void servoTable(void)
{
// airplane / servo mixes
switch (currentMixerMode) {
case MIXER_CUSTOM_AIRPLANE:
case MIXER_FLYING_WING:
case MIXER_AIRPLANE:
case MIXER_BICOPTER:
case MIXER_CUSTOM_TRI:
case MIXER_TRI:
case MIXER_DUALCOPTER:
case MIXER_SINGLECOPTER:
case MIXER_GIMBAL:
servoMixer();
break;
/*
case MIXER_GIMBAL:
servo[SERVO_GIMBAL_PITCH] = (((int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch) / 50) + determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = (((int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll) / 50) + determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
break;
*/
default:
break;
}
// camera stabilization
if (feature(FEATURE_SERVO_TILT)) {
// center at fixed position, or vary either pitch or roll by RC channel
servo[SERVO_GIMBAL_PITCH] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
if (IS_RC_MODE_ACTIVE(BOXCAMSTAB)) {
if (gimbalConfig->mode == GIMBAL_MODE_MIXTILT) {
servo[SERVO_GIMBAL_PITCH] -= (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 - (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
servo[SERVO_GIMBAL_ROLL] += (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 + (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
} else {
servo[SERVO_GIMBAL_PITCH] += (int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch / 50;
servo[SERVO_GIMBAL_ROLL] += (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
}
}
}
// constrain servos
for (int i = 0; i < MAX_SUPPORTED_SERVOS; i++) {
servo[i] = constrain(servo[i], servoConf[i].min, servoConf[i].max); // limit the values
}
}
void processServoTilt(void) {
// center at fixed position, or vary either pitch or roll by RC channel
servo[SERVO_GIMBAL_PITCH] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
if (IS_RC_MODE_ACTIVE(BOXCAMSTAB)) {
if (gimbalConfig->mode == GIMBAL_MODE_MIXTILT) {
servo[SERVO_GIMBAL_PITCH] -= (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 - (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
servo[SERVO_GIMBAL_ROLL] += (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 + (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
} else {
servo[SERVO_GIMBAL_PITCH] += (int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch / 50;
servo[SERVO_GIMBAL_ROLL] += (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
}
}
}
void mixTable(void)
{
uint32_t i;
if (motorCount >= 4 && mixerConfig->yaw_jump_prevention_limit < YAW_JUMP_PREVENTION_LIMIT_HIGH) {
// prevent "yaw jump" during yaw correction
axisPID[YAW] = constrain(axisPID[YAW], -mixerConfig->yaw_jump_prevention_limit - ABS(rcCommand[YAW]), mixerConfig->yaw_jump_prevention_limit + ABS(rcCommand[YAW]));
}
// motors for non-servo mixes
for (i = 0; i < motorCount; i++) {
motor[i] =
rcCommand[THROTTLE] * currentMixer[i].throttle +
axisPID[PITCH] * currentMixer[i].pitch +
axisPID[ROLL] * currentMixer[i].roll +
-mixerConfig->yaw_motor_direction * axisPID[YAW] * currentMixer[i].yaw;
}
if (ARMING_FLAG(ARMED)) {
bool isFailsafeActive = failsafeIsActive();
// Find the maximum motor output.
int16_t maxMotor = motor[0];
for (i = 1; i < motorCount; i++) {
// If one motor is above the maxthrottle threshold, we reduce the value
// of all motors by the amount of overshoot. That way, only one motor
// is at max and the relative power of each motor is preserved.
if (motor[i] > maxMotor) {
maxMotor = motor[i];
}
}
int16_t maxThrottleDifference = 0;
if (maxMotor > escAndServoConfig->maxthrottle) {
maxThrottleDifference = maxMotor - escAndServoConfig->maxthrottle;
}
for (i = 0; i < motorCount; i++) {
// this is a way to still have good gyro corrections if at least one motor reaches its max.
motor[i] -= maxThrottleDifference;
if (feature(FEATURE_3D)) {
if (mixerConfig->pid_at_min_throttle
|| rcData[THROTTLE] <= rxConfig->midrc - flight3DConfig->deadband3d_throttle
|| rcData[THROTTLE] >= rxConfig->midrc + flight3DConfig->deadband3d_throttle) {
if (rcData[THROTTLE] > rxConfig->midrc) {
motor[i] = constrain(motor[i], flight3DConfig->deadband3d_high, escAndServoConfig->maxthrottle);
} else {
motor[i] = constrain(motor[i], escAndServoConfig->mincommand, flight3DConfig->deadband3d_low);
}
} else {
if (rcData[THROTTLE] > rxConfig->midrc) {
motor[i] = flight3DConfig->deadband3d_high;
} else {
motor[i] = flight3DConfig->deadband3d_low;
}
}
} else {
if (isFailsafeActive) {
motor[i] = constrain(motor[i], escAndServoConfig->mincommand, escAndServoConfig->maxthrottle);
} else {
// If we're at minimum throttle and FEATURE_MOTOR_STOP enabled,
// do not spin the motors.
motor[i] = constrain(motor[i], escAndServoConfig->minthrottle, escAndServoConfig->maxthrottle);
if ((rcData[THROTTLE]) < rxConfig->mincheck) {
if (feature(FEATURE_MOTOR_STOP)) {
motor[i] = escAndServoConfig->mincommand;
} else if (mixerConfig->pid_at_min_throttle == 0) {
motor[i] = escAndServoConfig->minthrottle;
}
}
}
}
}
} else {
for (i = 0; i < motorCount; i++) {
motor[i] = motor_disarmed[i];
}
}
// motor outputs are used as sources for servo mixing, so motors must be calculated before servos.
#if !defined(USE_QUAD_MIXER_ONLY) && defined(USE_SERVOS)
// airplane / servo mixes
switch (currentMixerMode) {
case MIXER_CUSTOM_AIRPLANE:
case MIXER_FLYING_WING:
case MIXER_AIRPLANE:
case MIXER_BICOPTER:
case MIXER_CUSTOM_TRI:
case MIXER_TRI:
case MIXER_DUALCOPTER:
case MIXER_SINGLECOPTER:
case MIXER_GIMBAL:
servoMixer();
break;
/*
case MIXER_GIMBAL:
servo[SERVO_GIMBAL_PITCH] = (((int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch) / 50) + determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = (((int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll) / 50) + determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
break;
*/
default:
break;
}
// camera stabilization
if (feature(FEATURE_SERVO_TILT)) {
// center at fixed position, or vary either pitch or roll by RC channel
servo[SERVO_GIMBAL_PITCH] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
if (IS_RC_MODE_ACTIVE(BOXCAMSTAB)) {
if (gimbalConfig->mode == GIMBAL_MODE_MIXTILT) {
servo[SERVO_GIMBAL_PITCH] -= (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 - (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
servo[SERVO_GIMBAL_ROLL] += (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 + (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
} else {
servo[SERVO_GIMBAL_PITCH] += (int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch / 50;
servo[SERVO_GIMBAL_ROLL] += (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
}
}
}
// constrain servos
for (i = 0; i < MAX_SUPPORTED_SERVOS; i++) {
servo[i] = constrain(servo[i], servoConf[i].min, servoConf[i].max); // limit the values
}
#endif
}
STATIC_UNIT_TESTED void servoMixer(void)
{
int16_t input[INPUT_SOURCE_COUNT]; // Range [-500:+500]
static int16_t currentOutput[MAX_SERVO_RULES];
uint8_t i;
if (FLIGHT_MODE(PASSTHRU_MODE)) {
// Direct passthru from RX
input[INPUT_STABILIZED_ROLL] = rcCommand[ROLL];
input[INPUT_STABILIZED_PITCH] = rcCommand[PITCH];
input[INPUT_STABILIZED_YAW] = rcCommand[YAW];
} else {
// Assisted modes (gyro only or gyro+acc according to AUX configuration in Gui
input[INPUT_STABILIZED_ROLL] = axisPID[ROLL];
input[INPUT_STABILIZED_PITCH] = axisPID[PITCH];
input[INPUT_STABILIZED_YAW] = axisPID[YAW];
// Reverse yaw servo when inverted in 3D mode
if (feature(FEATURE_3D) && (rcData[THROTTLE] < rxConfig->midrc)) {
input[INPUT_STABILIZED_YAW] *= -1;
}
}
input[INPUT_GIMBAL_PITCH] = scaleRange(attitude.values.pitch, -1800, 1800, -500, +500);
input[INPUT_GIMBAL_ROLL] = scaleRange(attitude.values.roll, -1800, 1800, -500, +500);
input[INPUT_STABILIZED_THROTTLE] = motor[0] - 1000 - 500; // Since it derives from rcCommand or mincommand and must be [-500:+500]
// center the RC input value around the RC middle value
// by subtracting the RC middle value from the RC input value, we get:
// data - middle = input
// 2000 - 1500 = +500
// 1500 - 1500 = 0
// 1000 - 1500 = -500
input[INPUT_RC_ROLL] = rcData[ROLL] - rxConfig->midrc;
input[INPUT_RC_PITCH] = rcData[PITCH] - rxConfig->midrc;
input[INPUT_RC_YAW] = rcData[YAW] - rxConfig->midrc;
input[INPUT_RC_THROTTLE] = rcData[THROTTLE] - rxConfig->midrc;
input[INPUT_RC_AUX1] = rcData[AUX1] - rxConfig->midrc;
input[INPUT_RC_AUX2] = rcData[AUX2] - rxConfig->midrc;
input[INPUT_RC_AUX3] = rcData[AUX3] - rxConfig->midrc;
input[INPUT_RC_AUX4] = rcData[AUX4] - rxConfig->midrc;
for (i = 0; i < MAX_SUPPORTED_SERVOS; i++)
servo[i] = 0;
// mix servos according to rules
for (i = 0; i < servoRuleCount; i++) {
// consider rule if no box assigned or box is active
if (currentServoMixer[i].box == 0 || IS_RC_MODE_ACTIVE(BOXSERVO1 + currentServoMixer[i].box - 1)) {
uint8_t target = currentServoMixer[i].targetChannel;
uint8_t from = currentServoMixer[i].inputSource;
uint16_t servo_width = servoConf[target].max - servoConf[target].min;
int16_t min = currentServoMixer[i].min * servo_width / 100 - servo_width / 2;
int16_t max = currentServoMixer[i].max * servo_width / 100 - servo_width / 2;
if (currentServoMixer[i].speed == 0)
currentOutput[i] = input[from];
else {
if (currentOutput[i] < input[from])
currentOutput[i] = constrain(currentOutput[i] + currentServoMixer[i].speed, currentOutput[i], input[from]);
else if (currentOutput[i] > input[from])
currentOutput[i] = constrain(currentOutput[i] - currentServoMixer[i].speed, input[from], currentOutput[i]);
}
servo[target] += servoDirection(target, from) * constrain(((int32_t)currentOutput[i] * currentServoMixer[i].rate) / 100, min, max);
} else {
currentOutput[i] = 0;
}
}
for (i = 0; i < MAX_SUPPORTED_SERVOS; i++) {
servo[i] = ((int32_t)servoConf[i].rate * servo[i]) / 100L;
servo[i] += determineServoMiddleOrForwardFromChannel(i);
}
}
void mixTable(void *pidProfilePtr)
{
uint32_t i = 0;
fix12_t vbatCompensationFactor = 0;
static fix12_t mixReduction;
bool use_vbat_compensation = false;
pidProfile_t *pidProfile = (pidProfile_t *) pidProfilePtr;
if (batteryConfig && pidProfile->vbatPidCompensation) {
use_vbat_compensation = true;
vbatCompensationFactor = calculateVbatPidCompensation();
}
bool isFailsafeActive = failsafeIsActive(); // TODO - Find out if failsafe checks are really needed here in mixer code
// Initial mixer concept by bdoiron74 reused and optimized for Air Mode
int16_t rollPitchYawMix[MAX_SUPPORTED_MOTORS];
int16_t rollPitchYawMixMax = 0; // assumption: symetrical about zero.
int16_t rollPitchYawMixMin = 0;
if (use_vbat_compensation) rollPitchYawMix[i] = qMultiply(vbatCompensationFactor, rollPitchYawMix[i]); // Add voltage compensation
// Find roll/pitch/yaw desired output
for (i = 0; i < motorCount; i++) {
rollPitchYawMix[i] =
axisPID[PITCH] * currentMixer[i].pitch +
axisPID[ROLL] * currentMixer[i].roll +
-mixerConfig->yaw_motor_direction * axisPID[YAW] * currentMixer[i].yaw;
if (use_vbat_compensation) rollPitchYawMix[i] = qMultiply(vbatCompensationFactor, rollPitchYawMix[i]); // Add voltage compensation
if (rollPitchYawMix[i] > rollPitchYawMixMax) rollPitchYawMixMax = rollPitchYawMix[i];
if (rollPitchYawMix[i] < rollPitchYawMixMin) rollPitchYawMixMin = rollPitchYawMix[i];
if (debugMode == DEBUG_MIXER && i < 5) debug[i] = rollPitchYawMix[i];
}
// Scale roll/pitch/yaw uniformly to fit within throttle range
int16_t rollPitchYawMixRange = rollPitchYawMixMax - rollPitchYawMixMin;
int16_t throttleRange, throttle;
int16_t throttleMin, throttleMax;
static int16_t throttlePrevious = 0; // Store the last throttle direction for deadband transitions
// Find min and max throttle based on condition.
if (feature(FEATURE_3D)) {
if (!ARMING_FLAG(ARMED)) throttlePrevious = rxConfig->midrc; // When disarmed set to mid_rc. It always results in positive direction after arming.
if ((rcCommand[THROTTLE] <= (rxConfig->midrc - flight3DConfig->deadband3d_throttle))) { // Out of band handling
throttleMax = flight3DConfig->deadband3d_low;
throttleMin = escAndServoConfig->minthrottle;
throttlePrevious = throttle = rcCommand[THROTTLE];
} else if (rcCommand[THROTTLE] >= (rxConfig->midrc + flight3DConfig->deadband3d_throttle)) { // Positive handling
throttleMax = escAndServoConfig->maxthrottle;
throttleMin = flight3DConfig->deadband3d_high;
throttlePrevious = throttle = rcCommand[THROTTLE];
} else if ((throttlePrevious <= (rxConfig->midrc - flight3DConfig->deadband3d_throttle))) { // Deadband handling from negative to positive
throttle = throttleMax = flight3DConfig->deadband3d_low;
throttleMin = escAndServoConfig->minthrottle;
} else { // Deadband handling from positive to negative
throttleMax = escAndServoConfig->maxthrottle;
throttle = throttleMin = flight3DConfig->deadband3d_high;
}
} else {
throttle = rcCommand[THROTTLE];
throttleMin = escAndServoConfig->minthrottle;
throttleMax = escAndServoConfig->maxthrottle;
}
throttleRange = throttleMax - throttleMin;
if (rollPitchYawMixRange > throttleRange) {
mixReduction = qConstruct(throttleRange, rollPitchYawMixRange);
for (i = 0; i < motorCount; i++) {
rollPitchYawMix[i] = qMultiply(mixReduction,rollPitchYawMix[i]);
}
// Get the maximum correction by setting offset to center
throttleMin = throttleMax = throttleMin + (throttleRange / 2);
} else {
throttleMin = throttleMin + (rollPitchYawMixRange / 2);
throttleMax = throttleMax - (rollPitchYawMixRange / 2);
}
// Now add in the desired throttle, but keep in a range that doesn't clip adjusted
// roll/pitch/yaw. This could move throttle down, but also up for those low throttle flips.
for (i = 0; i < motorCount; i++) {
motor[i] = rollPitchYawMix[i] + constrain(throttle * currentMixer[i].throttle, throttleMin, throttleMax);
if (isFailsafeActive) {
motor[i] = constrain(motor[i], escAndServoConfig->mincommand, escAndServoConfig->maxthrottle);
} else if (feature(FEATURE_3D)) {
if (throttlePrevious <= (rxConfig->midrc - flight3DConfig->deadband3d_throttle)) {
motor[i] = constrain(motor[i], escAndServoConfig->minthrottle, flight3DConfig->deadband3d_low);
} else {
motor[i] = constrain(motor[i], flight3DConfig->deadband3d_high, escAndServoConfig->maxthrottle);
}
} else {
motor[i] = constrain(motor[i], escAndServoConfig->minthrottle, escAndServoConfig->maxthrottle);
}
// Motor stop handling
if (feature(FEATURE_MOTOR_STOP) && ARMING_FLAG(ARMED) && !feature(FEATURE_3D) && !isAirmodeActive()) {
if (((rcData[THROTTLE]) < rxConfig->mincheck)) {
motor[i] = escAndServoConfig->mincommand;
}
}
}
// Disarmed mode
if (!ARMING_FLAG(ARMED)) {
for (i = 0; i < motorCount; i++) {
motor[i] = motor_disarmed[i];
}
}
// motor outputs are used as sources for servo mixing, so motors must be calculated before servos.
#if !defined(USE_QUAD_MIXER_ONLY) || defined(USE_SERVOS)
// airplane / servo mixes
switch (currentMixerMode) {
case MIXER_CUSTOM_AIRPLANE:
case MIXER_FLYING_WING:
case MIXER_AIRPLANE:
case MIXER_BICOPTER:
case MIXER_CUSTOM_TRI:
case MIXER_TRI:
case MIXER_DUALCOPTER:
case MIXER_SINGLECOPTER:
case MIXER_GIMBAL:
servoMixer();
break;
/*
case MIXER_GIMBAL:
servo[SERVO_GIMBAL_PITCH] = (((int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch) / 50) + determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = (((int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll) / 50) + determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
break;
*/
default:
break;
}
// camera stabilization
if (feature(FEATURE_SERVO_TILT)) {
// center at fixed position, or vary either pitch or roll by RC channel
servo[SERVO_GIMBAL_PITCH] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_PITCH);
servo[SERVO_GIMBAL_ROLL] = determineServoMiddleOrForwardFromChannel(SERVO_GIMBAL_ROLL);
if (IS_RC_MODE_ACTIVE(BOXCAMSTAB)) {
if (gimbalConfig->mode == GIMBAL_MODE_MIXTILT) {
servo[SERVO_GIMBAL_PITCH] -= (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 - (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
servo[SERVO_GIMBAL_ROLL] += (-(int32_t)servoConf[SERVO_GIMBAL_PITCH].rate) * attitude.values.pitch / 50 + (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
} else {
servo[SERVO_GIMBAL_PITCH] += (int32_t)servoConf[SERVO_GIMBAL_PITCH].rate * attitude.values.pitch / 50;
servo[SERVO_GIMBAL_ROLL] += (int32_t)servoConf[SERVO_GIMBAL_ROLL].rate * attitude.values.roll / 50;
}
}
}
// constrain servos
for (i = 0; i < MAX_SUPPORTED_SERVOS; i++) {
servo[i] = constrain(servo[i], servoConf[i].min, servoConf[i].max); // limit the values
}
#endif
}
