void init(void)
{
uint8_t i;
drv_pwm_config_t pwm_params;
bool sensorsOK = false;
initPrintfSupport();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
#ifdef STM32F303
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(masterConfig.emf_avoidance);
#endif
#ifdef NAZE
detectHardwareRevision();
#endif
systemInit();
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (masterConfig.rxConfig.serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(&masterConfig.rxConfig);
break;
}
}
#endif
delay(100);
timerInit(); // timer must be initialized before any channel is allocated
ledInit();
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.gpioMode = Mode_Out_OD,
.gpioPin = BEEP_PIN,
.gpioPort = BEEP_GPIO,
.gpioPeripheral = BEEP_PERIPHERAL,
.isInverted = false
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.gpioMode = Mode_Out_PP;
beeperConfig.isInverted = true;
}
#endif
beeperInit(&beeperConfig);
#endif
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_SPI
spiInit(SPI1);
spiInit(SPI2);
#endif
#ifdef NAZE
updateHardwareRevision();
#endif
#ifdef USE_I2C
#ifdef NAZE
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
}
#else
// Configure the rest of the stuff
i2cInit(I2C_DEVICE);
#endif
#endif
#if !defined(SPARKY)
drv_adc_config_t adc_params;
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment(&masterConfig.boardAlignment);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit(&masterConfig.rxConfig);
}
#endif
// We have these sensors; SENSORS_SET defined in board.h depending on hardware platform
sensorsSet(SENSORS_SET);
// drop out any sensors that don't seem to work, init all the others. halt if gyro is dead.
sensorsOK = sensorsAutodetect(&masterConfig.sensorAlignmentConfig, masterConfig.gyro_lpf, masterConfig.acc_hardware, masterConfig.mag_hardware, currentProfile->mag_declination);
// if gyro was not detected due to whatever reason, we give up now.
if (!sensorsOK)
failureMode(3);
LED1_ON;
LED0_OFF;
for (i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
imuInit();
mixerInit(masterConfig.mixerMode, masterConfig.customMixer);
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
serialInit(&masterConfig.serialConfig);
memset(&pwm_params, 0, sizeof(pwm_params));
// when using airplane/wing mixer, servo/motor outputs are remapped
if (masterConfig.mixerMode == MIXER_AIRPLANE || masterConfig.mixerMode == MIXER_FLYING_WING)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(SERIAL_PORT_USART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_USART2);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = feature(FEATURE_CURRENT_METER);
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useOneshot = feature(FEATURE_ONESHOT125);
pwm_params.useServos = isMixerUsingServos();
pwm_params.extraServos = currentProfile->gimbalConfig.gimbal_flags & GIMBAL_FORWARDAUX;
pwm_params.motorPwmRate = masterConfig.motor_pwm_rate;
pwm_params.servoPwmRate = masterConfig.servo_pwm_rate;
pwm_params.idlePulse = PULSE_1MS; // standard PWM for brushless ESC (default, overridden below)
if (feature(FEATURE_3D))
pwm_params.idlePulse = masterConfig.flight3DConfig.neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
pwm_params.servoCenterPulse = masterConfig.rxConfig.midrc;
pwmRxInit(masterConfig.inputFilteringMode);
pwmOutputConfiguration_t *pwmOutputConfiguration = pwmInit(&pwm_params);
mixerUsePWMOutputConfiguration(pwmOutputConfiguration);
failsafe = failsafeInit(&masterConfig.rxConfig);
beepcodeInit(failsafe);
rxInit(&masterConfig.rxConfig, failsafe);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit(
&masterConfig.serialConfig,
&masterConfig.gpsConfig
);
navigationInit(
¤tProfile->gpsProfile,
¤tProfile->pidProfile
);
}
#endif
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
Sonar_init();
}
#endif
#ifdef LED_STRIP
ledStripInit(masterConfig.ledConfigs, masterConfig.colors, failsafe);
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY))
initTelemetry();
#endif
previousTime = micros();
if (masterConfig.mixerMode == MIXER_GIMBAL) {
accSetCalibrationCycles(CALIBRATING_ACC_CYCLES);
}
gyroSetCalibrationCycles(CALIBRATING_GYRO_CYCLES);
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
// Check battery type/voltage
if (feature(FEATURE_VBAT))
batteryInit(&masterConfig.batteryConfig);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
#ifdef USE_OLED_GPS_DEBUG_PAGE_ONLY
displayShowFixedPage(PAGE_GPS);
#else
displayEnablePageCycling();
#endif
}
#endif
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialTotalBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
int main(void) {
init();
while (1) {
loop();
processLoopback();
}
}
// this code is executed at each loop and won't interfere with control loop if it lasts less than 650 microseconds
void annexCode(void)
{
static uint32_t calibratedAccTime;
uint16_t tmp, tmp2;
static uint8_t buzzerFreq; //delay between buzzer ring
static uint8_t vbatTimer = 0;
uint8_t axis, prop1, prop2;
static uint8_t ind = 0;
uint16_t vbatRaw = 0;
static uint16_t vbatRawArray[8];
uint8_t i;
// PITCH & ROLL only dynamic PID adjustemnt, depending on throttle value
if (rcData[THROTTLE] < BREAKPOINT) {
prop2 = 100;
} else {
if (rcData[THROTTLE] < 2000) {
prop2 = 100 - (uint16_t) cfg.dynThrPID * (rcData[THROTTLE] - BREAKPOINT) / (2000 - BREAKPOINT);
} else {
prop2 = 100 - cfg.dynThrPID;
}
}
for (axis = 0; axis < 3; axis++) {
tmp = min(abs(rcData[axis] - cfg.midrc), 500);
if (axis != 2) { // ROLL & PITCH
if (cfg.deadband) {
if (tmp > cfg.deadband) {
tmp -= cfg.deadband;
} else {
tmp = 0;
}
}
tmp2 = tmp / 100;
rcCommand[axis] = lookupPitchRollRC[tmp2] + (tmp - tmp2 * 100) * (lookupPitchRollRC[tmp2 + 1] - lookupPitchRollRC[tmp2]) / 100;
prop1 = 100 - (uint16_t) cfg.rollPitchRate * tmp / 500;
prop1 = (uint16_t) prop1 *prop2 / 100;
} else { // YAW
if (cfg.yawdeadband) {
if (tmp > cfg.yawdeadband) {
tmp -= cfg.yawdeadband;
} else {
tmp = 0;
}
}
rcCommand[axis] = tmp;
prop1 = 100 - (uint16_t) cfg.yawRate * tmp / 500;
}
dynP8[axis] = (uint16_t) cfg.P8[axis] * prop1 / 100;
dynD8[axis] = (uint16_t) cfg.D8[axis] * prop1 / 100;
if (rcData[axis] < cfg.midrc)
rcCommand[axis] = -rcCommand[axis];
}
tmp = constrain(rcData[THROTTLE], cfg.mincheck, 2000);
tmp = (uint32_t) (tmp - cfg.mincheck) * 1000 / (2000 - cfg.mincheck); // [MINCHECK;2000] -> [0;1000]
tmp2 = tmp / 100;
rcCommand[THROTTLE] = lookupThrottleRC[tmp2] + (tmp - tmp2 * 100) * (lookupThrottleRC[tmp2 + 1] - lookupThrottleRC[tmp2]) / 100; // [0;1000] -> expo -> [MINTHROTTLE;MAXTHROTTLE]
if(f.HEADFREE_MODE) {
float radDiff = (heading - headFreeModeHold) * M_PI / 180.0f;
float cosDiff = cosf(radDiff);
float sinDiff = sinf(radDiff);
int16_t rcCommand_PITCH = rcCommand[PITCH] * cosDiff + rcCommand[ROLL] * sinDiff;
rcCommand[ROLL] = rcCommand[ROLL] * cosDiff - rcCommand[PITCH] * sinDiff;
rcCommand[PITCH] = rcCommand_PITCH;
}
if (feature(FEATURE_VBAT)) {
if (!(++vbatTimer % VBATFREQ)) {
vbatRawArray[(ind++) % 8] = adcGetBattery();
for (i = 0; i < 8; i++)
vbatRaw += vbatRawArray[i];
vbat = batteryAdcToVoltage(vbatRaw / 8);
}
if ((vbat > batteryWarningVoltage) || (vbat < cfg.vbatmincellvoltage)) { // VBAT ok, buzzer off
buzzerFreq = 0;
} else
buzzerFreq = 4; // low battery
}
buzzer(buzzerFreq); // external buzzer routine that handles buzzer events globally now
if ((calibratingA > 0 && sensors(SENSOR_ACC)) || (calibratingG > 0)) { // Calibration phasis
LED0_TOGGLE;
} else {
if (f.ACC_CALIBRATED)
LED0_OFF;
if (f.ARMED)
LED0_ON;
// This will switch to/from 9600 or 115200 baud depending on state. Of course, it should only do it on changes.
if (feature(FEATURE_TELEMETRY))
initTelemetry(f.ARMED);
}
#ifdef LEDRING
if (feature(FEATURE_LED_RING)) {
static uint32_t LEDTime;
if ((int32_t)(currentTime - LEDTime) >= 0) {
LEDTime = currentTime + 50000;
ledringState();
}
}
#endif
if ((int32_t)(currentTime - calibratedAccTime) >= 0) {
if (!f.SMALL_ANGLES_25) {
f.ACC_CALIBRATED = 0; // the multi uses ACC and is not calibrated or is too much inclinated
LED0_TOGGLE;
calibratedAccTime = currentTime + 500000;
} else {
f.ACC_CALIBRATED = 1;
}
}
serialCom();
if (sensors(SENSOR_GPS)) {
static uint32_t GPSLEDTime;
if ((int32_t)(currentTime - GPSLEDTime) >= 0 && (GPS_numSat >= 5)) {
GPSLEDTime = currentTime + 150000;
LED1_TOGGLE;
}
}
// Read out gyro temperature. can use it for something somewhere. maybe get MCU temperature instead? lots of fun possibilities.
if (gyro.temperature)
gyro.temperature(&telemTemperature1);
else {
// TODO MCU temp
}
}
int main(void)
{
uint8_t i;
drv_pwm_config_t pwm_params;
drv_adc_config_t adc_params;
bool sensorsOK = false;
#ifdef SOFTSERIAL_LOOPBACK
serialPort_t* loopbackPort1 = NULL;
serialPort_t* loopbackPort2 = NULL;
#endif
initEEPROM();
checkFirstTime(false);
readEEPROM();
systemInit(mcfg.emf_avoidance);
#ifdef USE_LAME_PRINTF
init_printf(NULL, _putc);
#endif
activateConfig();
// configure power ADC
if (mcfg.power_adc_channel > 0 && (mcfg.power_adc_channel == 1 || mcfg.power_adc_channel == 9))
adc_params.powerAdcChannel = mcfg.power_adc_channel;
else {
adc_params.powerAdcChannel = 0;
mcfg.power_adc_channel = 0;
}
adcInit(&adc_params);
// Check battery type/voltage
if (feature(FEATURE_VBAT))
batteryInit();
initBoardAlignment();
// We have these sensors; SENSORS_SET defined in board.h depending on hardware platform
sensorsSet(SENSORS_SET);
// drop out any sensors that don't seem to work, init all the others. halt if gyro is dead.
sensorsOK = sensorsAutodetect();
// production debug output
#ifdef PROD_DEBUG
productionDebug();
#endif
// if gyro was not detected due to whatever reason, we give up now.
if (!sensorsOK)
failureMode(3);
LED1_ON;
LED0_OFF;
for (i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
imuInit(); // Mag is initialized inside imuInit
mixerInit(); // this will set core.useServo var depending on mixer type
serialInit(mcfg.serial_baudrate);
// when using airplane/wing mixer, servo/motor outputs are remapped
if (mcfg.mixerConfiguration == MULTITYPE_AIRPLANE || mcfg.mixerConfiguration == MULTITYPE_FLYING_WING)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
pwm_params.useUART = feature(FEATURE_GPS) || feature(FEATURE_SERIALRX); // spektrum/sbus support uses UART too
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.usePPM = feature(FEATURE_PPM);
pwm_params.enableInput = !feature(FEATURE_SERIALRX); // disable inputs if using spektrum
pwm_params.useServos = core.useServo;
pwm_params.extraServos = cfg.gimbal_flags & GIMBAL_FORWARDAUX;
pwm_params.motorPwmRate = mcfg.motor_pwm_rate;
pwm_params.servoPwmRate = mcfg.servo_pwm_rate;
pwm_params.idlePulse = PULSE_1MS; // standard PWM for brushless ESC (default, overridden below)
if (feature(FEATURE_3D))
pwm_params.idlePulse = mcfg.neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
pwm_params.servoCenterPulse = mcfg.midrc;
pwm_params.failsafeThreshold = cfg.failsafe_detect_threshold;
switch (mcfg.power_adc_channel) {
case 1:
pwm_params.adcChannel = PWM2;
break;
case 9:
pwm_params.adcChannel = PWM8;
break;
default:
pwm_params.adcChannel = 0;
break;
}
pwmInit(&pwm_params);
core.numServos = pwm_params.numServos;
// configure PWM/CPPM read function and max number of channels. spektrum or sbus below will override both of these, if enabled
for (i = 0; i < RC_CHANS; i++)
rcData[i] = 1502;
rcReadRawFunc = pwmReadRawRC;
core.numRCChannels = MAX_INPUTS;
if (feature(FEATURE_SERIALRX)) {
switch (mcfg.serialrx_type) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
spektrumInit(&rcReadRawFunc);
break;
case SERIALRX_SBUS:
sbusInit(&rcReadRawFunc);
break;
case SERIALRX_SUMD:
sumdInit(&rcReadRawFunc);
break;
case SERIALRX_MSP:
mspInit(&rcReadRawFunc);
break;
}
} else { // spektrum and GPS are mutually exclusive
// Optional GPS - available in both PPM and PWM input mode, in PWM input, reduces number of available channels by 2.
// gpsInit will return if FEATURE_GPS is not enabled.
gpsInit(mcfg.gps_baudrate);
}
#ifdef SONAR
// sonar stuff only works with PPM
if (feature(FEATURE_PPM)) {
if (feature(FEATURE_SONAR))
Sonar_init();
}
#endif
if (feature(FEATURE_SOFTSERIAL)) {
//mcfg.softserial_baudrate = 19200; // Uncomment to override config value
setupSoftSerialPrimary(mcfg.softserial_baudrate, mcfg.softserial_1_inverted);
setupSoftSerialSecondary(mcfg.softserial_2_inverted);
#ifdef SOFTSERIAL_LOOPBACK
loopbackPort1 = (serialPort_t*)&(softSerialPorts[0]);
serialPrint(loopbackPort1, "SOFTSERIAL 1 - LOOPBACK ENABLED\r\n");
loopbackPort2 = (serialPort_t*)&(softSerialPorts[1]);
serialPrint(loopbackPort2, "SOFTSERIAL 2 - LOOPBACK ENABLED\r\n");
#endif
//core.mainport = (serialPort_t*)&(softSerialPorts[0]); // Uncomment to switch the main port to use softserial.
}
if (feature(FEATURE_TELEMETRY))
initTelemetry();
previousTime = micros();
if (mcfg.mixerConfiguration == MULTITYPE_GIMBAL)
calibratingA = CALIBRATING_ACC_CYCLES;
calibratingG = CALIBRATING_GYRO_CYCLES;
calibratingB = CALIBRATING_BARO_CYCLES; // 10 seconds init_delay + 200 * 25 ms = 15 seconds before ground pressure settles
f.SMALL_ANGLE = 1;
// loopy
while (1) {
loop();
#ifdef SOFTSERIAL_LOOPBACK
if (loopbackPort1) {
while (serialTotalBytesWaiting(loopbackPort1)) {
uint8_t b = serialRead(loopbackPort1);
serialWrite(loopbackPort1, b);
//serialWrite(core.mainport, 0x01);
//serialWrite(core.mainport, b);
};
}
if (loopbackPort2) {
while (serialTotalBytesWaiting(loopbackPort2)) {
#ifndef OLIMEXINO // PB0/D27 and PB1/D28 internally connected so this would result in a continuous stream of data
serialRead(loopbackPort2);
#else
uint8_t b = serialRead(loopbackPort2);
serialWrite(loopbackPort2, b);
//serialWrite(core.mainport, 0x02);
//serialWrite(core.mainport, b);
#endif // OLIMEXINO
};
}
#endif
}
}
int main(void)
{
uint8_t i;
drv_pwm_config_t pwm_params;
drv_adc_config_t adc_params;
serialPort_t* loopbackPort = NULL;
systemInit();
#ifdef USE_LAME_PRINTF
init_printf(NULL, _putc);
#endif
checkFirstTime(false);
readEEPROM();
// configure power ADC
if (mcfg.power_adc_channel > 0 && (mcfg.power_adc_channel == 1 || mcfg.power_adc_channel == 9))
adc_params.powerAdcChannel = mcfg.power_adc_channel;
else {
adc_params.powerAdcChannel = 0;
mcfg.power_adc_channel = 0;
}
adcInit(&adc_params);
initBoardAlignment();
// We have these sensors; SENSORS_SET defined in board.h depending on hardware platform
sensorsSet(SENSORS_SET);
mixerInit(); // this will set core.useServo var depending on mixer type
// when using airplane/wing mixer, servo/motor outputs are remapped
if (mcfg.mixerConfiguration == MULTITYPE_AIRPLANE || mcfg.mixerConfiguration == MULTITYPE_FLYING_WING)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
//pwm_params.useUART = feature(FEATURE_GPS) || feature(FEATURE_SERIALRX); // spektrum/sbus support uses UART too
pwm_params.useUART = feature(FEATURE_GPS);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.usePPM = feature(FEATURE_PPM);
pwm_params.enableInput = !feature(FEATURE_SERIALRX); // disable inputs if using spektrum
pwm_params.useServos = core.useServo;
pwm_params.extraServos = cfg.gimbal_flags & GIMBAL_FORWARDAUX;
pwm_params.motorPwmRate = mcfg.motor_pwm_rate;
pwm_params.servoPwmRate = mcfg.servo_pwm_rate;
pwm_params.idlePulse = PULSE_1MS; // standard PWM for brushless ESC (default, overridden below)
if (feature(FEATURE_3D))
pwm_params.idlePulse = mcfg.neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
pwm_params.servoCenterPulse = mcfg.midrc;
pwm_params.failsafeThreshold = cfg.failsafe_detect_threshold;
switch (mcfg.power_adc_channel) {
case 1:
pwm_params.adcChannel = PWM2;
break;
case 9:
pwm_params.adcChannel = PWM8;
break;
default:
pwm_params.adcChannel = 0;
break;
}
pwmInit(&pwm_params);
// configure PWM/CPPM read function and max number of channels. spektrum or sbus below will override both of these, if enabled
for (i = 0; i < RC_CHANS; i++)
rcData[i] = 1502;
rcReadRawFunc = pwmReadRawRC;
core.numRCChannels = MAX_INPUTS;
if (feature(FEATURE_SERIALRX)) {
switch (mcfg.serialrx_type) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
spektrumInit(&rcReadRawFunc);
break;
case SERIALRX_SBUS:
sbusInit(&rcReadRawFunc);
break;
case SERIALRX_SUMD:
sumdInit(&rcReadRawFunc);
break;
#if defined(SKYROVER)
case SERIALRX_HEXAIRBOT:
hexairbotInit(&rcReadRawFunc);
break;
#endif
}
} else { // spektrum and GPS are mutually exclusive
// Optional GPS - available in both PPM and PWM input mode, in PWM input, reduces number of available channels by 2.
// gpsInit will return if FEATURE_GPS is not enabled.
// Sanity check below - protocols other than NMEA do not support baud rate autodetection
if (mcfg.gps_type > 0 && mcfg.gps_baudrate < 0)
mcfg.gps_baudrate = 0;
gpsInit(mcfg.gps_baudrate);
}
#ifdef SONAR
// sonar stuff only works with PPM
if (feature(FEATURE_PPM)) {
if (feature(FEATURE_SONAR))
Sonar_init();
}
#endif
LED1_ON;
LED0_OFF;
for (i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
serialInit(mcfg.serial_baudrate);
DEBUG_PRINT("Booting..\r\n");
// drop out any sensors that don't seem to work, init all the others. halt if gyro is dead.
sensorsAutodetect();
imuInit(); // Mag is initialized inside imuInit
// Check battery type/voltage
if (feature(FEATURE_VBAT))
batteryInit();
if (feature(FEATURE_SOFTSERIAL)) {
setupSoftSerial1(mcfg.softserial_baudrate, mcfg.softserial_inverted);
#ifdef SOFTSERIAL_LOOPBACK
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
serialPrint(loopbackPort, "LOOPBACK ENABLED\r\n");
#endif
}
if (feature(FEATURE_TELEMETRY))
initTelemetry();
previousTime = micros();
if (mcfg.mixerConfiguration == MULTITYPE_GIMBAL)
calibratingA = CALIBRATING_ACC_CYCLES;
calibratingG = CALIBRATING_GYRO_CYCLES;
calibratingB = CALIBRATING_BARO_CYCLES; // 10 seconds init_delay + 200 * 25 ms = 15 seconds before ground pressure settles
f.SMALL_ANGLES_25 = 1;
DEBUG_PRINT("Start\r\n");
// loopy
while (1) {
loop();
#ifdef SOFTSERIAL_LOOPBACK
if (loopbackPort) {
while (serialTotalBytesWaiting(loopbackPort)) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
//serialWrite(core.mainport, b);
};
}
#endif
}
}
