Exemplos de eeprom_read_bytes em C++ (Cpp)

Exemplo n.º 1

Arquivo: master-slave-spi.c Projeto: chaitan3/Pratham

void read_frame_from_eeprom(uint8_t *frame)
{
  eeprom_read_bytes(read_addr, FRAME_SIZE, frame);
  read_addr += FRAME_SIZE;
  
  if(read_addr + FRAME_SIZE > MAX_ADDR)
    read_addr = 0;
}

Exemplo n.º 2

Arquivo: host_addr.c Projeto: busyStone/radio_rf

void host_chip_id_read(uint8_t *dst, uint8_t len)
{
    (void)eeprom_read_bytes(&host_addr_i2c, 0, dst, len);

    dst[0] = 0x11;
    dst[1] = 0x22;
    dst[2] = 0x33;
    dst[3] = 0x44;
    return;
}

Exemplo n.º 3

Arquivo: iotoaster.cpp Projeto: brenovit/Radioino

void IOToaster::loadConfiguration()
{
	// Server port
	eeprom_read_bytes(2, (byte *)&_serverPort, sizeof(int));
	// Server Address
	_serverIp = "";
	int addr = sizeof(int) + 3;
	char c;
	do {
		c = eeprom_read_byte((unsigned char *)addr++);
		if (c != 0)
			_serverIp += c;
	} while (c != 0 && addr < 50);
}

Exemplo n.º 4

Arquivo: eeprom.c Projeto: songbangyan/MDK_contiki

void eeprom_read(uint32_t addr,uint16_t num,uint8_t *p_data)
{
#ifdef SPIMARM
  eeprom_status = 1;
  SPIMRAM_ReadBuffer(p_data, addr, num);
#else
  u16 temp_addr;
  u16 temp_num;
  eeprom_status = 1;
  if(addr&0x10000)
  {
    SEL_CHIP2;
    temp_addr = (addr&0xffff);
    temp_num = num;
    eeprom_read_bytes(temp_addr,temp_num,p_data);
  }else if((addr + num)&0x10000)
  {
    SEL_CHIP1;
    temp_addr = (addr&0xffff);
    temp_num = 0x10000 - temp_addr;
    eeprom_read_bytes(temp_addr,temp_num,p_data);
    SEL_CHIP2;
    eeprom_read_bytes(0,num-temp_num,p_data+temp_num);
  }else
  {
    SEL_CHIP1;
    temp_addr = (addr&0xffff);
    temp_num = num;
    eeprom_read_bytes(temp_addr,temp_num,p_data);
  } 
#endif  
  eeprom_status = 0;
  if(wait_eeprom_idle == 1)
  {
    wait_eeprom_idle = 0;
  }
}

Exemplo n.º 5

Arquivo: pairing_list.c Projeto: cansonlee/radio_rf

int32_t pairing_list_addr_read(uint8_t rx_num, uint8_t *addr)
{
    uint8_t eeprom_addr;

    if (rx_num >= PAIRING_LIST_MAX_ADDR_NUM)
    {
        printf("[%s, L%d] rx num(%d) excess max.\r\n", __FILE__, __LINE__, rx_num);
        return -1;
    }
      
    eeprom_addr = PAIRING_LIST_ADDR_LEN * rx_num;
    (void)eeprom_read_bytes(&eeprom_i2c, eeprom_addr, addr, PAIRING_LIST_ADDR_LEN);

    return 0;    
}

Exemplo n.º 6

Arquivo: EepromUtil.cpp Projeto: gaelj/UGS-Preamp_Firmware

//
// Reads an integer value at the specified address.
// Returns true if the variable is successfully read.
// Returns false if the specified address is outside the
// allowed range or too close to the maximum vlaue
// to hold all of the bytes (an int variable requires
// more than one byte).
//
boolean EepromUtil::eeprom_read_int(int addr, int* value) {
  return (eeprom_read_bytes(addr, (byte*)value, sizeof(int)));
}

Exemplo n.º 7

Arquivo: SkynetClient.cpp Projeto: jaehong/skynet_firmware_arduino

void SkynetClient::getUuid(char *uuid)
{
	eeprom_read_bytes(UUIDADDRESS, uuid, UUIDSIZE);
	uuid[UUIDSIZE-1]='\0'; //in case courrupted or not defined
}

Exemplo n.º 8

Arquivo: SkynetClient.cpp Projeto: jaehong/skynet_firmware_arduino

void SkynetClient::getToken(char *token)
{
	eeprom_read_bytes(TOKENADDRESS, token, TOKENSIZE);
	token[TOKENSIZE-1]='\0'; //in case courrupted or not defined
}