int ieee80211_register_hw(struct ieee80211_hw *hw)
{
struct ieee80211_local *local = hw_to_local(hw);
int result, i;
enum ieee80211_band band;
int channels, max_bitrates;
bool supp_ht;
static const u32 cipher_suites[] = {
/* keep WEP first, it may be removed below */
WLAN_CIPHER_SUITE_WEP40,
WLAN_CIPHER_SUITE_WEP104,
WLAN_CIPHER_SUITE_TKIP,
WLAN_CIPHER_SUITE_CCMP,
/* keep last -- depends on hw flags! */
WLAN_CIPHER_SUITE_AES_CMAC
};
if ((hw->wiphy->wowlan.flags || hw->wiphy->wowlan.n_patterns)
#ifdef CONFIG_PM
&& (!local->ops->suspend || !local->ops->resume)
#endif
)
return -EINVAL;
if (hw->max_report_rates == 0)
hw->max_report_rates = hw->max_rates;
/*
* generic code guarantees at least one band,
* set this very early because much code assumes
* that hw.conf.channel is assigned
*/
channels = 0;
max_bitrates = 0;
supp_ht = false;
for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
struct ieee80211_supported_band *sband;
sband = local->hw.wiphy->bands[band];
if (!sband)
continue;
if (!local->oper_channel) {
/* init channel we're on */
local->hw.conf.channel =
local->oper_channel = &sband->channels[0];
local->hw.conf.channel_type = NL80211_CHAN_NO_HT;
}
channels += sband->n_channels;
if (max_bitrates < sband->n_bitrates)
max_bitrates = sband->n_bitrates;
supp_ht = supp_ht || sband->ht_cap.ht_supported;
}
local->int_scan_req = kzalloc(sizeof(*local->int_scan_req) +
sizeof(void *) * channels, GFP_KERNEL);
if (!local->int_scan_req)
return -ENOMEM;
/* if low-level driver supports AP, we also support VLAN */
if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_AP)) {
hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN);
hw->wiphy->software_iftypes |= BIT(NL80211_IFTYPE_AP_VLAN);
}
/* mac80211 always supports monitor */
hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_MONITOR);
hw->wiphy->software_iftypes |= BIT(NL80211_IFTYPE_MONITOR);
/*
* mac80211 doesn't support more than 1 channel, and also not more
* than one IBSS interface
*/
for (i = 0; i < hw->wiphy->n_iface_combinations; i++) {
const struct ieee80211_iface_combination *c;
int j;
c = &hw->wiphy->iface_combinations[i];
if (c->num_different_channels > 1)
return -EINVAL;
for (j = 0; j < c->n_limits; j++)
if ((c->limits[j].types & BIT(NL80211_IFTYPE_ADHOC)) &&
c->limits[j].max > 1)
return -EINVAL;
}
#ifndef CONFIG_MAC80211_MESH
/* mesh depends on Kconfig, but drivers should set it if they want */
local->hw.wiphy->interface_modes &= ~BIT(NL80211_IFTYPE_MESH_POINT);
#endif
/* if the underlying driver supports mesh, mac80211 will (at least)
* provide routing of mesh authentication frames to userspace */
if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_MESH_POINT))
local->hw.wiphy->flags |= WIPHY_FLAG_MESH_AUTH;
/* mac80211 supports control port protocol changing */
local->hw.wiphy->flags |= WIPHY_FLAG_CONTROL_PORT_PROTOCOL;
if (local->hw.flags & IEEE80211_HW_SIGNAL_DBM)
local->hw.wiphy->signal_type = CFG80211_SIGNAL_TYPE_MBM;
else if (local->hw.flags & IEEE80211_HW_SIGNAL_UNSPEC)
local->hw.wiphy->signal_type = CFG80211_SIGNAL_TYPE_UNSPEC;
WARN((local->hw.flags & IEEE80211_HW_SUPPORTS_UAPSD)
&& (local->hw.flags & IEEE80211_HW_PS_NULLFUNC_STACK),
"U-APSD not supported with HW_PS_NULLFUNC_STACK\n");
/*
* Calculate scan IE length -- we need this to alloc
* memory and to subtract from the driver limit. It
* includes the DS Params, (extended) supported rates, and HT
* information -- SSID is the driver's responsibility.
*/
local->scan_ies_len = 4 + max_bitrates /* (ext) supp rates */ +
3 /* DS Params */;
if (supp_ht)
local->scan_ies_len += 2 + sizeof(struct ieee80211_ht_cap);
if (!local->ops->hw_scan) {
/* For hw_scan, driver needs to set these up. */
local->hw.wiphy->max_scan_ssids = 4;
local->hw.wiphy->max_scan_ie_len = IEEE80211_MAX_DATA_LEN;
}
/*
* If the driver supports any scan IEs, then assume the
* limit includes the IEs mac80211 will add, otherwise
* leave it at zero and let the driver sort it out; we
* still pass our IEs to the driver but userspace will
* not be allowed to in that case.
*/
if (local->hw.wiphy->max_scan_ie_len)
local->hw.wiphy->max_scan_ie_len -= local->scan_ies_len;
/* Set up cipher suites unless driver already did */
if (!local->hw.wiphy->cipher_suites) {
local->hw.wiphy->cipher_suites = cipher_suites;
local->hw.wiphy->n_cipher_suites = ARRAY_SIZE(cipher_suites);
if (!(local->hw.flags & IEEE80211_HW_MFP_CAPABLE))
local->hw.wiphy->n_cipher_suites--;
}
if (IS_ERR(local->wep_tx_tfm) || IS_ERR(local->wep_rx_tfm)) {
if (local->hw.wiphy->cipher_suites == cipher_suites) {
local->hw.wiphy->cipher_suites += 2;
local->hw.wiphy->n_cipher_suites -= 2;
} else {
u32 *suites;
int r, w = 0;
/* Filter out WEP */
suites = kmemdup(
local->hw.wiphy->cipher_suites,
sizeof(u32) * local->hw.wiphy->n_cipher_suites,
GFP_KERNEL);
if (!suites)
return -ENOMEM;
for (r = 0; r < local->hw.wiphy->n_cipher_suites; r++) {
u32 suite = local->hw.wiphy->cipher_suites[r];
if (suite == WLAN_CIPHER_SUITE_WEP40 ||
suite == WLAN_CIPHER_SUITE_WEP104)
continue;
suites[w++] = suite;
}
local->hw.wiphy->cipher_suites = suites;
local->hw.wiphy->n_cipher_suites = w;
local->wiphy_ciphers_allocated = true;
}
}
if (!local->ops->remain_on_channel)
local->hw.wiphy->max_remain_on_channel_duration = 5000;
if (local->ops->sched_scan_start)
local->hw.wiphy->flags |= WIPHY_FLAG_SUPPORTS_SCHED_SCAN;
result = wiphy_register(local->hw.wiphy);
if (result < 0)
goto fail_wiphy_register;
/*
* We use the number of queues for feature tests (QoS, HT) internally
* so restrict them appropriately.
*/
if (hw->queues > IEEE80211_MAX_QUEUES)
hw->queues = IEEE80211_MAX_QUEUES;
local->workqueue =
alloc_ordered_workqueue(wiphy_name(local->hw.wiphy), 0);
if (!local->workqueue) {
result = -ENOMEM;
goto fail_workqueue;
}
/*
* The hardware needs headroom for sending the frame,
* and we need some headroom for passing the frame to monitor
* interfaces, but never both at the same time.
*/
#ifndef __CHECKER__
BUILD_BUG_ON(IEEE80211_TX_STATUS_HEADROOM !=
sizeof(struct ieee80211_tx_status_rtap_hdr));
#endif
local->tx_headroom = max_t(unsigned int , local->hw.extra_tx_headroom,
sizeof(struct ieee80211_tx_status_rtap_hdr));
debugfs_hw_add(local);
/*
* if the driver doesn't specify a max listen interval we
* use 5 which should be a safe default
*/
if (local->hw.max_listen_interval == 0)
local->hw.max_listen_interval = 5;
local->hw.conf.listen_interval = local->hw.max_listen_interval;
local->dynamic_ps_forced_timeout = -1;
result = ieee80211_wep_init(local);
if (result < 0)
wiphy_debug(local->hw.wiphy, "Failed to initialize wep: %d\n",
result);
rtnl_lock();
result = ieee80211_init_rate_ctrl_alg(local,
hw->rate_control_algorithm);
if (result < 0) {
wiphy_debug(local->hw.wiphy,
"Failed to initialize rate control algorithm\n");
goto fail_rate;
}
/* add one default STA interface if supported */
if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_STATION)) {
result = ieee80211_if_add(local, "wlan%d", NULL,
NL80211_IFTYPE_STATION, NULL);
if (result)
wiphy_warn(local->hw.wiphy,
"Failed to add default virtual iface\n");
}
rtnl_unlock();
ieee80211_led_init(local);
local->network_latency_notifier.notifier_call =
ieee80211_max_network_latency;
result = pm_qos_add_notifier(PM_QOS_NETWORK_LATENCY,
&local->network_latency_notifier);
if (result) {
rtnl_lock();
goto fail_pm_qos;
}
#ifdef CONFIG_INET
local->ifa_notifier.notifier_call = ieee80211_ifa_changed;
result = register_inetaddr_notifier(&local->ifa_notifier);
if (result)
goto fail_ifa;
#endif
netif_napi_add(&local->napi_dev, &local->napi, ieee80211_napi_poll,
local->hw.napi_weight);
return 0;
#ifdef CONFIG_INET
fail_ifa:
pm_qos_remove_notifier(PM_QOS_NETWORK_LATENCY,
&local->network_latency_notifier);
rtnl_lock();
#endif
fail_pm_qos:
ieee80211_led_exit(local);
ieee80211_remove_interfaces(local);
fail_rate:
rtnl_unlock();
ieee80211_wep_free(local);
sta_info_stop(local);
destroy_workqueue(local->workqueue);
fail_workqueue:
wiphy_unregister(local->hw.wiphy);
fail_wiphy_register:
if (local->wiphy_ciphers_allocated)
kfree(local->hw.wiphy->cipher_suites);
kfree(local->int_scan_req);
return result;
}
int ieee80211_register_hw(struct ieee80211_hw *hw)
{
struct ieee80211_local *local = hw_to_local(hw);
int result;
enum ieee80211_band band;
int channels, max_bitrates;
bool supp_ht;
static const u32 cipher_suites[] = {
WLAN_CIPHER_SUITE_WEP40,
WLAN_CIPHER_SUITE_WEP104,
WLAN_CIPHER_SUITE_TKIP,
WLAN_CIPHER_SUITE_CCMP,
/* keep last -- depends on hw flags! */
WLAN_CIPHER_SUITE_AES_CMAC
};
/*
* generic code guarantees at least one band,
* set this very early because much code assumes
* that hw.conf.channel is assigned
*/
channels = 0;
max_bitrates = 0;
supp_ht = false;
for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
struct ieee80211_supported_band *sband;
sband = local->hw.wiphy->bands[band];
if (!sband)
continue;
if (!local->oper_channel) {
/* init channel we're on */
local->hw.conf.channel =
local->oper_channel = &sband->channels[0];
local->hw.conf.channel_type = NL80211_CHAN_NO_HT;
}
channels += sband->n_channels;
if (max_bitrates < sband->n_bitrates)
max_bitrates = sband->n_bitrates;
supp_ht = supp_ht || sband->ht_cap.ht_supported;
}
local->int_scan_req = kzalloc(sizeof(*local->int_scan_req) +
sizeof(void *) * channels, GFP_KERNEL);
if (!local->int_scan_req)
return -ENOMEM;
/* if low-level driver supports AP, we also support VLAN */
if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_AP))
local->hw.wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN);
/* mac80211 always supports monitor */
local->hw.wiphy->interface_modes |= BIT(NL80211_IFTYPE_MONITOR);
if (local->hw.flags & IEEE80211_HW_SIGNAL_DBM)
local->hw.wiphy->signal_type = CFG80211_SIGNAL_TYPE_MBM;
else if (local->hw.flags & IEEE80211_HW_SIGNAL_UNSPEC)
local->hw.wiphy->signal_type = CFG80211_SIGNAL_TYPE_UNSPEC;
WARN((local->hw.flags & IEEE80211_HW_SUPPORTS_UAPSD)
&& (local->hw.flags & IEEE80211_HW_PS_NULLFUNC_STACK),
"U-APSD not supported with HW_PS_NULLFUNC_STACK\n");
/*
* Calculate scan IE length -- we need this to alloc
* memory and to subtract from the driver limit. It
* includes the (extended) supported rates and HT
* information -- SSID is the driver's responsibility.
*/
local->scan_ies_len = 4 + max_bitrates; /* (ext) supp rates */
if (supp_ht)
local->scan_ies_len += 2 + sizeof(struct ieee80211_ht_cap);
if (!local->ops->hw_scan) {
/* For hw_scan, driver needs to set these up. */
local->hw.wiphy->max_scan_ssids = 4;
local->hw.wiphy->max_scan_ie_len = IEEE80211_MAX_DATA_LEN;
}
/*
* If the driver supports any scan IEs, then assume the
* limit includes the IEs mac80211 will add, otherwise
* leave it at zero and let the driver sort it out; we
* still pass our IEs to the driver but userspace will
* not be allowed to in that case.
*/
if (local->hw.wiphy->max_scan_ie_len)
local->hw.wiphy->max_scan_ie_len -= local->scan_ies_len;
local->hw.wiphy->cipher_suites = cipher_suites;
local->hw.wiphy->n_cipher_suites = ARRAY_SIZE(cipher_suites);
if (!(local->hw.flags & IEEE80211_HW_MFP_CAPABLE))
local->hw.wiphy->n_cipher_suites--;
result = wiphy_register(local->hw.wiphy);
if (result < 0)
goto fail_wiphy_register;
/*
* We use the number of queues for feature tests (QoS, HT) internally
* so restrict them appropriately.
*/
if (hw->queues > IEEE80211_MAX_QUEUES)
hw->queues = IEEE80211_MAX_QUEUES;
local->workqueue =
create_singlethread_workqueue(wiphy_name(local->hw.wiphy));
if (!local->workqueue) {
result = -ENOMEM;
goto fail_workqueue;
}
/*
* The hardware needs headroom for sending the frame,
* and we need some headroom for passing the frame to monitor
* interfaces, but never both at the same time.
*/
BUILD_BUG_ON(IEEE80211_TX_STATUS_HEADROOM !=
sizeof(struct ieee80211_tx_status_rtap_hdr));
local->tx_headroom = max_t(unsigned int , local->hw.extra_tx_headroom,
sizeof(struct ieee80211_tx_status_rtap_hdr));
debugfs_hw_add(local);
/*
* if the driver doesn't specify a max listen interval we
* use 5 which should be a safe default
*/
if (local->hw.max_listen_interval == 0)
local->hw.max_listen_interval = 5;
local->hw.conf.listen_interval = local->hw.max_listen_interval;
local->dynamic_ps_forced_timeout = -1;
result = sta_info_start(local);
if (result < 0)
goto fail_sta_info;
result = ieee80211_wep_init(local);
if (result < 0)
printk(KERN_DEBUG "%s: Failed to initialize wep: %d\n",
wiphy_name(local->hw.wiphy), result);
rtnl_lock();
result = ieee80211_init_rate_ctrl_alg(local,
hw->rate_control_algorithm);
if (result < 0) {
printk(KERN_DEBUG "%s: Failed to initialize rate control "
"algorithm\n", wiphy_name(local->hw.wiphy));
goto fail_rate;
}
/* add one default STA interface if supported */
if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_STATION)) {
result = ieee80211_if_add(local, "wlan%d", NULL,
NL80211_IFTYPE_STATION, NULL);
if (result)
printk(KERN_WARNING "%s: Failed to add default virtual iface\n",
wiphy_name(local->hw.wiphy));
}
rtnl_unlock();
ieee80211_led_init(local);
local->network_latency_notifier.notifier_call =
ieee80211_max_network_latency;
result = pm_qos_add_notifier(PM_QOS_NETWORK_LATENCY,
&local->network_latency_notifier);
if (result) {
rtnl_lock();
goto fail_pm_qos;
}
#ifdef CONFIG_INET
local->ifa_notifier.notifier_call = ieee80211_ifa_changed;
result = register_inetaddr_notifier(&local->ifa_notifier);
if (result)
goto fail_ifa;
#endif
return 0;
#ifdef CONFIG_INET
fail_ifa:
pm_qos_remove_notifier(PM_QOS_NETWORK_LATENCY,
&local->network_latency_notifier);
rtnl_lock();
#endif
fail_pm_qos:
ieee80211_led_exit(local);
ieee80211_remove_interfaces(local);
fail_rate:
rtnl_unlock();
ieee80211_wep_free(local);
sta_info_stop(local);
fail_sta_info:
destroy_workqueue(local->workqueue);
fail_workqueue:
wiphy_unregister(local->hw.wiphy);
fail_wiphy_register:
kfree(local->int_scan_req);
return result;
}