void MyMIWI_Init(void) {
// Configure Pins for MRF24J40MB
mPORTESetBits(RST_MIWI);
mPORTESetPinsDigitalOut(RST_MIWI);
mPORTBSetBits(MIWI_WAKE);
mPORTBSetPinsDigitalOut(MIWI_WAKE);
// Configure the INT3 controller for MIWI
// Set RD10/INT3 as input
mPORTDSetPinsDigitalIn(BIT_10);
// Clear corresponding bits in INTCON for falling edge trigger
INTCONCLR = _INTCON_INT3EP_MASK;
// Set up interrupt prioirty and sub-priority
INTSetVectorPriority(INT_EXTERNAL_3_VECTOR, My_INT_EXTERNAL_3_PRIORITY);
INTSetVectorSubPriority(INT_EXTERNAL_3_VECTOR, My_INT_EXTERNAL_3_SUB_PRIORITY);
// Clear the interrupt flags
INTClearFlag(INT_INT3);
// Enable INT3
INTEnable(INT_INT3, INT_ENABLED);
// WARNING : Change in file MRF24J40.c in Microchip Application Library
// the line : void __ISR(_EXTERNAL_1_VECTOR, ipl4) _INT1Interrupt(void)
// by : void __ISR(_EXTERNAL_3_VECTOR, ipl4) _INT3Interrupt(void)
}
void MyCyclone_Init(void)
{
// Configure Reset Pin = GPIO_2[10] = RD7
mPORTDClearBits(RST_FPGA);
mPORTDSetPinsDigitalOut(RST_FPGA);
// Do a Reset
mPORTDSetBits(RST_FPGA);
mPORTDClearBits(RST_FPGA);
// Do Interrupts Initialization
// Set RD8/INT1 and RD9/INT2 as inputs
mPORTDSetPinsDigitalIn(BIT_8 | BIT_9);
// Clear corresponding bits in INTCON for falling edge trigger
INTCONCLR = _INTCON_INT1EP_MASK | _INTCON_INT2EP_MASK;
// Set up interrupt prioirty and sub-priority
INTSetVectorPriority(INT_EXTERNAL_1_VECTOR, My_INT_EXTERNAL_1_PRIORITY);
INTSetVectorSubPriority(INT_EXTERNAL_1_VECTOR, My_INT_EXTERNAL_1_SUB_PRIORITY);
INTSetVectorPriority(INT_EXTERNAL_2_VECTOR, My_INT_EXTERNAL_2_PRIORITY);
INTSetVectorSubPriority(INT_EXTERNAL_2_VECTOR, My_INT_EXTERNAL_2_SUB_PRIORITY);
// Clear the interrupt flags
INTClearFlag(INT_INT1);
INTClearFlag(INT_INT2);
// Enable INT1 & INT2
INTEnable(INT_INT1, INT_ENABLED);
INTEnable(INT_INT2, INT_ENABLED);
// Enable KEY0 and KEY1 interrupts and IOs of the MyExpansionBoard_IO_v2
MyCyclone_Write(CYCLONE_CONFIG,CYCLONE_ENABLE_INT_KEY0 | CYCLONE_ENABLE_INT_KEY1 | CYCLONE_ENABLE_IO_AB | CYCLONE_ENABLE_IO_CD);
}
int main()
{
i=0;
lcdini();
DDPCON=0x0000;
mPORTDSetPinsDigitalIn(BIT_7|BIT_13|BIT_6); //Set Portd pins DigitalIn
mPORTASetPinsDigitalOut(BIT_0|BIT_1|BIT_2|BIT_3|BIT_4|BIT_5|BIT_6);
mPORTAClearBits(BIT_0|BIT_1|BIT_2|BIT_3|BIT_4|BIT_5|BIT_6);
mPORTASetPinsDigitalIn(BIT_7);
char x;
while(1)
{
switch(i) //Switch case to select function
{
case 0:
mode();
break;
case 1:
batteryv();
break;
case 2:
temps();
break;
}
if(i==3)
{
lcdcmd(0x01);
break;
}
}
}
//Function to initialize buttons BTN1, BTN2, and BTN3
void initButtons()
{
speeds = 1;
int x;
for(x = 0; x<4; x++)
{
samples[x] = 0x00;
waitingFor[x] = 1;
}
mPORTGSetPinsDigitalIn(BIT_6 | BIT_7);
mPORTDSetPinsDigitalIn(BIT_13 );
mPORTFSetPinsDigitalIn(BIT_4 | BIT_13);
}
void InitializeIO(void)
{
//Initializing CSN and CE pins as output
mPORTFSetPinsDigitalOut(BIT_0 | BIT_1);
mPORTFClearBits(BIT_0 | BIT_1);
//Initializing IRQ pin as input
mPORTDSetPinsDigitalIn(BIT_13);
mPORTDClearBits(BIT_13);
//Setting CSN bit active
LATFbits.LATF1 = 1;
//Initializing LEDs
mPORTDSetPinsDigitalOut(BIT_1 | BIT_2);
mPORTDClearBits(BIT_1 | BIT_2);
//Initializing MOSI/SDO1 and SCK as output
mPORTDSetPinsDigitalOut(BIT_10);
mPORTDSetPinsDigitalOut(BIT_0);
//Initializing MISO/SDI1 as input
mPORTCSetPinsDigitalIn(BIT_4);
}
void setupHardware()
{
SYSTEMConfig(SYS_CLOCK, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
mPORTDSetPinsDigitalOut(BIT_1); //yellow LED
mPORTGSetPinsDigitalOut(BIT_6); //green LED
//A1 PIR Input (CN4 module, RB2)
//A2 STB current consumption (AN3)
//D0 IR Output
mPORTDSetPinsDigitalOut(BIT_3); //D1 STB IRF control
mPORTDSetPinsDigitalIn(BIT_4); //D2 BUT OTG
mPORTDSetPinsDigitalOut(BIT_5); //D3 SHD RED LED Command OFF acqusition notificaiton
mPORTDSetPinsDigitalOut(BIT_6); //D4 SHD GREEN LED Command ON acqusition notificaiton
//D5 IR input (RD7)
//D6 SHD BUT1
//D7 SHD BUT2
mPORTBSetPinsDigitalOut(BIT_14); //D9 monitor relay control
DDPCONbits.JTAGEN = 0;
initLEDs();
initUART();
initADC();
setupCNModuleAnd_IR_PIR_Input();
//setupCNModuleAndPIRInput();
configureRTC();
setupIRTransmit();
switchMonitorOff();
switchSTBOff();
INTConfigureSystem(INT_SYSTEM_CONFIG_MULT_VECTOR);
INTEnableInterrupts();
T2CONbits.ON = 1;
}
void setupCNModuleAnd_IR_PIR_Input()
{
//T2 used to sample IR Input signals
setupTimer2();
//IR INPUT
mPORTDSetPinsDigitalIn(BIT_7); //D5 IR Input (CN16 module, RD7)
//PIR input
mPORTBSetPinsDigitalIn(BIT_2); //A1 PIR Input (CN4 module, RB2)
// setup the change notice options
//(ensure that CN continues working in sleep mode)
mCNOpen(CN_OFF | CN_IDLE_CON, CN16_ENABLE | CN4_ENABLE, CN16_PULLUP_ENABLE | CN4_PULLUP_ENABLE);
// read port(s) to clear mismatch
mPORTDReadBits(BIT_7);
mPORTBReadBits(BIT_2);
mPORTBReadBits(BIT_4);
// configure interrupts and clear change notice interrupt flag
ConfigIntCN(CHANGE_INT_ON | CHANGE_INT_PRI_3);
mCNClearIntFlag(); // Clear interrupt flag
}
/****************************************************************************
Function:
static void InitializeBoard(void)
Description:
This routine initializes the hardware. It is a generic initialization
routine for many of the Microchip development boards, using definitions
in HardwareProfile.h to determine specific initialization.
Precondition:
None
Parameters:
None - None
Returns:
None
Remarks:
None
***************************************************************************/
static void InitializeBoard(void) {
// WiFi Module hardware Initialization handled by Library
// Enable multi-vectored interrupts
INTEnableSystemMultiVectoredInt();
// Enable optimal performance
SYSTEMConfigPerformance(GetSystemClock());
mOSCSetPBDIV(OSC_PB_DIV_1); // Use 1:1 CPU Core:Peripheral clocks
// Disable JTAG port so we get our I/O pins back, but first
// wait 50ms so if you want to reprogram the part with
// JTAG, you'll still have a tiny window before JTAG goes away.
// The PIC32 Starter Kit debuggers use JTAG and therefore must not
// disable JTAG.
DelayMs(50);
DDPCONbits.JTAGEN = 0;
// LEDs
LEDS_OFF();
mPORTESetPinsDigitalOut(BIT_5 | BIT_6 | BIT_7);
// Switches
mPORTDSetPinsDigitalIn(BIT_4 | BIT_5 | BIT_6);
ConfigCNPullups(CN13_PULLUP_ENABLE | CN14_PULLUP_ENABLE | CN15_PULLUP_ENABLE);
// LCD
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3);
//Configure LCD SPI pins
mPORTFSetPinsDigitalOut(BIT_8);
mPORTDSetPinsDigitalOut(BIT_15);
//SPI Flash
mPORTDSetPinsDigitalOut(BIT_14);
//UART
mPORTFSetPinsDigitalOut(BIT_5);
mPORTFSetPinsDigitalIn(BIT_4);
//MiWi
#if defined(MRF24J40) || defined(MRF49XA)
PHY_CS = 1;
mPORTDSetPinsDigitalOut(BIT_9);
PHY_RESETn = 1;
mPORTDSetPinsDigitalOut(BIT_11);
#endif
#if defined(MRF49XA)
nFSEL_TRIS = 0;
FINT_TRIS = 1;
nFSEL = 1;
#elif defined(MRF24J40)
PHY_WAKE = 1;
mPORTBSetPinsDigitalOut(BIT_9);
#else
Data_nCS_TRIS = 0;
Config_nCS_TRIS = 0;
Data_nCS = 1;
Config_nCS = 1;
IRQ1_INT_TRIS = 1;
IRQ0_INT_TRIS = 1;
#endif
/* Set the Port Directions of SDO, SDI, Clock & Slave Select Signal */
/* Set SCK port pin to output */
mPORTDSetPinsDigitalOut(BIT_10);
/* Set SDO port pin to output */
mPORTDSetPinsDigitalOut(BIT_0);
/* Set SDI port pin to input */
mPORTCSetPinsDigitalIn(BIT_4);
/* Set INT1, INT2 port pins to input */
mPORTESetPinsDigitalIn(BIT_8 | BIT_9);
/* Clear SPI1CON register */
SPI1CONCLR = 0xFFFFFFFF;
#ifdef HARDWARE_SPI
unsigned int pbFreq;
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output data changes on transition
from active clock state to Idle clock state */
SPI1CON = 0x00008120;
/* Peripheral Bus Frequency = System Clock / PB Divider */
pbFreq = (DWORD) CLOCK_FREQ / (1 << mOSCGetPBDIV());
/* PB Frequency can be maximum 40 MHz */
if (pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)) {
{
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg1 = 1;
//For the SPI1
/* Continue the loop till you find SPI Baud Rate Register Value */
while (1) {
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg1 + 1));
if (SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P) {
break;
}
SPI_Brg1++;
}
mSpiChnSetBrg(1, SPI_Brg1);
}
} else {
/* Set SPI1 Baud Rate */
mSpiChnSetBrg(1, 0);
}
#endif
/* Set the Interrupt Priority */
mINT2SetIntPriority(4);
#if defined(MRF89XA)
mINT1SetIntPriority(4);
#endif
/* Set Interrupt Subpriority Bits for INT2 */
mINT2SetIntSubPriority(2);
#if defined(MRF89XA)
mINT2SetIntSubPriority(1);
#endif
/* Set INT2 to falling edge */
mINT2SetEdgeMode(0);
#if defined(MRF89XA)
mINT1SetEdgeMode(1);
mINT2SetEdgeMode(1);
#endif
/* Enable INT2 */
mINT2IntEnable(1);
#if defined(MRF89XA)
mINT2IntEnable(1);
#endif
/* Enable Multi Vectored Interrupts */
// INTEnableSystemMultiVectoredInt();
#if defined(MRF89XA)
PHY_IRQ1 = 0;
PHY_IRQ0 = 0;
PHY_RESETn_TRIS = 1;
#else
RFIF = 0;
if (RF_INT_PIN == 0) {
RFIF = 1;
}
#endif
// Initialize the EEPROM
XEEInit();
// UART Initialization
#if defined(STACK_USE_UART)
UARTTX_TRIS = 0;
UARTRX_TRIS = 1;
UMODE = 0x8000; // Set UARTEN. Note: this must be done before setting UTXEN
USTA = 0x00001400; // RXEN set, TXEN set
#define CLOSEST_UBRG_VALUE ((GetPeripheralClock()+8ul*BAUD_RATE)/16/BAUD_RATE-1)
#define BAUD_ACTUAL (GetPeripheralClock()/16/(CLOSEST_UBRG_VALUE+1))
#define BAUD_ERROR ((BAUD_ACTUAL > BAUD_RATE) ? BAUD_ACTUAL-BAUD_RATE : BAUD_RATE-BAUD_ACTUAL)
#define BAUD_ERROR_PRECENT ((BAUD_ERROR*100+BAUD_RATE/2)/BAUD_RATE)
#if (BAUD_ERROR_PRECENT > 3)
#warning UART frequency error is worse than 3%
#elif (BAUD_ERROR_PRECENT > 2)
#warning UART frequency error is worse than 2%
#endif
UBRG = CLOSEST_UBRG_VALUE;
#endif
}
main()
{
// Disable JTAG (on RA0 and RA1 )
mJTAGPortEnable( DEBUG_JTAGPORT_OFF );
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(GetSystemClock(), SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
initializeUART();
initializeADC();
initializeLCD();
initializeRPG();
/* Initialize SD card */
setup_SDSPI();
SD_setStart();
/* Fill tempBuffer[] with int 0 to 63
* Write it to the current block.
* Empty tempBuffer[] to all 0.
* Read from the current block to make sure that it returns the right value.
*/
fillTempBuffer();
testSDReadWrite(tempBuffer);
curr_read_block = curr_block;
ConfigTimer1(); // Enable Timer1 for second counts
configureInterrupts();
// T2CON = 0x8030; // TMR1 on, prescale 1:256 PB
mPORTASetPinsDigitalOut( LED_MASK ); // LEDs = output
mPORTDSetPinsDigitalIn( PB_MASK_D ); // PBs on D = input
curr_state = READY;
// enable interrupts
INTEnableInterrupts();
int i = 0;
while( 1 )
{
if (getPrintToUARTFlag() == 1){
LCDMenuControl();
//mPORTAToggleBits( LED_MASK );
convertAndPrintIntegerToString("i => ", i++);
convertAndPrintIntegerToString("timeElapse => ", timeElapsed);
convertAndPrintIntegerToString("timeElapsedLEDSample => ", timeElapsedLEDSample);
convertAndPrintIntegerToString("timeElapsedLEDTurnedOff => ", timeElapsedLEDTurnedOff);
convertAndPrintIntegerToString("sampleLEDNow => ", sampleLEDNow);
convertAndPrintIntegerToString(" ADC Value => ", getChannel5Value());
printShadowDetect();
printLightLevel();
drawLightDetectedBar();
controlPowerRelay();
switch(curr_state) {
case READY : WriteString("State => READY ");
break;
case SLEEP : WriteString("State => SLEEP ");
break;
case HIBERNATE : WriteString("State => HIBERNATE");
break;
case BUSY : WriteString("State => BUSY ");
break;
}
WriteString("\r");
setPrintToUARTFlag(0);
}
if (NEW_BYTE_RECEIVED == 1){
curr_state = READY;
NEW_BYTE_RECEIVED = 0;
//mPORTAToggleBits( LED_MASK );
char tempArray[] = "g";
tempArray[0] = characterByteReceived;
WriteString(tempArray);
if(curr_state = HIBERNATE) {
addByteToBuffer(characterByteReceived);
}
else {
PutCharacter(characterByteReceived);
}
}
if(bufferIndex == 512) {
SDWriteBlock(currBlock);
currBlock++;
bufferIndex = 0;
}
if((curr_state == READY) && (timeElapsed >= SLEEP_TIMEOUT) && (timeElapsed < HIBERNATE_TIMEOUT)) {
curr_state = SLEEP;
}
else if((curr_state == SLEEP) && (timeElapsed >= HIBERNATE_TIMEOUT)) {
curr_state = HIBERNATE;
timeElapsed = 0;
}
if (transmitDataFromSDCard == 1) {
transmitDataFromSDCard = 0;
forwardDataToPrinter();
}
} // main (while) loop
return 0;
} // main
//********************************
//********************************
//********** INITIALISE **********
//********************************
//********************************
void initialise (void)
{
BYTE data;
//##### GENERAL NOTE ABOUT PIC32'S #####
//Try and use the peripheral libraries instead of special function registers for everything (literally everything!) to avoid
//bugs that can be caused by the pipeline and interrupts.
//---------------------------------
//----- CONFIGURE PERFORMANCE -----
//---------------------------------
//----- SETUP EVERYTHING FOR OPTIMUM PERFORMANCE -----
SYSTEMConfigPerformance(80000000ul); //Note this sets peripheral bus to '1' max speed (regardless of configuration bit setting)
//Use PBCLK divider of 1:1 to calculate UART baud, timer tick etc
//----- SET PERIPHERAL BUS DIVISOR -----
//To minimize dynamic power the PB divisor should be chosen to run the peripherals at the lowest frequency that provides acceptable system performance
mOSCSetPBDIV(OSC_PB_DIV_2); //OSC_PB_DIV_1, OSC_PB_DIV_2, OSC_PB_DIV_4, OSC_PB_DIV_8,
//----- SETUP INTERRUPTS -----
INTEnableSystemMultiVectoredInt();
//-------------------------
//----- SETUP IO PINS -----
//-------------------------
//(Device will powerup with all IO pins as inputs)
//----- TURN OFF THE JTAG PORT -----
//(JTAG is on by default)
//mJTAGPortEnable(0); //Must be on for Microchip Multimedia Development board
#define PORTA_IO 0xc2ff //Setup the IO pin type (0 = output, 1 = input)
mPORTAWrite(0xc033); //Set initial ouput pin states
mPORTASetPinsDigitalIn(PORTA_IO); //(Sets high bits as input)
mPORTASetPinsDigitalOut(~PORTA_IO); //(Sets high bits as output)
#define PORTB_IO 0xfbff //Setup the IO pin type (0 = output, 1 = input)
mPORTBWrite(0x6d13); //Set initial ouput pin states
mPORTBSetPinsDigitalIn(PORTB_IO); //(Sets high bits as input)
mPORTBSetPinsDigitalOut(~PORTB_IO); //(Sets high bits as output)
mPORTBSetPinsDigitalIn(BIT_0 | BIT_1 | BIT_3 | BIT_4 | BIT_15); //Joystick inputs
#define PORTC_IO 0xf01e //Setup the IO pin type (0 = output, 1 = input)
mPORTCWrite(0x3018); //Set initial ouput pin states
mPORTCSetPinsDigitalIn(PORTC_IO); //(Sets high bits as input)
mPORTCSetPinsDigitalOut(~PORTC_IO); //(Sets high bits as output)
#define PORTD_IO 0x7bfe //Setup the IO pin type (0 = output, 1 = input)
mPORTDWrite(0xbdaf); //Set initial ouput pin states
mPORTDSetPinsDigitalIn(PORTD_IO); //(Sets high bits as input)
mPORTDSetPinsDigitalOut(~PORTD_IO); //(Sets high bits as output)
mPORTDSetPinsDigitalOut(BIT_2 | BIT_1); //LED's 2 and 3
mPORTDSetPinsDigitalIn(BIT_9);
#define PORTE_IO 0x03ff //Setup the IO pin type (0 = output, 1 = input)
mPORTEWrite(0x02a2); //Set initial ouput pin states
mPORTESetPinsDigitalIn(PORTE_IO); //(Sets high bits as input)
mPORTESetPinsDigitalOut(~PORTE_IO); //(Sets high bits as output)
#define PORTF_IO 0x111f //Setup the IO pin type (0 = output, 1 = input)
mPORTFWrite(0x0039); //Set initial ouput pin states
mPORTFSetPinsDigitalIn(PORTF_IO); //(Sets high bits as input)
mPORTFSetPinsDigitalOut(~PORTF_IO); //(Sets high bits as output)
#define PORTG_IO 0xd3cf //Setup the IO pin type (0 = output, 1 = input)
mPORTGWrite(0xf203); //Set initial ouput pin states
mPORTGSetPinsDigitalIn(PORTG_IO); //(Sets high bits as input)
mPORTGSetPinsDigitalOut(~PORTG_IO); //(Sets high bits as output)
//Read pins using:
// mPORTAReadBits(BIT_0);
//Write pins using:
// mPORTAClearBits(BIT_0);
// mPORTASetBits(BIT_0);
// mPORTAToggleBits(BIT_0);
//----- INPUT CHANGE NOTIFICATION CONFIGURATION -----
//EnableCN0();
ConfigCNPullups(CN2_PULLUP_ENABLE | CN3_PULLUP_ENABLE | CN5_PULLUP_ENABLE | CN6_PULLUP_ENABLE | CN12_PULLUP_ENABLE); //Joystick pins
//----- SETUP THE A TO D PINS -----
ENABLE_ALL_DIG;
//---------------------
//----- SETUP USB -----
//---------------------
//The USB specifications require that USB peripheral devices must never source current onto the Vbus pin. Additionally, USB peripherals should not source
//current on D+ or D- when the host/hub is not actively powering the Vbus line. When designing a self powered (as opposed to bus powered) USB peripheral
//device, the firmware should make sure not to turn on the USB module and D+ or D- pull up resistor unless Vbus is actively powered. Therefore, the
//firmware needs some means to detect when Vbus is being powered by the host. A 5V tolerant I/O pin can be connected to Vbus (through a resistor), and
//can be used to detect when Vbus is high (host actively powering), or low (host is shut down or otherwise not supplying power). The USB firmware
//can then periodically poll this I/O pin to know when it is okay to turn on the USB module/D+/D- pull up resistor. When designing a purely bus powered
//peripheral device, it is not possible to source current on D+ or D- when the host is not actively providing power on Vbus. Therefore, implementing this
//bus sense feature is optional. This firmware can be made to use this bus sense feature by making sure "USE_USB_BUS_SENSE_IO" has been defined in the
//HardwareProfile.h file.
// #if defined(USE_USB_BUS_SENSE_IO)
// tris_usb_bus_sense = INPUT_PIN; // See HardwareProfile.h
// #endif
//If the host PC sends a GetStatus (device) request, the firmware must respond and let the host know if the USB peripheral device is currently bus powered
//or self powered. See chapter 9 in the official USB specifications for details regarding this request. If the peripheral device is capable of being both
//self and bus powered, it should not return a hard coded value for this request. Instead, firmware should check if it is currently self or bus powered, and
//respond accordingly. If the hardware has been configured like demonstrated on the PICDEM FS USB Demo Board, an I/O pin can be polled to determine the
//currently selected power source. On the PICDEM FS USB Demo Board, "RA2" is used for this purpose. If using this feature, make sure "USE_SELF_POWER_SENSE_IO"
//has been defined in HardwareProfile.h, and that an appropriate I/O pin has been mapped to it in HardwareProfile.h.
// #if defined(USE_SELF_POWER_SENSE_IO)
// tris_self_power = INPUT_PIN; // See HardwareProfile.h
// #endif
//Enable the USB port now - we will check to see if Vbus is powered at the end of init and disable it if not.
//USBDeviceInit(); //usb_device.c. Initializes USB module SFRs and firmware variables to known states.
//------------------------
//----- SETUP TIMERS -----
//------------------------
//(INCLUDE THE USAGE OF ALL TIMERS HERE EVEN IF NOT SETUP HERE SO THIS IS THE ONE POINT OF
//REFERENCE TO KNOW WHICH TIMERS ARE IN USE AND FOR WHAT).
//----- SETUP TIMER 1 -----
//Used for: Available
//OpenTimer1((T1_ON | T1_IDLE_CON | T1_GATE_OFF | T1_PS_1_4 | T1_SOURCE_INT), 20000);
//----- SETUP TIMER 2 -----
//Used for:
//OpenTimer2((T2_ON | T2_IDLE_CON | T2_GATE_OFF | T2_PS_1_1 | T2_SOURCE_INT), 0xffff); //0xffff = 305Hz
//----- SETUP TIMER 3 -----
//Used for:
//OpenTimer3((T3_ON | T3_IDLE_CON | T3_GATE_OFF | T3_PS_1_1 | T3_SOURCE_INT), PIEZO_TIMER_PERIOD);
//----- SETUP TIMER 4 -----
//Used for:
//OpenTimer4((T4_ON | T4_IDLE_CON | T4_GATE_OFF | T4_PS_1_1 | T4_SOURCE_INT), 20000);
//----- SETUP TIMER 5 -----
//Used for: Heartbeat
OpenTimer5((T5_ON | T5_IDLE_CON | T5_GATE_OFF | T5_PS_1_1 | T5_SOURCE_INT), 40000); //1mS with 80MHz osc and PB_DIV_2
ConfigIntTimer5(T5_INT_ON | T5_INT_PRIOR_7); //1=lowest priority to 7=highest priority. ISR function must specify same value
//---------------------------------
//----- SETUP EVAL BOARD CPLD -----
//---------------------------------
//Graphics bus width = 16
mPORTGSetPinsDigitalOut(BIT_14);
mPORTGSetBits(BIT_14);
//SPI source select = SPI3 (not used)
mPORTGSetPinsDigitalOut(BIT_12);
mPORTGClearBits(BIT_12);
//SPI peripheral destination select = Expansion Slot (not used)
mPORTASetPinsDigitalOut(BIT_7 | BIT_6);
mPORTASetBits(BIT_7);
mPORTAClearBits(BIT_6);
//--------------------------------------
//----- PARALLEL MASTER PORT SETUP -----
//--------------------------------------
PMMODE = 0;
PMAEN = 0;
PMCON = 0;
PMMODE = 0x0610;
PMCONbits.PTRDEN = 1; //Enable RD line
PMCONbits.PTWREN = 1; //Enable WR line
PMCONbits.PMPEN = 1; //Enable PMP
//------------------------------
//----- INITIALISE DISPLAY -----
//------------------------------
display_initialise();
display_test();
//LOAD OUR GLOBAL HTML STYLES FILE READY FOR DISPLAY HTML PAGES
BYTE dummy_styles_count;
DWORD file_size;
if (display_html_setup_read_file(global_css, 0, &file_size))
{
dummy_styles_count = 0;
display_html_read_styles(&file_size, &dummy_styles_count, 1); //1 = this is global styles file
}
}
int main() {
// Initialize Sockets and IP address containers
//
SOCKET serverSock, clientSock = INVALID_SOCKET;
IP_ADDR curr_ip, ip;
// Initialize buffer length variables
//
int rlen, sent, bytesSent;
// Initialize the Send/Recv buffers
//
char rbfr[10];
// Socket struct descriptor
//
struct sockaddr_in addr;
int addrlen = sizeof(struct sockaddr_in);
// System clock containers
//
unsigned int sys_clk, pb_clk;
// Initialize LED Variables:
// Setup the LEDs on the PIC32 board
// RD0, RD1 and RD2 as outputs
//
mPORTDSetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 );
mPORTDClearBits(BIT_0 | BIT_1 | BIT_2); // Clear previous LED status.
// Setup the switches on the PIC32 board as inputs
//
mPORTDSetPinsDigitalIn(BIT_6 | BIT_7 | BIT_13); // RD6, RD7, RD13 as inputs
// Setup the system clock to use CPU frequency
//
sys_clk = GetSystemClock();
pb_clk = SYSTEMConfigWaitStatesAndPB(sys_clk);
// interrupts enabled
INTEnableSystemMultiVectoredInt();
// system clock enabled
SystemTickInit(sys_clk, TICKS_PER_SECOND);
// Initialize TCP/IP
//
TCPIPSetDefaultAddr(DEFAULT_IP_ADDR, DEFAULT_IP_MASK, DEFAULT_IP_GATEWAY,
DEFAULT_MAC_ADDR);
if (!TCPIPInit(sys_clk)) return -1;
DHCPInit();
// Port to bind socket to
//
addr.sin_port = 6653;
addr.sin_addr.S_un.S_addr = IP_ADDR_ANY;
// Initialize TCP server socket
//
if((serverSock = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP)) ==
SOCKET_ERROR) return -1;
// Ensure we bound to the socket. End Program if bind fails
//
if(bind(serverSock, (struct sockaddr*) &addr, addrlen ) ==
SOCKET_ERROR)
return -1;
// Listen to up to five clients on server socket
//
listen(serverSock, 5);
// We store our desired transfer paragraph
//
char myStr[] = "TCP/IP (Transmission Control Protocol/Internet Protocol) is "
"the basic communication language or protocol of the Internet. "
"It can also be used as a communications protocol in a private "
"network (either an intranet or an extranet). When you are set up "
"with direct access to the Internet, your computer is provided "
"with a copy of the TCP/IP program just as every other computer "
"that you may send messages to or get information from also has "
"a copy of TCP/IP. TCP/IP is a two-layer program. The higher "
"layer, Transmission Control Protocol, manages the assembling "
"of a message or file into smaller packets that are transmitted "
"over the Internet and received by a TCP layer that reassembles "
"the packets into the original message. The lower layer, "
"Internet Protocol, handles the address part of each packet so "
"that it gets to the right destination. Each gateway computer on "
"the network checks this address to see where to forward the "
"message. Even though some packets from the same message are "
"routed differently than others, they'll be reassembled at the "
"destination.\0";
// Chunk up our data
//
// Copy our string into our buffer
//
int tlen = strlen(myStr);
char tbfr1[tlen1+1];
// Loop forever
//
while(1) {
// Refresh TCIP and DHCP
//
TCPIPProcess();
DHCPTask();
// Get the machines IP address and save to variable
//
ip.Val = TCPIPGetIPAddr();
// DHCP server change IP address?
//
if(curr_ip.Val != ip.Val) curr_ip.Val = ip.Val;
// TCP Server Code
//
if(clientSock == INVALID_SOCKET) {
// Start listening for incoming connections
//
clientSock = accept(serverSock, (struct sockaddr*) &addr, &addrlen);
// Upon connection to a client blink LEDS.
//
if(clientSock != INVALID_SOCKET) {
setsockopt(clientSock, SOL_SOCKET, TCP_NODELAY,
(char*)&tlen, sizeof(int));
mPORTDSetBits(BIT_0); // LED1=1
DelayMsec(50);
mPORTDClearBits(BIT_0); // LED1=0
mPORTDSetBits(BIT_1); // LED2=1
DelayMsec(50);
mPORTDClearBits(BIT_1); // LED2=0
mPORTDSetBits(BIT_2); // LED3=1
DelayMsec(50);
mPORTDClearBits(BIT_2); // LED3=0
}
}
else {
// We are connected to a client already. We start
// by receiving the message being sent by the client
//
rlen = recvfrom(clientSock, rbfr, sizeof(rbfr), 0, NULL,
NULL);
// Check to see if socket is still alive
//
if(rlen > 0) {
// If the received message first byte is '02' it signifies
// a start of message
//
if (rbfr[0]==2) {
//mPORTDSetBits(BIT_0); // LED1=1
// Check to see if message begins with
// '0271' to see if the message is a a global reset
//
if(rbfr[1]==71) {
mPORTDSetBits(BIT_0); // LED1=1
DelayMsec(50);
mPORTDClearBits(BIT_0); // LED1=0
}
}
// If the received message starts with a second byte is
// '84' it signifies a initiate transfer
//
if(rbfr[1]==84){
mPORTDSetBits(BIT_2); // LED3=1
bytesSent = 0;
//sent = 0;
while (bytesSent < tlen){
memcpy(tbfr1, myStr+bytesSent, tlen1);
if (bytesSent > 1049){
tbfr1[tlen-bytesSent+1] = '\0';
send(clientSock, tbfr1, tlen-bytesSent+1, 0);
}
else{
tbfr1[tlen1] = '\0';
// Loop until we send the full message
//
send(clientSock, tbfr1, tlen1+1, 0);
}
bytesSent += tlen1;
DelayMsec(50);
}
mPORTDClearBits(BIT_2); // LED3=0
}
mPORTDClearBits(BIT_0); // LED1=0
}
// The client has closed the socket so we close as well
//
else if(rlen < 0) {
closesocket(clientSock);
clientSock = SOCKET_ERROR;
}
}
}
}
/*******************************************************************************
* Function: BoardInit(void)
* PreCondition:None
* Input: None
* Output: None
* Overview: SPI pins and SFR, Maintenance Tasks Timer, External Interrupts,
* and other board issues initialization.
* Note: This routine needs to be called before initialising MiWi stack
* or invoking other function that operates on MiWi stack.
******************************************************************************/
void BoardInit(void){
#if defined(__PIC32MX__)
// RADIO INTERFACES & SPI INIT -------------------------------------------//
#if defined HARDWARE_SPI
/* Peripheral Bus Frequency = System Clock / PB Divider */
unsigned int pbFreq;
pbFreq = (DWORD) CLOCK_FREQ/(1 << mOSCGetPBDIV());
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg;
#endif
#if defined MRF24J40
PHY_CS_TRIS = OUTPUT_PIN;
PHY_CS = 1;
PHY_RESETn_TRIS = OUTPUT_PIN;
PHY_RESETn = 1;
MRF24J40_INT_TRIS = INPUT_PIN;
SDI_TRIS = INPUT_PIN;
SDO_TRIS = OUTPUT_PIN;
SCK_TRIS = OUTPUT_PIN;
SPI_SDO = 0;
SPI_SCK = 0;
PHY_WAKE_TRIS = OUTPUT_PIN;
PHY_WAKE = 1;
MRF24J40_PWR_TRIS = OUTPUT_PIN;
MRF24J40_PWR = 1;
SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
else{
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, 0);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
#endif
#endif
#if defined(MRF49XA_1)
// pruebas de funcionamiento
/* MRF49XA_1_PHY_CS_TRIS = OUTPUT_PIN;
MRF49XA_1_PHY_CS = 0;
MRF49XA_1_PHY_CS = 1;
MRF49XA_1_PHY_RESETn_TRIS = OUTPUT_PIN;
MRF49XA_1_PHY_RESETn = 0;
MRF49XA_1_PHY_RESETn = 1;
MRF49XA_1_INT_TRIS = OUTPUT_PIN;
MRF49XA_1_INT_PIN = 0;
MRF49XA_1_INT_PIN = 1;
MRF49XA_1_SDI_TRIS = OUTPUT_PIN;
MRF49XA_1_SPI_SDI = 0;
MRF49XA_1_SPI_SDI = 1;
MRF49XA_1_SDO_TRIS = OUTPUT_PIN;
MRF49XA_1_SPI_SDO = 0;
MRF49XA_1_SPI_SDO = 1;
MRF49XA_1_SCK_TRIS = OUTPUT_PIN;
MRF49XA_1_SPI_SCK = 0;
MRF49XA_1_SPI_SCK = 1;
MRF49XA_1_nFSEL_TRIS = OUTPUT_PIN;
MRF49XA_1_nFSEL = 0;
MRF49XA_1_nFSEL = 1;
MRF49XA_1_FINT_TRIS = OUTPUT_PIN;
MRF49XA_1_FINT = 0;
MRF49XA_1_FINT = 1;
*/
// configuration. Juan: Added; Agus: Modified to a standard way
MRF49XA_1_PHY_CS_TRIS = OUTPUT_PIN;
MRF49XA_1_PHY_CS = 1;
MRF49XA_1_PHY_RESETn_TRIS = OUTPUT_PIN;
MRF49XA_1_PHY_RESETn = 1;
MRF49XA_1_INT_TRIS = INPUT_PIN;
MRF49XA_1_SDI_TRIS = INPUT_PIN;
MRF49XA_1_SDO_TRIS = OUTPUT_PIN;
MRF49XA_1_SCK_TRIS = OUTPUT_PIN;
MRF49XA_1_SPI_SDO = 0;
MRF49XA_1_SPI_SCK = 0;
MRF49XA_1_nFSEL_TRIS = OUTPUT_PIN;
MRF49XA_1_FINT_TRIS = INPUT_PIN;
MRF49XA_1_nFSEL = 1; // nFSEL inactive
#ifdef cNGD_PLATFORM
// MRF49XA_1_PWR_TRIS = OUTPUT_PIN;
// MRF49XA_1_PWR = 1;
#endif
MRF49XA_1_SPICONCLR = 0xFFFFFFFF; //Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_1_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
#if defined(MRF49XA_2)
MRF49XA_2_PHY_CS_TRIS = OUTPUT_PIN;
MRF49XA_2_PHY_CS = 1;
MRF49XA_2_PHY_RESETn_TRIS = OUTPUT_PIN;
MRF49XA_2_PHY_RESETn = 1;
MRF49XA_2_INT_TRIS = 1;
MRF49XA_2_SDI_TRIS = INPUT_PIN;
MRF49XA_2_SDO_TRIS = OUTPUT_PIN;
MRF49XA_2_SCK_TRIS = OUTPUT_PIN;
MRF49XA_2_SPI_SDO = 0;
MRF49XA_2_SPI_SCK = 0;
MRF49XA_2_nFSEL_TRIS = OUTPUT_PIN;
MRF49XA_2_FINT_TRIS = INPUT_PIN;
MRF49XA_2_nFSEL = 1; // nFSEL inactive
#ifdef cNGD_PLATFORM
MRF49XA_2_PWR_TRIS = OUTPUT_PIN;
MRF49XA_2_PWR = 1;
#endif
MRF49XA_2_SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_2_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
#if defined MRF89XA
Data_nCS_TRIS = 0;
Config_nCS_TRIS = 0;
Data_nCS = 1;
Config_nCS = 1;
PHY_IRQ1_TRIS = 1;
//... REVIEW...
#endif
// SPI & EXTERNAL INTERRUPTS PINS AND CONFIGURATION ----------------------//
/* Set the SPI Port Directions (SDO, SDI, SCK) for every SPI module.*/
#if defined SPI1_IN_USE
SDI1_TRIS = INPUT_PIN; //DIGITAL IN
SDO1_TRIS = OUTPUT_PIN; //DIGITAL OUT
SCK1_TRIS = OUTPUT_PIN; //DIGITAL OUT
#endif
#if defined SPI2_IN_USE
SDI2_TRIS = INPUT_PIN; //DIGITAL IN
SDO2_TRIS = OUTPUT_PIN; //DIGITAL OUT
SCK2_TRIS = OUTPUT_PIN; //DIGITAL OUT
#endif
#if defined SPI3_IN_USE
SDI3_TRIS = INPUT_PIN; //DIGITAL IN
SDO3_TRIS = OUTPUT_PIN; //DIGITAL OUT
SCK3_TRIS = OUTPUT_PIN; //DIGITAL OUT
#endif
#if defined SPI4_IN_USE
SDI4_TRIS = INPUT_PIN; //DIGITAL IN
SDO4_TRIS = OUTPUT_PIN; //DIGITAL OUT
SCK4_TRIS = OUTPUT_PIN; //DIGITAL OUT
#endif
/* Set the external interrups Pin Directions and Priority*/
#if defined INT1_IN_USE
INT1_TRIS = INPUT_PIN; // DIGITAL IN
mINT1SetIntPriority(4);
mINT1SetIntSubPriority(2);
mINT1SetEdgeMode(0); //0: Falling Edge.
// Enable INT1
mINT1IntEnable(1);
#endif
#if defined INT2_IN_USE
INT2_TRIS = INPUT_PIN; // DIGITAL IN
mINT2SetIntPriority(4);
mINT2SetIntSubPriority(2);
mINT2SetEdgeMode(0); //0: Falling Edge.
/* Enable INT2 */
mINT2IntEnable(1);
#endif
#if defined INT3_IN_USE
INT3_TRIS = INPUT_PIN; // DIGITAL IN
mINT3SetIntPriority(4);
mINT3SetIntSubPriority(2);
mINT3SetEdgeMode(0); //0: Falling Edge.
/* Enable INT3 */
mINT3IntEnable(1);
#endif
#if defined INT4_IN_USE
INT4_TRIS = INPUT_PIN; // DIGITAL IN
mINT4SetIntPriority(4);
mINT4SetIntSubPriority(2);
mINT4SetEdgeMode(0); //0: Falling Edge.
/* Enable INT4 */
mINT4IntEnable(1);
#endif
// LEDs
#ifdef cNGD_PLATFORM
mJTAGPortEnable(0); //Needed due to multiplexed pins
LED1_TRIS = OUTPUT_PIN;
LED2_TRIS = OUTPUT_PIN;
LED3_TRIS = OUTPUT_PIN;
LED1 = 0;
LED2 = 0;
LED3 = 0;
#endif
// TIMER 1 FOR TIME_SYNC -------------------------------------------------//
#if defined(ENABLE_TIME_SYNC)
//TIMER 1 MAY BE USED FOR SLEEP MODE AND/OR FOR STACKS MAINTENANCE. IT
//NEEDS ADAPTATION BEFORE ENABLING TIME_SYNC WITH TIMER 1 TOO!
T1CON = 0;
T1CON = 0x0012;
T1CONSET = 0x8000;
PR1 = 0xFFFF;
IFS0bits.T1IF = 0;
mT1IntEnable(1);
mT1SetIntPriority(4);
while(T1CONbits.TWIP);
TMR1 = 0;
#endif
// TIMER 1 FOR NODE STACKS AUTO-MAINTENANCE ------------------------------//
#if defined NODE_DOES_MAINTENANCE_TASKS
T1CON = 0x0070; //Disable timer, PBCLK source, PS=256
TMR1 = 0x0000; //Reset count
PR1 = MAINTENANCE_PERIOD; //Set period.
IPC1SET = 0x00000005; //Set Priority level 1, Subpriority level 1
IFS0CLR = 0x00000010; //Clear T1IF
IEC0SET = 0x00000010; //Set T1IE
//Timer will be triggered after initialization.
#endif
//************************************* TODO
// IOPORT CN - For waking up the node manually. --------------------------//
mPORTDSetPinsDigitalIn(BIT_5); // CN14
CNCON = 0x8000; //Module enabled.
CNEN = 0x00004000; //Enable CN14
CNPUE = 0x00004000; //Enable CN14 weak pull-up.
ReadBUTTONS(); //Clear PORT mismatch condition.
IFS1CLR = 0x00000001; //Clear the CN interrupt flag status bit
IPC6SET = 0x00180000; //Set CN priority 6, subpriority 0.
//It will be enabled only during sleep mode time interval
//------------------------------------------------------------------------//
// Lo modifico en el wifi config
#if defined(ENABLE_NVM) //REVIEW
//EE_nCS_TRIS = 0;//FERNANDO, CUIDADO NO SE SI LA PILA REALMENTE FUNCIONA CON FLASH MEMORY
//EE_nCS = 1;
#endif
// INTERRUPTION FLAGS AND EXT_INT PIN FINAL SETTINGS ---------------------//
#if defined MRF49XA_1
MRF49XA_1_IF = 0;
if(MRF49XA_1_INT_PIN == 0){
MRF49XA_1_IF = 1;
}
#endif
#if defined MRF49XA_2
MRF49XA_2_IF = 0;
if(MRF49XA_2_INT_PIN == 0){
MRF49XA_2_IF = 1;
}
#endif
#if defined MRF89XA
PHY_IRQ1 = 0;
#endif
#if defined MRF24J40
MRF24J40_IF = 0;
if(MRF24J40_INT_PIN == 0){
MRF24J40_IF = 1;
}
#endif
#else //Not PIC32.
#error "Unknown target board."
#endif
}
/*******************************************************************************
* Function: BoardInit(void)
* PreCondition:None
* Input: None
* Output: None
* Overview: SPI pins and SFR, Maintenance Tasks Timer, External Interrupts,
* and other board issues initialization.
* Note: This routine needs to be called before initialising MiWi stack
* or invoking other function that operates on MiWi stack.
******************************************************************************/
void BoardInit(void){
#if defined(__PIC32MX__)
// RADIO INTERFACES & SPI INIT -------------------------------------------//
#if defined HARDWARE_SPI
/* Peripheral Bus Frequency = System Clock / PB Divider */
unsigned int pbFreq;
pbFreq = (DWORD) CLOCK_FREQ/(1 << mOSCGetPBDIV());
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg;
#endif
#if defined MRF24J40
PHY_CS_TRIS = 0;
PHY_CS = 1;
PHY_RESETn_TRIS = 0;
PHY_RESETn = 1;
MRF24J40_INT_TRIS = 1;
SDI_TRIS = 1;
SDO_TRIS = 0;
SCK_TRIS = 0;
SPI_SDO = 0;
SPI_SCK = 0;
PHY_WAKE_TRIS = 0;
PHY_WAKE = 1;
SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
else{
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, 0);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
#endif
#endif
#if defined(MRF49XA_1)
//Configuration for Guilja's Expansion Board, Connection SLot 1 --//
mPORTESetPinsDigitalOut(BIT_1); //nCS
mPORTBSetPinsDigitalIn(BIT_2); //FINT //Juan: Added.
//----------------------------------------------------------------//
MRF49XA_1_PHY_CS_TRIS = 0;
MRF49XA_1_PHY_CS = 1;
MRF49XA_1_PHY_RESETn_TRIS = 0;
MRF49XA_1_PHY_RESETn = 1;
MRF49XA_1_INT_TRIS = 1;
MRF49XA_1_SDI_TRIS = 1;
MRF49XA_1_SDO_TRIS = 0;
MRF49XA_1_SCK_TRIS = 0;
MRF49XA_1_SPI_SDO = 0;
MRF49XA_1_SPI_SCK = 0;
MRF49XA_1_nFSEL_TRIS = 0;
MRF49XA_1_FINT_TRIS = 1;
MRF49XA_1_nFSEL = 1; // nFSEL inactive
MRF49XA_1_SPICONCLR = 0xFFFFFFFF; //Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_1_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
#if defined(MRF49XA_2)
MRF49XA_2_PHY_CS_TRIS = 0;
MRF49XA_2_PHY_CS = 1;
MRF49XA_2_PHY_RESETn_TRIS = 0;
MRF49XA_2_PHY_RESETn = 1;
MRF49XA_2_INT_TRIS = 1;
MRF49XA_2_SDI_TRIS = 1;
MRF49XA_2_SDO_TRIS = 0;
MRF49XA_2_SCK_TRIS = 0;
MRF49XA_2_SPI_SDO = 0;
MRF49XA_2_SPI_SCK = 0;
MRF49XA_2_nFSEL_TRIS = 0;
MRF49XA_2_FINT_TRIS = 1;
MRF49XA_2_nFSEL = 1; // nFSEL inactive
MRF49XA_2_SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_2_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
// SPI & EXTERNAL INTERRUPTS PINS AND CONFIGURATION ----------------------//
#if (defined __32MX675F256L__ || defined ____32MX675F512__)
/* Set the SPI Port Directions (SDO, SDI, SCK) for every SPI module.*/
#if defined MRF49XA_1_IN_SPI1 || defined MRF49XA_2_IN_SPI1 || \
defined MRF89XA_IN_SPI1 || defined MRF24J40_IN_SPI1 || \
defined MRF24WB0M_IN_SPI1
mPORTDSetPinsDigitalOut(BIT_0); //SDO1
mPORTDSetPinsDigitalOut(BIT_10); //SCK1
mPORTCSetPinsDigitalIn(BIT_4); //SDI1
#endif
#if defined MRF49XA_1_IN_SPI2 || defined MRF49XA_2_IN_SPI2 || \
defined MRF89XA_IN_SPI2 || defined MRF24J40_IN_SPI2 || \
defined MRF24WB0M
mPORTGSetPinsDigitalOut(BIT_8); //SDO2
mPORTGSetPinsDigitalOut(BIT_6); //SCK2
mPORTGSetPinsDigitalIn(BIT_7); //SDI2
#endif
#if defined MRF49XA_1_IN_SPI3 || defined MRF49XA_2_IN_SPI3 || \
defined MRF89XA_IN_SPI3 || defined MRF24J40_IN_SPI3 || \
defined MRF24WB0M
mPORTFSetPinsDigitalOut(BIT_8); //SDO3
mPORTDSetPinsDigitalOut(BIT_15); //SCK3
mPORTFSetPinsDigitalIn(BIT_2); //SDI3
#endif
// #if defined MRF24WB0M_IN_SPI4
// mPORTFSetPinsDigitalOut(BIT_5); //SDO4
// mPORTFSetPinsDigitalOut(BIT_13); //SCK4
// mPORTFSetPinsDigitalIn(BIT_4); //SDI4
// #endif
#endif
#endif
// TIMER 1 FOR TIME_SYNC -------------------------------------------------//
#if defined(ENABLE_TIME_SYNC)
//TIMER 1 MAY BE USED FOR SLEEP MODE AND/OR FOR STACKS MAINTENANCE. IT
//NEEDS ADAPTATION BEFORE ENABLING TIME_SYNC WITH TIMER 1 TOO!
T1CON = 0;
T1CON = 0x0012;
T1CONSET = 0x8000;
PR1 = 0xFFFF;
IFS0bits.T1IF = 0;
mT1IntEnable(1);
mT1SetIntPriority(4);
while(T1CONbits.TWIP);
TMR1 = 0;
#endif
// TIMER 1 FOR NODE STACKS AUTO-MAINTENANCE ------------------------------//
#if defined NODE_DOES_MAINTENANCE_TASKS
T1CON = 0x0070; //Disable timer, PBCLK source, PS=256
TMR1 = 0x0000; //Reset count
PR1 = MAINTENANCE_PERIOD; //Set period.
IPC1SET = 0x00000005; //Set Priority level 1, Subpriority level 1
IFS0CLR = 0x00000010; //Clear T1IF
IEC0SET = 0x00000010; //Set T1IE
//Timer will be triggered after initialization.
#endif
// IOPORT CN - For waking up the node manually. --------------------------//
mPORTDSetPinsDigitalIn(BIT_5); // CN14
CNCON = 0x8000; //Module enabled.
CNEN = 0x00004000; //Enable CN14
CNPUE = 0x00004000; //Enable CN14 weak pull-up.
ReadBUTTONS(); //Clear PORT mismatch condition.
IFS1CLR = 0x00000001; //Clear the CN interrupt flag status bit
IPC6SET = 0x00180000; //Set CN priority 6, subpriority 0.
//It will be enabled only during sleep mode time interval
//------------------------------------------------------------------------//
// Lo modifico en el wifi config
#if defined(ENABLE_NVM) //REVIEW
//EE_nCS_TRIS = 0;//FERNANDO, CUIDADO NO SE SI LA PILA REALMENTE FUNCIONA CON FLASH MEMORY
//EE_nCS = 1;
#endif
// INTERRUPTION FLAGS AND EXT_INT PIN FINAL SETTINGS ---------------------//
#if defined MRF49XA_1
MRF49XA_1_IF = 0;
if(MRF49XA_1_INT_PIN == 0){
MRF49XA_1_IF = 1;
}
#endif
#if defined MRF49XA_2
MRF49XA_2_IF = 0;
if(MRF49XA_2_INT_PIN == 0){
MRF49XA_2_IF = 1;
}
#endif
#if defined MRF89XA
PHY_IRQ1 = 0;
#endif
#if defined MRF24J40
MRF24J40_IF = 0;
if(MRF24J40_INT_PIN == 0){
MRF24J40_IF = 1;
}
#endif
}