Exemplos de enable_norboot_pin_mux em C++ (Cpp)

Exemplo n.º 1

Arquivo: board.c Projeto: guileschool/BEAGLEBONE-tutorials

void s_init(void)
{
	/*
	 * The ROM will only have set up sufficient pinmux to allow for the
	 * first 4KiB NOR to be read, we must finish doing what we know of
	 * the NOR mux in this space in order to continue.
	 */
#ifdef CONFIG_NOR_BOOT
	enable_norboot_pin_mux();
#endif
	watchdog_disable();
	set_uart_mux_conf();
	setup_clocks_for_console();
	uart_soft_reset();
#if defined(CONFIG_NOR_BOOT) || defined(CONFIG_QSPI_BOOT)
	/* TODO: This does not work, gd is not available yet */
	gd->baudrate = CONFIG_BAUDRATE;
	serial_init();
	gd->have_console = 1;
#endif
#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC)
	/* Enable RTC32K clock */
	rtc32k_enable();
#endif
}

Exemplo n.º 2

Arquivo: board.c Projeto: RobertCNelson/u-boot-boards

void early_system_init(void)
{
	/*
	 * The ROM will only have set up sufficient pinmux to allow for the
	 * first 4KiB NOR to be read, we must finish doing what we know of
	 * the NOR mux in this space in order to continue.
	 */
#ifdef CONFIG_NOR_BOOT
	enable_norboot_pin_mux();
#endif
	watchdog_disable();
	set_uart_mux_conf();
	setup_early_clocks();
	uart_soft_reset();
#ifdef CONFIG_SPL_BUILD
	/*
	 * Save the boot parameters passed from romcode.
	 * We cannot delay the saving further than this,
	 * to prevent overwrites.
	 */
	save_omap_boot_params();
#endif
#ifdef CONFIG_DEBUG_UART_OMAP
	debug_uart_init();
#endif
#ifdef CONFIG_TI_I2C_BOARD_DETECT
	do_board_detect();
#endif
#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC)
	/* Enable RTC32K clock */
	rtc32k_enable();
#endif
}

Exemplo n.º 3

Arquivo: board.c Projeto: bradbishop/u-boot

void s_init(void)
{
	/*
	 * The ROM will only have set up sufficient pinmux to allow for the
	 * first 4KiB NOR to be read, we must finish doing what we know of
	 * the NOR mux in this space in order to continue.
	 */
#ifdef CONFIG_NOR_BOOT
	enable_norboot_pin_mux();
#endif
	watchdog_disable();
	set_uart_mux_conf();
	setup_clocks_for_console();
	uart_soft_reset();
#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC)
	/* Enable RTC32K clock */
	rtc32k_enable();
#endif
}

Exemplo n.º 4

Arquivo: board.c Projeto: fanyukui/uboot-2013

void s_init(void)
{
	/*
	 * The ROM will only have set up sufficient pinmux to allow for the
	 * first 4KiB NOR to be read, we must finish doing what we know of
	 * the NOR mux in this space in order to continue.
	 */
#ifdef CONFIG_NOR_BOOT
	enable_norboot_pin_mux();
#endif
	/*
	 * Save the boot parameters passed from romcode.
	 * We cannot delay the saving further than this,
	 * to prevent overwrites.
	 */
#ifdef CONFIG_SPL_BUILD
	save_omap_boot_params();
#endif
	watchdog_disable();
	timer_init();
	set_uart_mux_conf();
	setup_clocks_for_console();
	uart_soft_reset();

#ifdef CONFIG_NOR_BOOT
	gd->baudrate = CONFIG_BAUDRATE;
	serial_init();
	gd->have_console = 1;
#elif defined(CONFIG_SPL_BUILD)
	gd = &gdata;
	preloader_console_init();
#endif

	prcm_init();
	set_mux_conf_regs();
	/* Enable RTC32K clock */
	rtc32k_enable();
	sdram_init();
}