static int jmicron_probe(struct sdhci_pci_chip *chip)
{
int ret;
if (chip->pdev->revision == 0) {
chip->quirks |= SDHCI_QUIRK_32BIT_DMA_ADDR |
SDHCI_QUIRK_32BIT_DMA_SIZE |
SDHCI_QUIRK_32BIT_ADMA_SIZE |
SDHCI_QUIRK_RESET_AFTER_REQUEST |
SDHCI_QUIRK_BROKEN_SMALL_PIO |
SDHCI_QUIRK_FORCE_HIGHSPEED;
}
/*
* JMicron chips can have two interfaces to the same hardware
* in order to work around limitations in Microsoft's driver.
* We need to make sure we only bind to one of them.
*
* This code assumes two things:
*
* 1. The PCI code adds subfunctions in order.
*
* 2. The MMC interface has a lower subfunction number
* than the SD interface.
*/
if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_SD) {
struct pci_dev *sd_dev;
sd_dev = NULL;
while ((sd_dev = pci_get_device(PCI_VENDOR_ID_JMICRON,
PCI_DEVICE_ID_JMICRON_JMB38X_MMC, sd_dev)) != NULL) {
if ((PCI_SLOT(chip->pdev->devfn) ==
PCI_SLOT(sd_dev->devfn)) &&
(chip->pdev->bus == sd_dev->bus))
break;
}
if (sd_dev) {
pci_dev_put(sd_dev);
dev_info(&chip->pdev->dev, "Refusing to bind to "
"secondary interface.\n");
return -ENODEV;
}
}
/*
* JMicron chips need a bit of a nudge to enable the power
* output pins.
*/
ret = jmicron_pmos(chip, 1);
if (ret) {
dev_err(&chip->pdev->dev, "Failure enabling card power\n");
return ret;
}
return 0;
}
static int jmicron_probe(struct sdhci_pci_chip *chip)
{
int ret;
u16 mmcdev = 0;
if (chip->pdev->revision == 0) {
chip->quirks |= SDHCI_QUIRK_32BIT_DMA_ADDR |
SDHCI_QUIRK_32BIT_DMA_SIZE |
SDHCI_QUIRK_32BIT_ADMA_SIZE |
SDHCI_QUIRK_RESET_AFTER_REQUEST |
SDHCI_QUIRK_BROKEN_SMALL_PIO;
}
if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_SD)
mmcdev = PCI_DEVICE_ID_JMICRON_JMB38X_MMC;
else if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB388_SD)
mmcdev = PCI_DEVICE_ID_JMICRON_JMB388_ESD;
if (mmcdev) {
struct pci_dev *sd_dev;
sd_dev = NULL;
while ((sd_dev = pci_get_device(PCI_VENDOR_ID_JMICRON,
mmcdev, sd_dev)) != NULL) {
if ((PCI_SLOT(chip->pdev->devfn) ==
PCI_SLOT(sd_dev->devfn)) &&
(chip->pdev->bus == sd_dev->bus))
break;
}
if (sd_dev) {
pci_dev_put(sd_dev);
dev_info(&chip->pdev->dev, "Refusing to bind to "
"secondary interface.\n");
return -ENODEV;
}
}
ret = jmicron_pmos(chip, 1);
if (ret) {
dev_err(&chip->pdev->dev, "Failure enabling card power\n");
return ret;
}
if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB388_SD ||
chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB388_ESD)
chip->quirks |= SDHCI_QUIRK_UNSTABLE_RO_DETECT;
return 0;
}