void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
uart_init();
led_init();
}
void matrix_init_kb(void) {
LED_ON();
_delay_ms(500);
LED_OFF();
matrix_init_user();
}
void matrix_init_kb(void)
{
matrix_init_user();
// Configure the Layer LED
// Set up 16 bit PWM: Fast PWM, mode 15, inverted
TCCR1A = 0b11111110;
TCCR1B = 0b00011001;
ICR1 = 0xFFFF;
// PWM values - 0xFFFF = off, 0x0000 = max
OCR1C = 0x0000; // B7 - Blue
OCR1B = 0x0000; // B6 - Green
OCR1A = 0x0FFF; // B5 - Red
// Set as output
DDRB |= 0b11100000;
#ifndef AUDIO_ENABLE
// If we're not using the audio pin, drive it low
sbi(DDRC, 6);
cbi(PORTC, 6);
#endif
#ifdef ISSI_ENABLE
issi_init();
#endif
#ifdef WATCHDOG_ENABLE
// This is done after turning the layer LED red, if we're caught in a loop
// we should get a flashing red light
wdt_enable(WDTO_500MS);
#endif
}
void matrix_init_kb(void) {
// Turn status LED on
DDRE |= (1<<6);
PORTE |= (1<<6);
matrix_init_user();
}
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
// JTAG disable for PORT F. write JTD bit twice within four cycles.
MCUCR |= (1<<JTD);
MCUCR |= (1<<JTD);
};
void matrix_init_kb(void) {
#ifdef AUDIO_ENABLE
_delay_ms(20); // gets rid of tick
PLAY_SONG(tone_startup);
#endif
matrix_init_user();
};
void matrix_init_kb(void) {
matrix_init_user();
palSetPadMode(GPIOB, 8, PAL_MODE_OUTPUT_PUSHPULL);
palSetPadMode(GPIOB, 9, PAL_MODE_OUTPUT_PUSHPULL);
palClearPad(GPIOB, 8);
palClearPad(GPIOB, 9);
}
void matrix_init_kb(void) {
#ifdef BACKLIGHT_ENABLE
backlight_init_ports();
#endif
// Turn status LED on
DDRE |= (1<<6);
PORTE |= (1<<6);
matrix_init_user();
};
void matrix_init_kb(void) {
// // green led on
// DDRD |= (1<<5);
// PORTD &= ~(1<<5);
// // orange led on
// DDRB |= (1<<0);
// PORTB &= ~(1<<0);
matrix_init_user();
};
void matrix_init(void)
{
debug_enable = true;
//debug_matrix = true;
//debug_keyboard = true;
//debug_mouse = false;
ps2_host_init();
// initialize matrix state: all keys off
for (uint8_t i=0; i < MATRIX_ROWS; i++) matrix[i] = 0x00;
matrix_init_user();
return;
}
void matrix_init_kb(void)
{
bootmagic_lite();
// If the EEPROM has the magic, the data is good.
// OK to load from EEPROM.
if (eeprom_is_valid())
{
backlight_config_load();
// TODO: do something to "turn on" keymaps in EEPROM?
}
else
{
// If the EEPROM has not been saved before, or is out of date,
// save the default values to the EEPROM. Default values
// come from construction of the zeal_backlight_config instance.
backlight_config_save();
// Clear the LED colors stored in EEPROM
for ( int row=0; row < MATRIX_ROWS; row++ )
{
HSV hsv;
for ( int column=0; column < MATRIX_COLS; column++ )
{
hsv.h = rand() & 0xFF;
hsv.s = rand() & 0x7F;
hsv.v = 255;
backlight_set_key_color( row, column, hsv );
}
}
// This saves "empty" keymaps so it falls back to the keymaps
// in the firmware (aka. progmem/flash)
keymap_default_save();
// Save the magic number last, in case saving was interrupted
eeprom_set_valid(true);
}
// Initialize LED drivers for backlight.
backlight_init_drivers();
backlight_timer_init();
backlight_timer_enable();
matrix_init_user();
}
void matrix_init_kb(void) {
#ifdef AUDIO_ENABLE
_delay_ms(20); // gets rid of tick
PLAY_NOTE_ARRAY(tone_startup, false, 0);
#endif
// // green led on
// DDRD |= (1<<5);
// PORTD &= ~(1<<5);
// // orange led on
// DDRB |= (1<<0);
// PORTB &= ~(1<<0);
matrix_init_user();
};
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
MCUCR |= (1<<JTD);
MCUCR |= (1<<JTD);
#ifdef BACKLIGHT_ENABLE
backlight_init_ports();
#endif
// Turn status LED on
DDRE |= (1<<6);
PORTE |= (1<<6);
matrix_init_user();
}
void matrix_init_kb(void)
{
debug_enable=true;
print("meira matrix_init_kb\n");
#ifdef ISSI_ENABLE
issi_init();
#endif
backlight_set(5);
#ifdef WATCHDOG_ENABLE
// This is done after turning the layer LED red, if we're caught in a loop
// we should get a flashing red light
wdt_enable(WDTO_500MS);
#endif
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
}
void matrix_init_kb(void) {
blink_all_leds();
matrix_init_user();
}
void matrix_init_kb(void) {
matrix_init_user();
}
//_____COMMON__________________________________________________________________
// user-defined overridable functions
__attribute__((weak)) void matrix_init_kb(void) { matrix_init_user(); }
void matrix_init_kb(void) {
// Keyboard start-up code goes here
// Runs once when the firmware starts up
matrix_init_user();
};
void matrix_init_kb(void) {
ergodox_led_init();
ergodox_blink_all_leds();
matrix_init_user();
}
void matrix_init_kb (void) {
matrix_init_user();
led_init_ports();
}
void matrix_init_kb(void) {
i2c_init();
// call user level keymaps, if any
matrix_init_user();
}