void
mixer_handle_text(const void *buffer, size_t length)
{
/* do not allow a mixer change while outputs armed */
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_OUTPUTS_ARMED)) {
return;
}
px4io_mixdata *msg = (px4io_mixdata *)buffer;
isr_debug(2, "mix txt %u", length);
if (length < sizeof(px4io_mixdata))
return;
unsigned text_length = length - sizeof(px4io_mixdata);
switch (msg->action) {
case F2I_MIXER_ACTION_RESET:
isr_debug(2, "reset");
/* FIRST mark the mixer as invalid */
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
/* THEN actually delete it */
mixer_group.reset();
mixer_text_length = 0;
/* FALLTHROUGH */
case F2I_MIXER_ACTION_APPEND:
isr_debug(2, "append %d", length);
/* check for overflow - this would be really fatal */
if ((mixer_text_length + text_length + 1) > sizeof(mixer_text)) {
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
return;
}
/* append mixer text and nul-terminate */
memcpy(&mixer_text[mixer_text_length], msg->text, text_length);
mixer_text_length += text_length;
mixer_text[mixer_text_length] = '\0';
isr_debug(2, "buflen %u", mixer_text_length);
/* process the text buffer, adding new mixers as their descriptions can be parsed */
unsigned resid = mixer_text_length;
mixer_group.load_from_buf(&mixer_text[0], resid);
/* if anything was parsed */
if (resid != mixer_text_length) {
/* only set mixer ok if no residual is left over */
if (resid == 0) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_MIXER_OK;
} else {
/* not yet reached the end of the mixer, set as not ok */
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
}
isr_debug(2, "used %u", mixer_text_length - resid);
/* copy any leftover text to the base of the buffer for re-use */
if (resid > 0)
memcpy(&mixer_text[0], &mixer_text[mixer_text_length - resid], resid);
mixer_text_length = resid;
/* update failsafe values */
mixer_set_failsafe();
}
break;
}
}
static int
registers_set_one(uint8_t page, uint8_t offset, uint16_t value)
{
switch (page) {
case PX4IO_PAGE_STATUS:
switch (offset) {
case PX4IO_P_STATUS_ALARMS:
/* clear bits being written */
r_status_alarms &= ~value;
break;
case PX4IO_P_STATUS_FLAGS:
/*
* Allow FMU override of arming state (to allow in-air restores),
* but only if the arming state is not in sync on the IO side.
*/
if (PX4IO_P_STATUS_FLAGS_MIXER_OK & value) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_MIXER_OK;
} else if (!(r_status_flags & PX4IO_P_STATUS_FLAGS_ARM_SYNC)) {
r_status_flags = value;
}
if (PX4IO_P_STATUS_FLAGS_MIXER_OK & r_status_flags) {
/* update failsafe values, now that the mixer is set to ok */
mixer_set_failsafe();
}
break;
default:
/* just ignore writes to other registers in this page */
break;
}
break;
case PX4IO_PAGE_SETUP:
switch (offset) {
case PX4IO_P_SETUP_FEATURES:
value &= PX4IO_P_SETUP_FEATURES_VALID;
/* some of the options conflict - give S.BUS out precedence, then ADC RSSI, then PWM RSSI */
/* switch S.Bus output pin as needed */
#ifdef ENABLE_SBUS_OUT
ENABLE_SBUS_OUT(value & (PX4IO_P_SETUP_FEATURES_SBUS1_OUT | PX4IO_P_SETUP_FEATURES_SBUS2_OUT));
/* disable the conflicting options with SBUS 1 */
if (value & (PX4IO_P_SETUP_FEATURES_SBUS1_OUT)) {
value &= ~(PX4IO_P_SETUP_FEATURES_PWM_RSSI |
PX4IO_P_SETUP_FEATURES_ADC_RSSI |
PX4IO_P_SETUP_FEATURES_SBUS2_OUT);
}
/* disable the conflicting options with SBUS 2 */
if (value & (PX4IO_P_SETUP_FEATURES_SBUS2_OUT)) {
value &= ~(PX4IO_P_SETUP_FEATURES_PWM_RSSI |
PX4IO_P_SETUP_FEATURES_ADC_RSSI |
PX4IO_P_SETUP_FEATURES_SBUS1_OUT);
}
#endif
/* disable the conflicting options with ADC RSSI */
if (value & (PX4IO_P_SETUP_FEATURES_ADC_RSSI)) {
value &= ~(PX4IO_P_SETUP_FEATURES_PWM_RSSI |
PX4IO_P_SETUP_FEATURES_SBUS1_OUT |
PX4IO_P_SETUP_FEATURES_SBUS2_OUT);
}
/* disable the conflicting options with PWM RSSI (without effect here, but for completeness) */
if (value & (PX4IO_P_SETUP_FEATURES_PWM_RSSI)) {
value &= ~(PX4IO_P_SETUP_FEATURES_ADC_RSSI |
PX4IO_P_SETUP_FEATURES_SBUS1_OUT |
PX4IO_P_SETUP_FEATURES_SBUS2_OUT);
}
/* apply changes */
r_setup_features = value;
break;
case PX4IO_P_SETUP_ARMING:
value &= PX4IO_P_SETUP_ARMING_VALID;
/*
* Update arming state - disarm if no longer OK.
* This builds on the requirement that the FMU driver
* asks about the FMU arming state on initialization,
* so that an in-air reset of FMU can not lead to a
* lockup of the IO arming state.
*/
if (value & PX4IO_P_SETUP_ARMING_RC_HANDLING_DISABLED) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_INIT_OK;
}
/*
* If the failsafe termination flag is set, do not allow the autopilot to unset it
*/
value |= (r_setup_arming & PX4IO_P_SETUP_ARMING_TERMINATION_FAILSAFE);
/*
* If failsafe termination is enabled and force failsafe bit is set, do not allow
* the autopilot to clear it.
*/
if (r_setup_arming & PX4IO_P_SETUP_ARMING_TERMINATION_FAILSAFE) {
value |= (r_setup_arming & PX4IO_P_SETUP_ARMING_FORCE_FAILSAFE);
}
r_setup_arming = value;
break;
case PX4IO_P_SETUP_PWM_RATES:
value &= PX4IO_P_SETUP_RATES_VALID;
pwm_configure_rates(value, r_setup_pwm_defaultrate, r_setup_pwm_altrate);
break;
case PX4IO_P_SETUP_PWM_DEFAULTRATE:
if (value < 25) {
value = 25;
}
if (value > 400) {
value = 400;
}
pwm_configure_rates(r_setup_pwm_rates, value, r_setup_pwm_altrate);
break;
case PX4IO_P_SETUP_PWM_ALTRATE:
if (value < 25) {
value = 25;
}
if (value > 400) {
value = 400;
}
pwm_configure_rates(r_setup_pwm_rates, r_setup_pwm_defaultrate, value);
break;
#ifdef CONFIG_ARCH_BOARD_PX4IO_V1
case PX4IO_P_SETUP_RELAYS:
value &= PX4IO_P_SETUP_RELAYS_VALID;
r_setup_relays = value;
POWER_RELAY1((value & PX4IO_P_SETUP_RELAYS_POWER1) ? 1 : 0);
POWER_RELAY2((value & PX4IO_P_SETUP_RELAYS_POWER2) ? 1 : 0);
POWER_ACC1((value & PX4IO_P_SETUP_RELAYS_ACC1) ? 1 : 0);
POWER_ACC2((value & PX4IO_P_SETUP_RELAYS_ACC2) ? 1 : 0);
break;
#endif
case PX4IO_P_SETUP_VBATT_SCALE:
r_page_setup[PX4IO_P_SETUP_VBATT_SCALE] = value;
break;
case PX4IO_P_SETUP_SET_DEBUG:
r_page_setup[PX4IO_P_SETUP_SET_DEBUG] = value;
isr_debug(0, "set debug %u\n", (unsigned)r_page_setup[PX4IO_P_SETUP_SET_DEBUG]);
break;
case PX4IO_P_SETUP_REBOOT_BL:
if (r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) {
// don't allow reboot while armed
break;
}
// check the magic value
if (value != PX4IO_REBOOT_BL_MAGIC) {
break;
}
// we schedule a reboot rather than rebooting
// immediately to allow the IO board to ACK
// the reboot command
schedule_reboot(100000);
break;
case PX4IO_P_SETUP_DSM:
dsm_bind(value & 0x0f, (value >> 4) & 0xF);
break;
case PX4IO_P_SETUP_FORCE_SAFETY_ON:
if (value == PX4IO_FORCE_SAFETY_MAGIC) {
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_SAFETY_OFF;
} else {
return -1;
}
break;
case PX4IO_P_SETUP_FORCE_SAFETY_OFF:
if (value == PX4IO_FORCE_SAFETY_MAGIC) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_SAFETY_OFF;
} else {
return -1;
}
break;
case PX4IO_P_SETUP_RC_THR_FAILSAFE_US:
if (value > 650 && value < 2350) {
r_page_setup[PX4IO_P_SETUP_RC_THR_FAILSAFE_US] = value;
}
break;
case PX4IO_P_SETUP_PWM_REVERSE:
r_page_setup[PX4IO_P_SETUP_PWM_REVERSE] = value;
break;
case PX4IO_P_SETUP_TRIM_ROLL:
case PX4IO_P_SETUP_TRIM_PITCH:
case PX4IO_P_SETUP_TRIM_YAW:
case PX4IO_P_SETUP_SCALE_ROLL:
case PX4IO_P_SETUP_SCALE_PITCH:
case PX4IO_P_SETUP_SCALE_YAW:
r_page_setup[offset] = value;
break;
case PX4IO_P_SETUP_SBUS_RATE:
r_page_setup[offset] = value;
sbus1_set_output_rate_hz(value);
break;
default:
return -1;
}
break;
case PX4IO_PAGE_RC_CONFIG: {
/**
* do not allow a RC config change while safety is off
*/
if (r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) {
break;
}
unsigned channel = offset / PX4IO_P_RC_CONFIG_STRIDE;
unsigned index = offset - channel * PX4IO_P_RC_CONFIG_STRIDE;
uint16_t *conf = &r_page_rc_input_config[channel * PX4IO_P_RC_CONFIG_STRIDE];
if (channel >= PX4IO_RC_INPUT_CHANNELS) {
return -1;
}
/* disable the channel until we have a chance to sanity-check it */
conf[PX4IO_P_RC_CONFIG_OPTIONS] &= PX4IO_P_RC_CONFIG_OPTIONS_ENABLED;
switch (index) {
case PX4IO_P_RC_CONFIG_MIN:
case PX4IO_P_RC_CONFIG_CENTER:
case PX4IO_P_RC_CONFIG_MAX:
case PX4IO_P_RC_CONFIG_DEADZONE:
case PX4IO_P_RC_CONFIG_ASSIGNMENT:
conf[index] = value;
break;
case PX4IO_P_RC_CONFIG_OPTIONS:
value &= PX4IO_P_RC_CONFIG_OPTIONS_VALID;
r_status_flags |= PX4IO_P_STATUS_FLAGS_INIT_OK;
/* clear any existing RC disabled flag */
r_setup_arming &= ~(PX4IO_P_SETUP_ARMING_RC_HANDLING_DISABLED);
/* set all options except the enabled option */
conf[index] = value & ~PX4IO_P_RC_CONFIG_OPTIONS_ENABLED;
/* should the channel be enabled? */
/* this option is normally set last */
if (value & PX4IO_P_RC_CONFIG_OPTIONS_ENABLED) {
uint8_t count = 0;
bool disabled = false;
/* assert min..center..max ordering */
if (conf[PX4IO_P_RC_CONFIG_MIN] < 500) {
count++;
}
if (conf[PX4IO_P_RC_CONFIG_MAX] > 2500) {
count++;
}
if (conf[PX4IO_P_RC_CONFIG_CENTER] < conf[PX4IO_P_RC_CONFIG_MIN]) {
count++;
}
if (conf[PX4IO_P_RC_CONFIG_CENTER] > conf[PX4IO_P_RC_CONFIG_MAX]) {
count++;
}
/* assert deadzone is sane */
if (conf[PX4IO_P_RC_CONFIG_DEADZONE] > 500) {
count++;
}
if (conf[PX4IO_P_RC_CONFIG_ASSIGNMENT] == UINT8_MAX) {
disabled = true;
} else if ((conf[PX4IO_P_RC_CONFIG_ASSIGNMENT] >= PX4IO_RC_MAPPED_CONTROL_CHANNELS) &&
(conf[PX4IO_P_RC_CONFIG_ASSIGNMENT] != PX4IO_P_RC_CONFIG_ASSIGNMENT_MODESWITCH)) {
count++;
}
/* sanity checks pass, enable channel */
if (count) {
isr_debug(0, "ERROR: %d config error(s) for RC%d.\n", count, (channel + 1));
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_INIT_OK;
} else if (!disabled) {
conf[index] |= PX4IO_P_RC_CONFIG_OPTIONS_ENABLED;
}
}
break;
/* inner switch: case PX4IO_P_RC_CONFIG_OPTIONS */
}
break;
/* case PX4IO_RC_PAGE_CONFIG */
}
case PX4IO_PAGE_TEST:
switch (offset) {
case PX4IO_P_TEST_LED:
LED_AMBER(value & 1);
break;
}
break;
default:
return -1;
}
return 0;
}
int
mixer_handle_text(const void *buffer, size_t length)
{
/* do not allow a mixer change while safety off and FMU armed */
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) &&
(r_setup_arming & PX4IO_P_SETUP_ARMING_FMU_ARMED)) {
return 1;
}
/* disable mixing, will be enabled once load is complete */
r_status_flags &= ~(PX4IO_P_STATUS_FLAGS_MIXER_OK);
/* abort if we're in the mixer - the caller is expected to retry */
if (in_mixer) {
return 1;
}
px4io_mixdata *msg = (px4io_mixdata *)buffer;
isr_debug(2, "mix txt %u", length);
if (length < sizeof(px4io_mixdata)) {
return 0;
}
unsigned text_length = length - sizeof(px4io_mixdata);
switch (msg->action) {
case F2I_MIXER_ACTION_RESET:
isr_debug(2, "reset");
/* THEN actually delete it */
mixer_group.reset();
mixer_text_length = 0;
/* FALLTHROUGH */
case F2I_MIXER_ACTION_APPEND:
isr_debug(2, "append %d", length);
/* check for overflow - this would be really fatal */
if ((mixer_text_length + text_length + 1) > sizeof(mixer_text)) {
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
return 0;
}
/* append mixer text and nul-terminate, guard against overflow */
memcpy(&mixer_text[mixer_text_length], msg->text, text_length);
mixer_text_length += text_length;
mixer_text[mixer_text_length] = '\0';
isr_debug(2, "buflen %u", mixer_text_length);
/* process the text buffer, adding new mixers as their descriptions can be parsed */
unsigned resid = mixer_text_length;
mixer_group.load_from_buf(&mixer_text[0], resid);
/* if anything was parsed */
if (resid != mixer_text_length) {
/* only set mixer ok if no residual is left over */
if (resid == 0) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_MIXER_OK;
} else {
/* not yet reached the end of the mixer, set as not ok */
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
}
isr_debug(2, "used %u", mixer_text_length - resid);
/* copy any leftover text to the base of the buffer for re-use */
if (resid > 0)
memcpy(&mixer_text[0], &mixer_text[mixer_text_length - resid], resid);
mixer_text_length = resid;
/* update failsafe values */
mixer_set_failsafe();
}
break;
}
return 0;
}
