static int __dwc3_stop_host(struct usb_hcd *hcd)
{
int count = 0;
u32 data;
struct xhci_hcd *xhci;
struct usb_hcd *xhci_shared_hcd;
if (!hcd)
return -EINVAL;
if (dwc3_xhci.comp_test_enable) {
dev_dbg(hcd->self.controller,
"%s() - Now is in comp test mode", __func__);
return 0;
}
xhci = hcd_to_xhci(hcd);
pm_runtime_get_sync(hcd->self.controller);
/* Disable hibernation mode for D0i3cold. */
data = readl(hcd->regs + GCTL);
data &= ~GCTL_GBL_HIBERNATION_EN;
writel(data, hcd->regs + GCTL);
/* When plug out micro A cable, there will be two flows be executed.
* The first one is xHCI controller get disconnect event. The
* second one is PMIC get ID change event. During these events
* handling, they both try to call usb_disconnect. Then met some
* conflicts and cause kernel panic.
* So treat disconnect event as first priority, handle the ID change
* event until disconnect event handled done.*/
while (if_usb_devices_connected(xhci)) {
msleep(20);
if (count++ > WAIT_DISC_EVENT_COMPLETE_TIMEOUT)
break;
};
dwc3_xhci_driver.shutdown = NULL;
if (xhci->shared_hcd) {
xhci_shared_hcd = xhci->shared_hcd;
usb_remove_hcd(xhci_shared_hcd);
usb_put_hcd(xhci_shared_hcd);
}
usb_remove_hcd(hcd);
dwc3_xhci.xhci = NULL;
kfree(xhci);
*((struct xhci_hcd **) hcd->hcd_priv) = NULL;
dwc_xhci_enable_phy_suspend(hcd, false);
pm_runtime_put(hcd->self.controller);
device_remove_file(hcd->self.controller, &dev_attr_pm_get);
return 0;
}
/* dwc_hcd_suspend_common and dwc_hcd_resume_common are refer to
* suspend_common and resume_common in usb core.
* Because the usb core function just support PCI device.
* So re-write them in here to support platform devices.
*/
static int dwc_hcd_suspend_common(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int retval = 0;
u32 data = 0;
if (!xhci) {
dev_dbg(dev, "%s: host already stop!\n", __func__);
return 0;
}
/* Root hub suspend should have stopped all downstream traffic,
* and all bus master traffic. And done so for both the interface
* and the stub usb_device (which we check here). But maybe it
* didn't; writing sysfs power/state files ignores such rules...
*/
if (HCD_RH_RUNNING(hcd)) {
dev_warn(dev, "Root hub is not suspended\n");
return -EBUSY;
}
if (hcd->shared_hcd) {
hcd = hcd->shared_hcd;
if (HCD_RH_RUNNING(hcd)) {
dev_warn(dev, "Secondary root hub is not suspended\n");
return -EBUSY;
}
}
if (!HCD_DEAD(hcd)) {
/* Optimization: Don't suspend if a root-hub wakeup is
* pending and it would cause the HCD to wake up anyway.
*/
if (HCD_WAKEUP_PENDING(hcd))
return -EBUSY;
if (hcd->shared_hcd &&
HCD_WAKEUP_PENDING(hcd->shared_hcd))
return -EBUSY;
if (hcd->state != HC_STATE_SUSPENDED ||
xhci->shared_hcd->state != HC_STATE_SUSPENDED)
retval = -EINVAL;
if (!retval) {
/* The auto-resume is diabled by default. Need enable it
* if there have valid connection. To ensure that when
* device resumes, host does resume reflect within
* 900 usec as in USB spec.
*/
if (if_usb_devices_connected(xhci) == 1)
dwc_xhci_enable_phy_auto_resume(
xhci->main_hcd, true);
/* Ensure that suspend enable are set for
* USB2 and USB3 PHY
*/
dwc_xhci_enable_phy_suspend(hcd, true);
data = readl(hcd->regs + GCTL);
data |= GCTL_GBL_HIBERNATION_EN;
writel(data, hcd->regs + GCTL);
dev_dbg(hcd->self.controller, "set xhci hibernation enable!\n");
retval = xhci_suspend(xhci);
}
/* Check again in case wakeup raced with pci_suspend */
if ((retval == 0 && HCD_WAKEUP_PENDING(hcd)) ||
(retval == 0 && hcd->shared_hcd &&
HCD_WAKEUP_PENDING(hcd->shared_hcd))) {
xhci_resume(xhci, false);
retval = -EBUSY;
}
if (retval)
return retval;
}
synchronize_irq(dwc3_xhci.otg_irqnum);
return retval;
}
