static int davinci_musb_exit(struct musb *musb)
{
if (is_host_enabled(musb))
del_timer_sync(&otg_workaround);
if (cpu_is_davinci_dm355()) {
u32 deepsleep = __raw_readl(DM355_DEEPSLEEP);
deepsleep &= ~DRVVBUS_FORCE;
deepsleep |= DRVVBUS_OVERRIDE;
__raw_writel(deepsleep, DM355_DEEPSLEEP);
}
davinci_musb_source_power(musb, 0 , 1);
if (is_host_enabled(musb) && musb->xceiv->otg->default_a) {
int maxdelay = 30;
u8 devctl, warn = 0;
do {
devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
if (!(devctl & MUSB_DEVCTL_VBUS))
break;
if ((devctl & MUSB_DEVCTL_VBUS) != warn) {
warn = devctl & MUSB_DEVCTL_VBUS;
dev_dbg(musb->controller, "VBUS %d\n",
warn >> MUSB_DEVCTL_VBUS_SHIFT);
}
msleep(1000);
maxdelay--;
} while (maxdelay > 0);
static int davinci_musb_exit(struct musb *musb)
{
del_timer_sync(&otg_workaround);
/* force VBUS off */
if (cpu_is_davinci_dm355()) {
u32 deepsleep = __raw_readl(DM355_DEEPSLEEP);
deepsleep &= ~DRVVBUS_FORCE;
deepsleep |= DRVVBUS_OVERRIDE;
__raw_writel(deepsleep, DM355_DEEPSLEEP);
}
davinci_musb_source_power(musb, 0 /*off*/, 1);
/* delay, to avoid problems with module reload */
if (musb->xceiv->otg->default_a) {
int maxdelay = 30;
u8 devctl, warn = 0;
/* if there's no peripheral connected, this can take a
* long time to fall, especially on EVM with huge C133.
*/
do {
devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
if (!(devctl & MUSB_DEVCTL_VBUS))
break;
if ((devctl & MUSB_DEVCTL_VBUS) != warn) {
warn = devctl & MUSB_DEVCTL_VBUS;
dev_dbg(musb->controller, "VBUS %d\n",
warn >> MUSB_DEVCTL_VBUS_SHIFT);
}
msleep(1000);
maxdelay--;
} while (maxdelay > 0);
static int davinci_musb_init(struct musb *musb)
{
void __iomem *tibase = musb->ctrl_base;
u32 revision;
int ret = -ENODEV;
usb_nop_xceiv_register();
musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
if (IS_ERR_OR_NULL(musb->xceiv)) {
ret = -EPROBE_DEFER;
goto unregister;
}
musb->mregs += DAVINCI_BASE_OFFSET;
/* returns zero if e.g. not clocked */
revision = musb_readl(tibase, DAVINCI_USB_VERSION_REG);
if (revision == 0)
goto fail;
setup_timer(&otg_workaround, otg_timer, (unsigned long) musb);
davinci_musb_source_power(musb, 0, 1);
/* dm355 EVM swaps D+/D- for signal integrity, and
* is clocked from the main 24 MHz crystal.
*/
if (machine_is_davinci_dm355_evm()) {
u32 phy_ctrl = __raw_readl(USB_PHY_CTRL);
phy_ctrl &= ~(3 << 9);
phy_ctrl |= USBPHY_DATAPOL;
__raw_writel(phy_ctrl, USB_PHY_CTRL);
}
/* On dm355, the default-A state machine needs DRVVBUS control.
* If we won't be a host, there's no need to turn it on.
*/
if (cpu_is_davinci_dm355()) {
u32 deepsleep = __raw_readl(DM355_DEEPSLEEP);
deepsleep &= ~DRVVBUS_FORCE;
__raw_writel(deepsleep, DM355_DEEPSLEEP);
}
/* reset the controller */
musb_writel(tibase, DAVINCI_USB_CTRL_REG, 0x1);
/* start the on-chip PHY and its PLL */
phy_on();
msleep(5);
/* NOTE: irqs are in mixed mode, not bypass to pure-musb */
pr_debug("DaVinci OTG revision %08x phy %03x control %02x\n",
revision, __raw_readl(USB_PHY_CTRL),
musb_readb(tibase, DAVINCI_USB_CTRL_REG));
musb->isr = davinci_musb_interrupt;
return 0;
fail:
usb_put_phy(musb->xceiv);
unregister:
usb_nop_xceiv_unregister();
return ret;
}
static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
struct usb_otg *otg = musb->xceiv->otg;
void __iomem *tibase = musb->ctrl_base;
struct cppi *cppi;
u32 tmp;
spin_lock_irqsave(&musb->lock, flags);
/* NOTE: DaVinci shadows the Mentor IRQs. Don't manage them through
* the Mentor registers (except for setup), use the TI ones and EOI.
*
* Docs describe irq "vector" registers associated with the CPPI and
* USB EOI registers. These hold a bitmask corresponding to the
* current IRQ, not an irq handler address. Would using those bits
* resolve some of the races observed in this dispatch code??
*/
/* CPPI interrupts share the same IRQ line, but have their own
* mask, state, "vector", and EOI registers.
*/
cppi = container_of(musb->dma_controller, struct cppi, controller);
if (is_cppi_enabled() && musb->dma_controller && !cppi->irq)
retval = cppi_interrupt(irq, __hci);
/* ack and handle non-CPPI interrupts */
tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG);
musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp);
dev_dbg(musb->controller, "IRQ %08x\n", tmp);
musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK)
>> DAVINCI_USB_RXINT_SHIFT;
musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK)
>> DAVINCI_USB_TXINT_SHIFT;
musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
>> DAVINCI_USB_USBINT_SHIFT;
/* DRVVBUS irqs are the only proxy we have (a very poor one!) for
* DaVinci's missing ID change IRQ. We need an ID change IRQ to
* switch appropriately between halves of the OTG state machine.
* Managing DEVCTL.SESSION per Mentor docs requires we know its
* value, but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
* Also, DRVVBUS pulses for SRP (but not at 5V) ...
*/
if (tmp & (DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT)) {
int drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err = musb->int_usb & MUSB_INTR_VBUSERROR;
err = musb->int_usb & MUSB_INTR_VBUSERROR;
if (err) {
/* The Mentor core doesn't debounce VBUS as needed
* to cope with device connect current spikes. This
* means it's not uncommon for bus-powered devices
* to get VBUS errors during enumeration.
*
* This is a workaround, but newer RTL from Mentor
* seems to allow a better one: "re"starting sessions
* without waiting (on EVM, a **long** time) for VBUS
* to stop registering in devctl.
*/
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (drvvbus) {
MUSB_HST_MODE(musb);
otg->default_a = 1;
musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
portstate(musb->port1_status |= USB_PORT_STAT_POWER);
del_timer(&otg_workaround);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
otg->default_a = 0;
musb->xceiv->state = OTG_STATE_B_IDLE;
portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
}
/* NOTE: this must complete poweron within 100 msec
* (OTG_TIME_A_WAIT_VRISE) but we don't check for that.
*/
davinci_musb_source_power(musb, drvvbus, 0);
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
usb_otg_state_string(musb->xceiv->state),
err ? " ERROR" : "",
devctl);
retval = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
retval |= musb_interrupt(musb);
/* irq stays asserted until EOI is written */
musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
/* poll for ID change */
if (musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
static void davinci_musb_set_vbus(struct musb *musb, int is_on)
{
WARN_ON(is_on && is_peripheral_active(musb));
davinci_musb_source_power(musb, is_on, 0);
}
static int davinci_musb_init(struct musb *musb)
{
void __iomem *tibase = musb->ctrl_base;
u32 revision;
usb_nop_xceiv_register();
musb->xceiv = usb_get_transceiver();
if (!musb->xceiv)
goto unregister;
musb->mregs += DAVINCI_BASE_OFFSET;
revision = musb_readl(tibase, DAVINCI_USB_VERSION_REG);
if (revision == 0)
goto fail;
if (is_host_enabled(musb))
setup_timer(&otg_workaround, otg_timer, (unsigned long) musb);
davinci_musb_source_power(musb, 0, 1);
if (machine_is_davinci_dm355_evm()) {
u32 phy_ctrl = __raw_readl(USB_PHY_CTRL);
phy_ctrl &= ~(3 << 9);
phy_ctrl |= USBPHY_DATAPOL;
__raw_writel(phy_ctrl, USB_PHY_CTRL);
}
if (cpu_is_davinci_dm355()) {
u32 deepsleep = __raw_readl(DM355_DEEPSLEEP);
if (is_host_enabled(musb)) {
deepsleep &= ~DRVVBUS_OVERRIDE;
} else {
deepsleep &= ~DRVVBUS_FORCE;
deepsleep |= DRVVBUS_OVERRIDE;
}
__raw_writel(deepsleep, DM355_DEEPSLEEP);
}
musb_writel(tibase, DAVINCI_USB_CTRL_REG, 0x1);
phy_on();
msleep(5);
pr_debug("DaVinci OTG revision %08x phy %03x control %02x\n",
revision, __raw_readl(USB_PHY_CTRL),
musb_readb(tibase, DAVINCI_USB_CTRL_REG));
musb->isr = davinci_musb_interrupt;
return 0;
fail:
usb_put_transceiver(musb->xceiv);
unregister:
usb_nop_xceiv_unregister();
return -ENODEV;
}
static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
struct usb_otg *otg = musb->xceiv->otg;
void __iomem *tibase = musb->ctrl_base;
struct cppi *cppi;
u32 tmp;
spin_lock_irqsave(&musb->lock, flags);
cppi = container_of(musb->dma_controller, struct cppi, controller);
if (is_cppi_enabled() && musb->dma_controller && !cppi->irq)
retval = cppi_interrupt(irq, __hci);
tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG);
musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp);
dev_dbg(musb->controller, "IRQ %08x\n", tmp);
musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK)
>> DAVINCI_USB_RXINT_SHIFT;
musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK)
>> DAVINCI_USB_TXINT_SHIFT;
musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
>> DAVINCI_USB_USBINT_SHIFT;
if (tmp & (DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT)) {
int drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err = musb->int_usb & MUSB_INTR_VBUSERROR;
err = is_host_enabled(musb)
&& (musb->int_usb & MUSB_INTR_VBUSERROR);
if (err) {
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (is_host_enabled(musb) && drvvbus) {
MUSB_HST_MODE(musb);
otg->default_a = 1;
musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
portstate(musb->port1_status |= USB_PORT_STAT_POWER);
del_timer(&otg_workaround);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
otg->default_a = 0;
musb->xceiv->state = OTG_STATE_B_IDLE;
portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
}
davinci_musb_source_power(musb, drvvbus, 0);
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
otg_state_string(musb->xceiv->state),
err ? " ERROR" : "",
devctl);
retval = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
retval |= musb_interrupt(musb);
/* irq stays asserted until EOI is written */
musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
if (is_otg_enabled(musb)
&& musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
