Exemplos de get_fuserom_data em C++ (Cpp)

Exemplo n.º 1

Arquivo: magnetic_ak09911.c Projeto: GAXUSXX/G935FGaXusKernel2

int initialize_magnetic_sensor(struct ssp_data *data)
{
	int ret;

	ret = get_fuserom_data(data);
	if (ret < 0)
		pr_err("[SSP] %s - get_fuserom_data failed %d\n",
			__func__, ret);

	ret = set_pdc_matrix(data);
	if (ret < 0)
		pr_err("[SSP] %s - set_magnetic_pdc_matrix failed %d\n",
			__func__, ret);

	return ret < 0 ? ret : SUCCESS;
}

Exemplo n.º 2

Arquivo: ssp_dev.c Projeto: StanTRC/boeffla-kernel-cm-s5

int initialize_mcu(struct ssp_data *data)
{
	int iRet = 0;

	clean_pending_list(data);

	iRet = get_chipid(data);
	pr_info("[SSP] MCU device ID = %d, reading ID = %d\n", DEVICE_ID, iRet);
	if (iRet != DEVICE_ID) {
		if (iRet < 0) {
			pr_err("[SSP]: %s - MCU is not working : 0x%x\n",
				__func__, iRet);
		} else {
			pr_err("[SSP]: %s - MCU identification failed\n",
				__func__);
			iRet = -ENODEV;
		}
		goto out;
	}

	iRet = set_sensor_position(data);
	if (iRet < 0) {
		pr_err("[SSP]: %s - set_sensor_position failed\n", __func__);
		goto out;
	}

	iRet = get_fuserom_data(data);
	if (iRet < 0)
		pr_err("[SSP]: %s - get_fuserom_data failed\n", __func__);

	data->uSensorState = get_sensor_scanning_info(data);
	if (data->uSensorState == 0) {
		pr_err("[SSP]: %s - get_sensor_scanning_info failed\n",
			__func__);
		iRet = ERROR;
		goto out;
	}

	data->uCurFirmRev = get_firmware_rev(data);
	pr_info("[SSP] MCU Firm Rev : New = %8u\n",
		data->uCurFirmRev);

	iRet = ssp_send_cmd(data, MSG2SSP_AP_MCU_DUMP_CHECK, 0);
out:
	return iRet;
}

Exemplo n.º 3

Arquivo: ssp_dev.c Projeto: lssjbrolli/android_kernel_samsung_klimtlte

int initialize_mcu(struct ssp_data *data)
{
	int iRet = 0;

	iRet = get_chipid(data);
	pr_info("[SSP] MCU device ID = %d, reading ID = %d\n", DEVICE_ID, iRet);
	if (iRet != DEVICE_ID) {
		if (iRet < 0) {
			pr_err("[SSP]: %s - MCU is not working : 0x%x\n",
				__func__, iRet);
		} else {
			pr_err("[SSP]: %s - MCU identification failed\n",
				__func__);
			iRet = -ENODEV;
		}
		goto out;
	}

	iRet = set_sensor_position(data);
	if (iRet < 0) {
		pr_err("[SSP]: %s - set_sensor_position failed\n", __func__);
		goto out;
	}

	iRet = set_magnetic_static_matrix(data);
	if (iRet < 0)
		pr_err("[SSP] %s - set_magnetic_static_matrix failed\n", __func__);

	iRet = get_fuserom_data(data);
	if (iRet < 0)
		pr_err("[SSP]: %s - get_fuserom_data failed\n", __func__);

	data->uSensorState = get_sensor_scanning_info(data);
	if (data->uSensorState == 0) {
		pr_err("[SSP]: %s - get_sensor_scanning_info failed\n",
			__func__);
		iRet = ERROR;
		goto out;
	}

	iRet = SUCCESS;
out:
	return iRet;
}

Exemplo n.º 4

Arquivo: ssp_dev.c Projeto: ausdim/boeffla-kernel-jb-u8-s3

int initialize_mcu(struct ssp_data *data)
{
	int iRet = 0;

	iRet = get_chipid(data);
	pr_info("[SSP] MPU device ID = %d, reading ID = %d\n", DEVICE_ID, iRet);
	if (iRet != DEVICE_ID) {
		if (iRet < 0)
			pr_err("[SSP]: %s - i2c for reading chip id failed\n",
			       __func__);
		else {
			pr_err("[SSP]: %s - Device identification failed\n",
			       __func__);
			iRet = -ENODEV;
		}
		return iRet;
	}

	iRet = set_sensor_position(data);
	if (iRet < 0) {
		pr_err("[SSP]: %s - set_sensor_position failed\n", __func__);
		return iRet;
	}

	iRet = get_fuserom_data(data);
	if (iRet < 0) {
		pr_err("[SSP]: %s - get_fuserom_data failed\n", __func__);
		return iRet;
	}

	data->uAliveSensorDebug = get_sensor_scanning_info(data);
	if (data->uAliveSensorDebug == 0) {
		pr_err("[SSP]: %s - get_sensor_scanning_info failed\n",
			__func__);
		return FAIL;
	}

	return SUCCESS;
}