_dp_reset();
continue;
}
if (dp_controller_init(&dp_device))
continue;
udelay(LCD_T3_DELAY_MS * 1000);
backlight_vdd();
backlight_pwm();
backlight_en();
/* if we're here, we're successful */
break;
}
if (dp_tries > MAX_DP_TRIES)
printk(BIOS_ERR, "%s: Failed to set up displayport\n", __func__);
// Uncomment to get excessive GPIO output:
// gpio_info();
}
static void mainboard_enable(device_t dev)
{
dev->ops->init = &mainboard_init;
/* set up dcache and MMU */
/* FIXME: this should happen via resource allocator */
exynos5250_config_l2_cache();
mmu_init();
mmu_config_range(0, DRAM_START, DCACHE_OFF);
mmu_config_range(DRAM_START, DRAM_SIZE, DCACHE_WRITEBACK);
mmu_config_range(DRAM_END, 4096 - DRAM_END, DCACHE_OFF);
dcache_invalidate_all();
dcache_mmu_enable();
/* this is going to move, but we must have it now and we're
* not sure where */
exception_init();
const unsigned epll_hz = 192000000;
const unsigned sample_rate = 48000;
const unsigned lr_frame_size = 256;
clock_epll_set_rate(epll_hz);
clock_select_i2s_clk_source();
clock_set_i2s_clk_prescaler(epll_hz, sample_rate * lr_frame_size);
power_enable_xclkout();
}
