/**
* dwc3_core_init - Low-level initialization of DWC3 Core
* @dwc: Pointer to our controller context structure
*
* Returns 0 on success otherwise negative errno.
*/
static int dwc3_core_init(struct dwc3 *dwc)
{
u32 reg;
int ret;
if (!dwc3_core_is_valid(dwc)) {
dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n");
ret = -ENODEV;
goto err0;
}
/*
* Write Linux Version Code to our GUID register so it's easy to figure
* out which kernel version a bug was found.
*/
dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE);
/* Handle USB2.0-only core configuration */
if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
DWC3_GHWPARAMS3_SSPHY_IFC_DIS) {
if (dwc->maximum_speed == USB_SPEED_SUPER)
dwc->maximum_speed = USB_SPEED_HIGH;
}
ret = dwc3_core_soft_reset(dwc);
if (ret)
goto err0;
ret = dwc3_phy_setup(dwc);
if (ret)
goto err0;
dwc3_core_setup_global_control(dwc);
dwc3_core_num_eps(dwc);
ret = dwc3_setup_scratch_buffers(dwc);
if (ret)
goto err1;
/* Adjust Frame Length */
dwc3_frame_length_adjustment(dwc);
usb_phy_set_suspend(dwc->usb2_phy, 0);
usb_phy_set_suspend(dwc->usb3_phy, 0);
ret = phy_power_on(dwc->usb2_generic_phy);
if (ret < 0)
goto err2;
ret = phy_power_on(dwc->usb3_generic_phy);
if (ret < 0)
goto err3;
ret = dwc3_event_buffers_setup(dwc);
if (ret) {
dev_err(dwc->dev, "failed to setup event buffers\n");
goto err4;
}
/*
* ENDXFER polling is available on version 3.10a and later of
* the DWC_usb3 controller. It is NOT available in the
* DWC_usb31 controller.
*/
if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
reg |= DWC3_GUCTL2_RST_ACTBITLATER;
dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
}
/*
* Enable hardware control of sending remote wakeup in HS when
* the device is in the L1 state.
*/
if (dwc->revision >= DWC3_REVISION_290A) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW;
dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
}
return 0;
err4:
phy_power_off(dwc->usb3_generic_phy);
err3:
phy_power_off(dwc->usb2_generic_phy);
err2:
usb_phy_set_suspend(dwc->usb2_phy, 1);
usb_phy_set_suspend(dwc->usb3_phy, 1);
err1:
usb_phy_shutdown(dwc->usb2_phy);
usb_phy_shutdown(dwc->usb3_phy);
phy_exit(dwc->usb2_generic_phy);
phy_exit(dwc->usb3_generic_phy);
err0:
return ret;
}
/**
* dwc3_core_init - Low-level initialization of DWC3 Core
* @dwc: Pointer to our controller context structure
*
* Returns 0 on success otherwise negative errno.
*/
int dwc3_core_init(struct dwc3 *dwc)
{
u32 reg;
int ret;
if (!dwc3_core_is_valid(dwc)) {
dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n");
ret = -ENODEV;
goto err0;
}
/*
* Write Linux Version Code to our GUID register so it's easy to figure
* out which kernel version a bug was found.
*/
dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE);
/* Handle USB2.0-only core configuration */
if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
DWC3_GHWPARAMS3_SSPHY_IFC_DIS) {
if (dwc->maximum_speed == USB_SPEED_SUPER)
dwc->maximum_speed = USB_SPEED_HIGH;
}
ret = dwc3_phy_setup(dwc);
if (ret)
goto err0;
if (!dwc->ulpi_ready) {
ret = dwc3_core_ulpi_init(dwc);
if (ret)
goto err0;
dwc->ulpi_ready = true;
}
if (!dwc->phys_ready) {
ret = dwc3_core_get_phy(dwc);
if (ret)
goto err0a;
dwc->phys_ready = true;
}
ret = dwc3_core_soft_reset(dwc);
if (ret)
goto err0a;
dwc3_core_setup_global_control(dwc);
dwc3_core_num_eps(dwc);
if (dwc->scratchbuf == NULL) {
ret = dwc3_alloc_scratch_buffers(dwc);
if (ret) {
dev_err(dwc->dev,
"Not enough memory for scratch buffers\n");
goto err1;
}
}
ret = dwc3_setup_scratch_buffers(dwc);
if (ret) {
dev_err(dwc->dev, "Failed to setup scratch buffers: %d\n", ret);
goto err1;
}
/* Adjust Frame Length */
dwc3_frame_length_adjustment(dwc);
dwc3_set_incr_burst_type(dwc);
ret = dwc3_config_soc_bus(dwc);
if (ret)
goto err1;
usb_phy_set_suspend(dwc->usb2_phy, 0);
usb_phy_set_suspend(dwc->usb3_phy, 0);
ret = phy_power_on(dwc->usb2_generic_phy);
if (ret < 0)
goto err2;
ret = phy_power_on(dwc->usb3_generic_phy);
if (ret < 0)
goto err3;
ret = dwc3_event_buffers_setup(dwc);
if (ret) {
dev_err(dwc->dev, "failed to setup event buffers\n");
goto err4;
}
switch (dwc->dr_mode) {
case USB_DR_MODE_PERIPHERAL:
dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
break;
case USB_DR_MODE_HOST:
dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
break;
case USB_DR_MODE_OTG:
dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG);
break;
default:
dev_warn(dwc->dev, "Unsupported mode %d\n", dwc->dr_mode);
break;
}
/*
* ENDXFER polling is available on version 3.10a and later of
* the DWC_usb3 controller. It is NOT available in the
* DWC_usb31 controller.
*/
if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
reg |= DWC3_GUCTL2_RST_ACTBITLATER;
dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
}
/* When configured in HOST mode, after issuing U3/L2 exit controller
* fails to send proper CRC checksum in CRC5 feild. Because of this
* behaviour Transaction Error is generated, resulting in reset and
* re-enumeration of usb device attached. Enabling bit 10 of GUCTL1
* will correct this problem
*/
if (dwc->enable_guctl1_resume_quirk) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
reg |= DWC3_GUCTL1_RESUME_QUIRK;
dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
}
/* SNPS controller when configureed in HOST mode maintains Inter Packet
* Delay (IPD) of ~380ns which works with most of the super-speed hubs
* except VIA-LAB hubs. When IPD is ~380ns HOST controller fails to
* enumerate FS/LS devices when connected behind VIA-LAB hubs.
* Enabling bit 9 of GUCTL1 enables the workaround in HW to reduce the
* ULPI clock latency by 1 cycle, thus reducing the IPD (~360ns) and
* making controller enumerate FS/LS devices connected behind VIA-LAB.
*/
if (dwc->enable_guctl1_ipd_quirk) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
reg |= DWC3_GUCTL1_IPD_QUIRK;
dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
}
if (dwc->revision >= DWC3_REVISION_250A) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
/*
* Enable hardware control of sending remote wakeup
* in HS when the device is in the L1 state.
*/
if (dwc->revision >= DWC3_REVISION_290A)
reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW;
if (dwc->dis_tx_ipgap_linecheck_quirk)
reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS;
dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
}
if (dwc->dr_mode == USB_DR_MODE_HOST ||
dwc->dr_mode == USB_DR_MODE_OTG) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
/*
* Enable Auto retry Feature to make the controller operating in
* Host mode on seeing transaction errors(CRC errors or internal
* overrun scenerios) on IN transfers to reply to the device
* with a non-terminating retry ACK (i.e, an ACK transcation
* packet with Retry=1 & Nump != 0)
*/
reg |= DWC3_GUCTL_HSTINAUTORETRY;
dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
}
/*
* Must config both number of packets and max burst settings to enable
* RX and/or TX threshold.
*/
if (dwc3_is_usb31(dwc) && dwc->dr_mode == USB_DR_MODE_HOST) {
u8 rx_thr_num = dwc->rx_thr_num_pkt_prd;
u8 rx_maxburst = dwc->rx_max_burst_prd;
u8 tx_thr_num = dwc->tx_thr_num_pkt_prd;
u8 tx_maxburst = dwc->tx_max_burst_prd;
if (rx_thr_num && rx_maxburst) {
reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG);
reg |= DWC31_RXTHRNUMPKTSEL_PRD;
reg &= ~DWC31_RXTHRNUMPKT_PRD(~0);
reg |= DWC31_RXTHRNUMPKT_PRD(rx_thr_num);
reg &= ~DWC31_MAXRXBURSTSIZE_PRD(~0);
reg |= DWC31_MAXRXBURSTSIZE_PRD(rx_maxburst);
dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg);
}
if (tx_thr_num && tx_maxburst) {
reg = dwc3_readl(dwc->regs, DWC3_GTXTHRCFG);
reg |= DWC31_TXTHRNUMPKTSEL_PRD;
reg &= ~DWC31_TXTHRNUMPKT_PRD(~0);
reg |= DWC31_TXTHRNUMPKT_PRD(tx_thr_num);
reg &= ~DWC31_MAXTXBURSTSIZE_PRD(~0);
reg |= DWC31_MAXTXBURSTSIZE_PRD(tx_maxburst);
dwc3_writel(dwc->regs, DWC3_GTXTHRCFG, reg);
}
}
return 0;
err4:
phy_power_off(dwc->usb3_generic_phy);
err3:
phy_power_off(dwc->usb2_generic_phy);
err2:
usb_phy_set_suspend(dwc->usb2_phy, 1);
usb_phy_set_suspend(dwc->usb3_phy, 1);
err1:
usb_phy_shutdown(dwc->usb2_phy);
usb_phy_shutdown(dwc->usb3_phy);
phy_exit(dwc->usb2_generic_phy);
phy_exit(dwc->usb3_generic_phy);
err0a:
dwc3_ulpi_exit(dwc);
err0:
return ret;
}
