int bsp_i2c_debug(void)
{
int i = 0;
int count = 0;
unsigned int clk0 = 0;
unsigned int clk1 = 0;
bsp_i2c_initial();
#ifdef HI_I2C1_REGBASE_ADDR
clk0 = get_hi_crg_clkstat1_i2c0_clk_status();
clk1 = get_hi_crg_clkstat1_i2c1_clk_status();
cprintf("i2c0_clk:%d i2c1_clk:%d\n",clk0,clk1);
#endif
bsp_i2c_slave_register(I2C_MASTER1,TEST_SLAVE_ID);
/*µ¥×Ö½Ú²âÊÔ£¬05¼Ä´æÆ÷Á¬Ðø¶Áд50´Î*/
count=0;
for(i=0;i<50;i++){
if(I2C_TEST_PASS!=debug_i2c_byte_data_send(0x05,0x8a))
{
count++;
cprintf("register offset:0x05,send data:0x8a,times:%d\n\n",i);
}
}
cprintf("test count:%d times,success %d times\n\n",i,i-count);
/*µ¥×Ö½Ú²âÊÔ£¬02¼Ä´æÆ÷¶Áд50´Î*/
count = 0;
for(i=0;i<50;i++){
if(I2C_TEST_PASS!=debug_i2c_byte_data_send(0x2,0x8a))
{
count++;
cprintf("register offset:%x,send data:0x8a\n",i);
}
}
cprintf("\ntest count:%d times,success %d times\n\n",i,i-count);
/*Ë«×Ö½Ú²âÊÔ£¬05¼Ä´æÆ÷¶Áд50´Î*/
count=0;
for(i=0;i<50;i++){
if(I2C_TEST_PASS!=debug_i2c_word_data_send(0x02,0x8a8a))
{
count++;
cprintf("register offset:0x05,send data:0x8a,times:%d\n\n",i);
}
}
cprintf("\ntest count:%d times,success %d times\n\n",i,i-count);
/*Ë«×Ö½Ú²âÊÔ£¬02¼Ä´æÆ÷¶Áд50´Î*/
count = 0;
for(i=0;i<50;i++){
if(I2C_TEST_PASS!=debug_i2c_word_data_send(0x05,0x8a8a))
{
count++;
cprintf("register offset:0x02,send data:0x8a8a\n",i);
}
}
cprintf("\ntest count:%d times,success %d times\n\n",i,i-count);
return 0;
}
void BSP_DRV_Init()
{
#ifdef CONFIG_MODULE_VIC
s32 ret = 0;
#endif
/***********************基础模块初始化***************************/
#ifdef CONFIG_BALONG_CCLK
hi6930_clock_init();
#endif
#ifdef CONFIG_CCORE_PM
bsp_dpm_init();
#endif
#ifdef K3_TIMER_FEATURE
k3_timer_init();
#endif
adp_timer_init();
timer_dpm_init();
if(0 != BSP_UDI_Init())
logMsg("BSP_UDI_Init fail\n",0,0,0,0,0,0);
bsp_ipc_init();
bsp_icc_init();
#ifdef CONFIG_K3V3_CLK_CRG /*CONFIG_K3V3_CLK_CRG*/
gps_refclk_icc_read_cb_init();
#endif
/* Cshell init if magic number is set to PRT_FLAG_EN_MAGIC_M */
#ifdef CONFIG_CSHELL
if(0 != cshell_init())
{
logMsg("cshell init fail\n",0,0,0,0,0,0);
}
#endif
#ifdef CONFIG_NVIM
if(0 != bsp_nvm_init())
logMsg("nv init fail\n",0,0,0,0,0,0);
#endif
/* axi monitor监控初始化 */
(void)bsp_amon_init();
/*此初始化必须放置在MSP/OAM/PS初始化之前，请不要随意改动顺序*/
tcxo_init_configure();
if(0 != bsp_rfile_init())
logMsg("rfile init fail\n",0,0,0,0,0,0);
/* version inits */
bsp_productinfo_init();
hwspinlock_init();
bsp_hkadc_init();
bsp_version_init();
bsp_lowpower_mntn_init();
#ifdef CONFIG_MODULE_VIC
ret = bsp_vic_init();
if(ret != OK)
{
logMsg("bsp_vic_init error\n", 0, 0, 0, 0, 0, 0);
}
#endif
(void)bsp_softtimer_init();
#ifdef CONFIG_BALONG_EDMA
if(0 != bsp_edma_init())
{
logMsg("edma init fail \n",0,0,0,0,0,0);
}
#endif
/*C core init ipc module*/
if(0 != socp_init())
logMsg("socp init fail\n",0,0,0,0,0,0);
if(0 != bsp_om_server_init())
logMsg("om init fail\n",0,0,0,0,0,0);
if(0 != bsp_dual_modem_init())
logMsg("dual modem uart init fail\n",0,0,0,0,0,0);
/***********************外设模块初始化***************************/
bsp_dsp_init();
#ifdef CONFIG_BBP_INT
bbp_int_init();/*此处需要放在dsp初始化之后，放在pastar/abb之前*/
#endif
bsp_spi_init();
bsp_pmu_init();
regulator_init();
#if defined(CONFIG_PMIC_HI6559)
if(bsp_pa_rf_init()) /* 依赖于regulator_init */
{
logMsg("bsp_pa_rf_init fail\n",0,0,0,0,0,0);
}
#endif
/*init mipi*/
#ifdef CONFIG_MIPI
bsp_mipi_init();
#endif
#ifdef CONFIG_TUNER
bsp_tuner_init();
#endif
#ifdef CONFIG_PASTAR
/*此函数的位置不可以向后移动，为pastar上电后，提供足够的稳定时间*/
pmu_hi6561_init_phase1();
#endif
if(0 != hi6930_wdt_init())
logMsg("wdt init fail\n",0,0,0,0,0,0);
#ifdef CONFIG_CCORE_I2C
if(0!=bsp_i2c_initial())
logMsg("i2c init fail\n",0,0,0,0,0,0);
#endif
if(0 != bsp_gpio_init())
logMsg("gpio init fail\n",0,0,0,0,0,0);
#ifdef CONFIG_EFUSE
if(0 != efuse_init())
{
logMsg("efuse init fail \n",0,0,0,0,0,0);
}
#endif
#ifdef CONFIG_LEDS_CCORE
if(0 != bsp_led_init())
{
logMsg("led init fail\n",0,0,0,0,0,0);
}
#endif
/***********************通信支撑模块初始化***************************/
#ifdef CONFIG_CIPHER
if(0 != cipher_init())
{
logMsg("cipher init fail \n",0,0,0,0,0,0);
}
if(0 != bsp_acc_init())
{
logMsg("acc init fail \n",0,0,0,0,0,0);
}
#endif
#ifdef CONFIG_IPF
if(0 != ipf_init())
logMsg("ipf init fail\n",0,0,0,0,0,0);
#endif
#ifdef CONFIG_MODULE_BUSSTRESS
ipf_ul_stress_test_start(10);
#endif
#ifdef FEATURE_TLPHY_MAILBOX
bsp_mailbox_init();
#endif
mailbox_init();
#ifdef CONFIG_ANTEN
if(0 != bsp_anten_init())
logMsg("anten init fail.\n",0,0,0,0,0,0);
#endif
bsp_sci_cfg_init();
bsp_abb_init();
bsp_on_off_init();
cpufreq_init();
/*初始化醒来的时间戳*/
update_awake_time_stamp();
#ifdef CONFIG_CCORE_BALONG_PM
balong_pm_init();
#endif
#ifdef CONFIG_AUDIO
audio_init();
#endif
#ifdef CONFIG_BALONG_MODEM_RESET
bsp_reset_init();
#endif
(void)bsp_rf_rse_init();
#ifdef CONFIG_PASTAR
/*勿动!此处需要放置在该函数最后，确保pastar上电后稳定后，进行初始化配置*/
pmu_hi6561_init_phase2();
#endif
(void)bsp_antn_sw_init();
}
