int ISR(SERIAL_RX)
{
uint8_t data = UDR0;
uint8_t next_head;
// Pick off runtime command characters directly from the serial stream. These characters are
// not passed into the buffer, but these set system state flag bits for runtime execution.
switch (data) {
case CMD_STATUS_REPORT: bit_true_atomic(sys.execute, EXEC_STATUS_REPORT); break; // Set as true
case CMD_CYCLE_START: bit_true_atomic(sys.execute, EXEC_CYCLE_START); break; // Set as true
case CMD_FEED_HOLD: bit_true_atomic(sys.execute, EXEC_FEED_HOLD); break; // Set as true
case CMD_RESET: mc_reset(); break; // Call motion control reset routine.
default: // Write character to buffer
next_head = serial_rx_buffer_head + 1;
if (next_head == RX_BUFFER_SIZE) { next_head = 0; }
// Write data to buffer unless it is full.
if (next_head != serial_rx_buffer_tail) {
serial_rx_buffer[serial_rx_buffer_head] = data;
serial_rx_buffer_head = next_head;
#ifdef ENABLE_XONXOFF
if ((serial_get_rx_buffer_count() >= RX_BUFFER_FULL) && flow_ctrl == XON_SENT) {
flow_ctrl = SEND_XOFF;
UCSR0B |= (1 << UDRIE0); // Force TX
}
#endif
}
//TODO: else alarm on overflow?
}
}
void serial_rxint(void)
{
uint8_t data = usart_recv(USART2);;
uint32_t next_head;
// Pick off realtime command characters directly from the serial stream. These characters are
// not passed into the buffer, but these set system state flag bits for realtime execution.
switch (data) {
case CMD_STATUS_REPORT: bit_true_atomic(sys.rt_exec_state, EXEC_STATUS_REPORT); break; // Set as true
case CMD_CYCLE_START: bit_true_atomic(sys.rt_exec_state, EXEC_CYCLE_START); break; // Set as true
case CMD_FEED_HOLD: bit_true_atomic(sys.rt_exec_state, EXEC_FEED_HOLD); break; // Set as true
case CMD_SAFETY_DOOR: bit_true_atomic(sys.rt_exec_state, EXEC_SAFETY_DOOR); break; // Set as true
case CMD_RESET: mc_reset(); break; // Call motion control reset routine.
default: // Write character to buffer
next_head = serial_rx_buffer_head + 1;
if (next_head == RX_BUFFER_SIZE) { next_head = 0; }
// Write data to buffer unless it is full.
if (next_head != serial_rx_buffer_tail) {
serial_rx_buffer[serial_rx_buffer_head] = data;
serial_rx_buffer_head = next_head;
#ifdef ENABLE_XONXOFF
if ((serial_get_rx_buffer_count() >= RX_BUFFER_FULL) && flow_ctrl == XON_SENT) {
flow_ctrl = SEND_XOFF;
usart_enable_tx_interrupt(USART2);
}
#endif
}
//TODO: else alarm on overflow?
}
}
// Method to ready the system to reset by setting the runtime reset command and killing any
// active processes in the system. This also checks if a system reset is issued while Grbl
// is in a motion state. If so, kills the steppers and sets the system alarm to flag position
// lost, since there was an abrupt uncontrolled deceleration. Called at an interrupt level by
// runtime abort command and hard limits. So, keep to a minimum.
void mc_reset()
{
// Only this function can set the system reset. Helps prevent multiple kill calls.
if (bit_isfalse(sys.execute, EXEC_RESET)) {
bit_true_atomic(sys.execute, EXEC_RESET);
/*// Kill spindle and coolant.
spindle_stop();
coolant_stop();*/
// Kill steppers only if in any motion state, i.e. cycle, feed hold, homing, or jogging
// NOTE: If steppers are kept enabled via the step idle delay setting, this also keeps
// the steppers enabled by avoiding the go_idle call altogether, unless the motion state is
// violated, by which, all bets are off.
if (sys.state & (STATE_CYCLE | STATE_HOLD | STATE_HOMING)) {
bit_true_atomic(sys.execute, EXEC_ALARM); // Flag main program to execute alarm state.
st_go_idle(); // Force kill steppers. Position has likely been lost.
}
}
}
// Method to ready the system to reset by setting the realtime reset command and killing any
// active processes in the system. This also checks if a system reset is issued while Grbl
// is in a motion state. If so, kills the steppers and sets the system alarm to flag position
// lost, since there was an abrupt uncontrolled deceleration. Called at an interrupt level by
// realtime abort command and hard limits. So, keep to a minimum.
void mc_reset()
{
// Only this function can set the system reset. Helps prevent multiple kill calls.
if (bit_isfalse(sys_rt_exec_state, EXEC_RESET)) {
bit_true_atomic(sys_rt_exec_state, EXEC_RESET);
// Kill spindle and coolant.
spindle_stop();
coolant_stop();
// Kill steppers only if in any motion state, i.e. cycle, actively holding, or homing.
// NOTE: If steppers are kept enabled via the step idle delay setting, this also keeps
// the steppers enabled by avoiding the go_idle call altogether, unless the motion state is
// violated, by which, all bets are off.
if ((sys.state & (STATE_CYCLE | STATE_HOMING)) || (sys.suspend == SUSPEND_ENABLE_HOLD)) {
if (sys.state == STATE_HOMING) { bit_true_atomic(sys_rt_exec_alarm, EXEC_ALARM_HOMING_FAIL); }
else { bit_true_atomic(sys_rt_exec_alarm, EXEC_ALARM_ABORT_CYCLE); }
st_go_idle(); // Force kill steppers. Position has likely been lost.
}
}
}
// Performs a soft limit check. Called from mc_line() only. Assumes the machine has been homed,
// the workspace volume is in all negative space, and the system is in normal operation.
void limits_soft_check(float *target)
{
uint8_t idx;
uint8_t soft_limit_error = false;
for (idx=0; idx<N_AXIS; idx++) {
#ifdef HOMING_FORCE_SET_ORIGIN
// When homing forced set origin is enabled, soft limits checks need to account for directionality.
// NOTE: max_travel is stored as negative
if (bit_istrue(settings.homing_dir_mask,bit(idx))) {
if (target[idx] < 0 || target[idx] > -settings.max_travel[idx]) { soft_limit_error = true; }
} else {
if (target[idx] > 0 || target[idx] < settings.max_travel[idx]) { soft_limit_error = true; }
}
#else
// NOTE: max_travel is stored as negative
if (target[idx] > 0 || target[idx] < settings.max_travel[idx]) { soft_limit_error = true; }
#endif
if (soft_limit_error) {
// Force feed hold if cycle is active. All buffered blocks are guaranteed to be within
// workspace volume so just come to a controlled stop so position is not lost. When complete
// enter alarm mode.
if (sys.state == STATE_CYCLE) {
bit_true_atomic(sys.execute, EXEC_FEED_HOLD);
do {
protocol_execute_runtime();
if (sys.abort) { return; }
} while ( sys.state != STATE_IDLE || sys.state != STATE_QUEUED);
}
mc_reset(); // Issue system reset and ensure spindle and coolant are shutdown.
bit_true_atomic(sys.execute, (EXEC_ALARM | EXEC_CRIT_EVENT)); // Indicate soft limit critical event
protocol_execute_runtime(); // Execute to enter critical event loop and system abort
return;
}
}
}
// Perform homing cycle to locate and set machine zero. Only '$H' executes this command.
// NOTE: There should be no motions in the buffer and Grbl must be in an idle state before
// executing the homing cycle. This prevents incorrect buffered plans after homing.
void mc_homing_cycle()
{
// Check and abort homing cycle, if hard limits are already enabled. Helps prevent problems
// with machines with limits wired on both ends of travel to one limit pin.
// TODO: Move the pin-specific LIMIT_PIN call to limits.c as a function.
#ifdef LIMITS_TWO_SWITCHES_ON_AXES
if (limits_get_state()) {
mc_reset(); // Issue system reset and ensure spindle and coolant are shutdown.
bit_true_atomic(sys_rt_exec_alarm, (EXEC_ALARM_HARD_LIMIT|EXEC_CRITICAL_EVENT));
return;
}
#endif
limits_disable(); // Disable hard limits pin change register for cycle duration
// -------------------------------------------------------------------------------------
// Perform homing routine. NOTE: Special motion case. Only system reset works.
// Search to engage all axes limit switches at faster homing seek rate.
limits_go_home(HOMING_CYCLE_0); // Homing cycle 0
#ifdef HOMING_CYCLE_1
limits_go_home(HOMING_CYCLE_1); // Homing cycle 1
#endif
#ifdef HOMING_CYCLE_2
limits_go_home(HOMING_CYCLE_2); // Homing cycle 2
#endif
#ifdef HOMING_CYCLE_3
limits_go_home(HOMING_CYCLE_3); // Homing cycle 3
#endif
#ifdef HOMING_CYCLE_4
limits_go_home(HOMING_CYCLE_4); // Homing cycle 4
#endif
#ifdef HOMING_CYCLE_5
limits_go_home(HOMING_CYCLE_5); // Homing cycle 5
#endif
protocol_execute_realtime(); // Check for reset and set system abort.
if (sys.abort) { return; } // Did not complete. Alarm state set by mc_alarm.
// Homing cycle complete! Setup system for normal operation.
// -------------------------------------------------------------------------------------
// Gcode parser position was circumvented by the limits_go_home() routine, so sync position now.
gc_sync_position();
// If hard limits feature enabled, re-enable hard limits pin change register after homing cycle.
limits_init();
}
void mc_probe_cycle(float *target, float feed_rate, uint8_t invert_feed_rate, uint8_t is_probe_away,
uint8_t is_no_error)
#endif
{
// TODO: Need to update this cycle so it obeys a non-auto cycle start.
if (sys.state == STATE_CHECK_MODE) { return; }
// Finish all queued commands and empty planner buffer before starting probe cycle.
protocol_buffer_synchronize();
// Initialize probing control variables
sys.probe_succeeded = false; // Re-initialize probe history before beginning cycle.
probe_configure_invert_mask(is_probe_away);
// After syncing, check if probe is already triggered. If so, halt and issue alarm.
// NOTE: This probe initialization error applies to all probing cycles.
if ( probe_get_state() ) { // Check probe pin state.
bit_true_atomic(sys_rt_exec_alarm, EXEC_ALARM_PROBE_FAIL);
protocol_execute_realtime();
}
if (sys.abort) { return; } // Return if system reset has been issued.
// Setup and queue probing motion. Auto cycle-start should not start the cycle.
#ifdef USE_LINE_NUMBERS
mc_line(target, feed_rate, invert_feed_rate, line_number);
#else
mc_line(target, feed_rate, invert_feed_rate);
#endif
// Activate the probing state monitor in the stepper module.
sys_probe_state = PROBE_ACTIVE;
// Perform probing cycle. Wait here until probe is triggered or motion completes.
bit_true_atomic(sys_rt_exec_state, EXEC_CYCLE_START);
do {
protocol_execute_realtime();
if (sys.abort) { return; } // Check for system abort
} while (sys.state != STATE_IDLE);
// Probing cycle complete!
// Set state variables and error out, if the probe failed and cycle with error is enabled.
if (sys_probe_state == PROBE_ACTIVE) {
if (is_no_error) { memcpy(sys.probe_position, sys.position, sizeof(float)*N_AXIS); }
else { bit_true_atomic(sys_rt_exec_alarm, EXEC_ALARM_PROBE_FAIL); }
} else {
sys.probe_succeeded = true; // Indicate to system the probing cycle completed successfully.
}
sys_probe_state = PROBE_OFF; // Ensure probe state monitor is disabled.
protocol_execute_realtime(); // Check and execute run-time commands
if (sys.abort) { return; } // Check for system abort
// Reset the stepper and planner buffers to remove the remainder of the probe motion.
st_reset(); // Reest step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure probing motion is cleared.
plan_sync_position(); // Sync planner position to current machine position.
// TODO: Update the g-code parser code to not require this target calculation but uses a gc_sync_position() call.
// NOTE: The target[] variable updated here will be sent back and synced with the g-code parser.
system_convert_array_steps_to_mpos(target, sys.position);
#ifdef MESSAGE_PROBE_COORDINATES
// All done! Output the probe position as message.
report_probe_parameters();
#endif
}
// Homes the specified cycle axes, sets the machine position, and performs a pull-off motion after
// completing. Homing is a special motion case, which involves rapid uncontrolled stops to locate
// the trigger point of the limit switches. The rapid stops are handled by a system level axis lock
// mask, which prevents the stepper algorithm from executing step pulses. Homing motions typically
// circumvent the processes for executing motions in normal operation.
// NOTE: Only the abort runtime command can interrupt this process.
void limits_go_home(uint8_t cycle_mask)
{
if (sys.abort) { return; } // Block if system reset has been issued.
// Initialize homing in search mode to quickly engage the specified cycle_mask limit switches.
bool approach = true;
float homing_rate = settings.homing_seek_rate;
uint8_t invert_pin, idx;
uint8_t n_cycle = (2*N_HOMING_LOCATE_CYCLE+1); ///***5
float target[N_AXIS];
uint8_t limit_pin[N_AXIS], step_pin[N_AXIS];
float max_travel = 0.0;
for (idx=0; idx<N_AXIS; idx++) {
// Initialize limit and step pin masks
limit_pin[idx] = get_limit_pin_mask(idx); ///////****get the Pin of limit min x, y ,z , Limit OK
step_pin[idx] = get_step_pin_mask(idx); ///////****get the Pin of limit min x, y ,z now I let it 0, 1, 2
// Determine travel distance to the furthest homing switch based on user max travel settings.
// NOTE: settings.max_travel[] is stored as a negative value.
if (max_travel > settings.max_travel[idx]) { max_travel = settings.max_travel[idx]; }
}
max_travel *= -HOMING_AXIS_SEARCH_SCALAR; // Ensure homing switches engaged by over-estimating max travel.
plan_reset(); // Reset planner buffer to zero planner current position and to clear previous motions.
do {
// Initialize invert_pin boolean based on approach and invert pin user setting.
if (bit_isfalse(settings.flags,BITFLAG_INVERT_LIMIT_PINS)) { invert_pin = approach; }
else { invert_pin = !approach; }
// Initialize and declare variables needed for homing routine.
uint8_t n_active_axis = 0;
uint8_t axislock = 0;
for (idx=0; idx<N_AXIS; idx++) {
// Set target location for active axes and setup computation for homing rate.
if (bit_istrue(cycle_mask,bit(idx))) {
n_active_axis++;
if (!approach) { target[idx] = -max_travel; }
else { target[idx] = max_travel; }
} else {
target[idx] = 0.0;
}
// Set target direction based on cycle mask
if (bit_istrue(settings.homing_dir_mask,bit(idx))) { target[idx] = -target[idx]; }
// Apply axislock to the step port pins active in this cycle.
if (bit_istrue(cycle_mask,bit(idx))) { axislock |= step_pin[idx]; }
}
homing_rate *= sqrt(n_active_axis); // [sqrt(N_AXIS)] Adjust so individual axes all move at homing rate.
sys.homing_axis_lock = axislock;
// Perform homing cycle. Planner buffer should be empty, as required to initiate the homing cycle.
uint8_t limit_state;
#ifdef USE_LINE_NUMBERS
plan_buffer_line(target, homing_rate, false, HOMING_CYCLE_LINE_NUMBER); // Bypass mc_line(). Directly plan homing motion.
#else
plan_buffer_line(target, homing_rate, false); // Bypass mc_line(). Directly plan homing motion.
#endif
st_prep_buffer(); // Prep and fill segment buffer from newly planned block.
st_wake_up(); // Initiate motion
do {
// Check limit state. Lock out cycle axes when they change.
/////////////////########################################***********
#if MotherBoard==3 /////**MB==3
#ifdef limit_int_style
limit_state = LIMIT_PIN;
if (invert_pin) { limit_state ^= LIMIT_MASK; }
#else
//************Get Limit Pin State. PiBot get limit/endstop mask same with the step mask.
#if LIMIT_MAX_OPEN
if(isXMinEndstopHit()) { limit_state^= MASK(X_LIMIT_BIT);} ////***read X_endstop then write into limite_state
if(isYMinEndstopHit()) { limit_state^= MASK(Y_LIMIT_BIT);}
if(isZMinEndstopHit()) { limit_state^= MASK(Z_LIMIT_BIT);} ////*****add MAX limit
if(isXMaxEndstopHit()) { limit_state^= MASK(X_LIMIT_MAX_BIT);} ////***read X_endstop then write into limite_state
if(isYMaxEndstopHit()) { limit_state^= MASK(Y_LIMIT_MAX_BIT);}
if(isZMaxEndstopHit()) { limit_state^= MASK(Z_LIMIT_MAX_BIT);} ////*****add MAX limit
#else
if(isXMinEndstopHit()) { limit_state^= MASK(X_MASK);} ////***read X_endstop then write into limite_state
if(isYMinEndstopHit()) { limit_state^= MASK(Y_MASK);}
if(isZMinEndstopHit()) { limit_state^= MASK(Z_MASK);} ////*****add MAX limit
#endif
#endif
#else /////**MB!=3 ////////#################################################
limit_state = LIMIT_PIN;
if (invert_pin) { limit_state ^= LIMIT_MASK; }
#endif /////**MB==3
/////////////////////////////#####################################
for (idx=0; idx<N_AXIS; idx++) {
if (axislock & step_pin[idx]) {
if (limit_state & limit_pin[idx]) { axislock &= ~(step_pin[idx]); }
}
}
sys.homing_axis_lock = axislock;
st_prep_buffer(); // Check and prep segment buffer. NOTE: Should take no longer than 200us.
// Check only for user reset. No time to run protocol_execute_runtime() in this loop.
if (sys.execute & EXEC_RESET) { protocol_execute_runtime(); return; }
} while (STEP_MASK & axislock);
st_reset(); // Immediately force kill steppers and reset step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure homing motion is cleared.
delay_ms(settings.homing_debounce_delay); // Delay to allow transient dynamics to dissipate.
// Reverse direction and reset homing rate for locate cycle(s).
homing_rate = settings.homing_feed_rate;
approach = !approach;
} while (n_cycle-- > 0);
// The active cycle axes should now be homed and machine limits have been located. By
// default, grbl defines machine space as all negative, as do most CNCs. Since limit switches
// can be on either side of an axes, check and set axes machine zero appropriately. Also,
// set up pull-off maneuver from axes limit switches that have been homed. This provides
// some initial clearance off the switches and should also help prevent them from falsely
// triggering when hard limits are enabled or when more than one axes shares a limit pin.
for (idx=0; idx<N_AXIS; idx++) {
// Set up pull off targets and machine positions for limit switches homed in the negative
// direction, rather than the traditional positive. Leave non-homed positions as zero and
// do not move them.
// NOTE: settings.max_travel[] is stored as a negative value.
if (cycle_mask & bit(idx)) {
#ifdef HOMING_FORCE_SET_ORIGIN
sys.position[idx] = 0; // Set axis homed location as axis origin
target[idx] = settings.homing_pulloff;
if ( bit_isfalse(settings.homing_dir_mask,bit(idx)) ) { target[idx] = -target[idx]; }
#else
if ( bit_istrue(settings.homing_dir_mask,bit(idx)) ) {
target[idx] = settings.homing_pulloff+settings.max_travel[idx];
sys.position[idx] = lround(settings.max_travel[idx]*settings.steps_per_mm[idx]);
} else {
target[idx] = -settings.homing_pulloff;
sys.position[idx] = 0;
}
#endif
} else { // Non-active cycle axis. Set target to not move during pull-off.
target[idx] = (float)sys.position[idx]/settings.steps_per_mm[idx];
}
}
plan_sync_position(); // Sync planner position to current machine position for pull-off move.
#ifdef USE_LINE_NUMBERS
plan_buffer_line(target, settings.homing_seek_rate, false, HOMING_CYCLE_LINE_NUMBER); // Bypass mc_line(). Directly plan motion.
#else
plan_buffer_line(target, settings.homing_seek_rate, false); // Bypass mc_line(). Directly plan motion.
#endif
// Initiate pull-off using main motion control routines.
// TODO : Clean up state routines so that this motion still shows homing state.
sys.state = STATE_QUEUED;
bit_true_atomic(sys.execute, EXEC_CYCLE_START);
protocol_execute_runtime();
protocol_buffer_synchronize(); // Complete pull-off motion.
// Set system state to homing before returning.
sys.state = STATE_HOMING;
}
void mc_probe_cycle(float *target, float feed_rate, uint8_t invert_feed_rate)
#endif
{
// TODO: Need to update this cycle so it obeys a non-auto cycle start.
if (sys.state == STATE_CHECK_MODE) { return; }
// Finish all queued commands and empty planner buffer before starting probe cycle.
protocol_buffer_synchronize();
uint8_t auto_start_state = sys.auto_start; // Store run state
// After syncing, check if probe is already triggered. If so, halt and issue alarm.
if (probe_get_state()) {
bit_true_atomic(sys.execute, EXEC_CRIT_EVENT);
protocol_execute_runtime();
}
if (sys.abort) { return; } // Return if system reset has been issued.
// Setup and queue probing motion. Auto cycle-start should not start the cycle.
#ifdef USE_LINE_NUMBERS
mc_line(target, feed_rate, invert_feed_rate, line_number);
#else
mc_line(target, feed_rate, invert_feed_rate);
#endif
// Activate the probing monitor in the stepper module.
sys.probe_state = PROBE_ACTIVE;
// Perform probing cycle. Wait here until probe is triggered or motion completes.
bit_true_atomic(sys.execute, EXEC_CYCLE_START);
do {
protocol_execute_runtime();
if (sys.abort) { return; } // Check for system abort
} while ((sys.state != STATE_IDLE) && (sys.state != STATE_QUEUED));
// Probing motion complete. If the probe has not been triggered, error out.
if (sys.probe_state == PROBE_ACTIVE) { bit_true_atomic(sys.execute, EXEC_CRIT_EVENT); }
protocol_execute_runtime(); // Check and execute run-time commands
if (sys.abort) { return; } // Check for system abort
// Reset the stepper and planner buffers to remove the remainder of the probe motion.
st_reset(); // Reest step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure probing motion is cleared.
plan_sync_position(); // Sync planner position to current machine position.
// Pull-off triggered probe to the trigger location since we had to decelerate a little beyond
// it to stop the machine in a controlled manner.
uint8_t idx;
for(idx=0; idx<N_AXIS; idx++){
// NOTE: The target[] variable updated here will be sent back and synced with the g-code parser.
target[idx] = (float)sys.probe_position[idx]/settings.steps_per_deg[idx];
}
#ifdef USE_LINE_NUMBERS
mc_line(target, feed_rate, invert_feed_rate, line_number);
#else
mc_line(target, feed_rate, invert_feed_rate);
#endif
// Execute pull-off motion and wait until it completes.
bit_true_atomic(sys.execute, EXEC_CYCLE_START);
protocol_buffer_synchronize();
if (sys.abort) { return; } // Return if system reset has been issued.
sys.auto_start = auto_start_state; // Restore run state before returning
#ifdef MESSAGE_PROBE_COORDINATES
// All done! Output the probe position as message.
report_probe_parameters();
#endif
}
// Auto-cycle start has two purposes: 1. Resumes a plan_synchronize() call from a function that
// requires the planner buffer to empty (spindle enable, dwell, etc.) 2. As a user setting that
// automatically begins the cycle when a user enters a valid motion command manually. This is
// intended as a beginners feature to help new users to understand g-code. It can be disabled
// as a beginner tool, but (1.) still operates. If disabled, the operation of cycle start is
// manually issuing a cycle start command whenever the user is ready and there is a valid motion
// command in the planner queue.
// NOTE: This function is called from the main loop, buffer sync, and mc_line() only and executes
// when one of these conditions exist respectively: There are no more blocks sent (i.e. streaming
// is finished, single commands), a command that needs to wait for the motions in the buffer to
// execute calls a buffer sync, or the planner buffer is full and ready to go.
void protocol_auto_cycle_start() { bit_true_atomic(sys_rt_exec_state, EXEC_CYCLE_START); }
// Auto-cycle start has two purposes: 1. Resumes a plan_synchronize() call from a function that
// requires the planner buffer to empty (spindle enable, dwell, etc.) 2. As a user setting that
// automatically begins the cycle when a user enters a valid motion command manually. This is
// intended as a beginners feature to help new users to understand g-code. It can be disabled
// as a beginner tool, but (1.) still operates. If disabled, the operation of cycle start is
// manually issuing a cycle start command whenever the user is ready and there is a valid motion
// command in the planner queue.
// NOTE: This function is called from the main loop and mc_line() only and executes when one of
// two conditions exist respectively: There are no more blocks sent (i.e. streaming is finished,
// single commands), or the planner buffer is full and ready to go.
void Grbl::Protocol::auto_cycle_start() { if (parent->m_system.sys.auto_start) { bit_true_atomic(parent->m_system.sys.execute, EXEC_CYCLE_START); } }