void AT91F_SpiInit(void)
{
/* Reset the SPI */
writel(AT91_SPI_SWRST, AT91_BASE_SPI + AT91_SPI_CR);
/* Configure SPI in Master Mode with No CS selected !!! */
writel(AT91_SPI_MSTR | AT91_SPI_MODFDIS | AT91_SPI_PCS,
AT91_BASE_SPI + AT91_SPI_MR);
/* Configure CS0 */
writel(AT91_SPI_NCPHA |
(AT91_SPI_DLYBS & DATAFLASH_TCSS) |
(AT91_SPI_DLYBCT & DATAFLASH_TCHS) |
((get_mck_clk_rate() / AT91_SPI_CLK) << 8),
AT91_BASE_SPI + AT91_SPI_CSR(0));
#ifdef CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1
/* Configure CS1 */
writel(AT91_SPI_NCPHA |
(AT91_SPI_DLYBS & DATAFLASH_TCSS) |
(AT91_SPI_DLYBCT & DATAFLASH_TCHS) |
((get_mck_clk_rate() / AT91_SPI_CLK) << 8),
AT91_BASE_SPI + AT91_SPI_CSR(1));
#endif
#ifdef CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS2
/* Configure CS2 */
writel(AT91_SPI_NCPHA |
(AT91_SPI_DLYBS & DATAFLASH_TCSS) |
(AT91_SPI_DLYBCT & DATAFLASH_TCHS) |
((get_mck_clk_rate() / AT91_SPI_CLK) << 8),
AT91_BASE_SPI + AT91_SPI_CSR(2));
#endif
#ifdef CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3
/* Configure CS3 */
writel(AT91_SPI_NCPHA |
(AT91_SPI_DLYBS & DATAFLASH_TCSS) |
(AT91_SPI_DLYBCT & DATAFLASH_TCHS) |
((get_mck_clk_rate() / AT91_SPI_CLK) << 8),
AT91_BASE_SPI + AT91_SPI_CSR(3));
#endif
/* SPI_Enable */
writel(AT91_SPI_SPIEN, AT91_BASE_SPI + AT91_SPI_CR);
while (!(readl(AT91_BASE_SPI + AT91_SPI_SR) & AT91_SPI_SPIENS));
/*
* Add tempo to get SPI in a safe state.
* Should not be needed for new silicon (Rev B)
*/
udelay(500000);
readl(AT91_BASE_SPI + AT91_SPI_SR);
readl(AT91_BASE_SPI + AT91_SPI_RDR);
}
int print_cpuinfo(void)
{
char buf[32];
printf("CPU: %s\n", AT91_CPU_NAME);
printf("Crystal frequency: %8s MHz\n",
strmhz(buf, get_main_clk_rate()));
printf("CPU clock : %8s MHz\n",
strmhz(buf, get_cpu_clk_rate()));
printf("Master clock : %8s MHz\n",
strmhz(buf, get_mck_clk_rate()));
return 0;
}
/* nothing really to do with interrupts, just starts up a counter. */
int timer_init(void)
{
at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
at91_pit_t *pit = (at91_pit_t *) AT91_PIT_BASE;
/*
* Enable PITC Clock
* The clock is already enabled for system controller in boot
*/
writel(1 << AT91_ID_SYS, &pmc->pcer);
/* Enable PITC */
writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
reset_timer_masked();
timer_freq = get_mck_clk_rate() >> 4;
return 0;
}
int misc_init_r(void)
{
char *str;
char buf[32];
/*
* Normally the processor clock has a divisor of 2.
* In some cases this this needs to be set to 4.
* Check the user has set environment mdiv to 4 to change the divisor.
*/
if ((str = getenv("mdiv")) && (strcmp(str, "4") == 0)) {
at91_sys_write(AT91_PMC_MCKR,
(at91_sys_read(AT91_PMC_MCKR) & ~AT91_PMC_MDIV) |
AT91SAM9_PMC_MDIV_4);
at91_clock_init(0);
serial_setbrg();
/* Notify the user that the clock is not default */
printf("Setting master clock to %s MHz\n",
strmhz(buf, get_mck_clk_rate()));
}
return 0;
}
int misc_init_r(void)
{
char *str;
char buf[32];
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
/*
* Normally the processor clock has a divisor of 2.
* In some cases this this needs to be set to 4.
* Check the user has set environment mdiv to 4 to change the divisor.
*/
if ((str = getenv("mdiv")) && (strcmp(str, "4") == 0)) {
writel((readl(&pmc->mckr) & ~AT91_PMC_MDIV) |
AT91SAM9_PMC_MDIV_4, &pmc->mckr);
at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
serial_setbrg();
/* Notify the user that the clock is not default */
printf("Setting master clock to %s MHz\n",
strmhz(buf, get_mck_clk_rate()));
}
return 0;
}
